User`s guide
Table Of Contents
- User’s Guide
- 1 Getting Started
- 2 Introduction
- 3 Installation
- 4 Using EasyEXPERT
- 5 Classic Test Definition
- I/V Sweep
- Multi Channel I/V Sweep
- I/V List Sweep
- I/V-t Sampling
- C-V Sweep
- Direct Control
- Function Setup
- Auto Analysis Setup
- Display Setup
- SMU Range Setup Window
- ADC and Integration Time Setup Window
- Advanced Setup Window
- CMU Range Setup Window
- Advanced Setup Window for C-V Sweep
- Switching Matrix Control
- SPGU Control
- SPGU Pulse Setup Window
- Load Z Setup Window
- Pulse Switch Setup Window
- SPGU ALWG Setup Window
- Define ALWG Waveform Window
- 6 Application Test Definition
- 7 Function Details
- I/V Sweep Measurement
- Multi Channel I/V Sweep Measurement
- I/V-t Sampling Measurement
- C-V Sweep Measurement
- SPGU Module
- Sweep Abort Function
- Standby Function
- Bias Hold Function
- Current Offset Cancel
- SMU CMU Unify Unit
- Atto Sense and Switch Unit
- SMU/PG Selector
- SMU Ranging Mode
- SMU Compliance
- SMU Pulse
- SMU Measurement Time
- SMU Filter
- SMU Series Resistor
- Interlock Function
- Auto Power Off Function
- Initial Settings
- 8 Built-in Programming Tool
- 9 If You Have a Problem
- When You Operate B1500A
- When You Perform Measurement
- Measurement Takes More Time than Specified
- Noise Affects the Measured Values
- Voltage Measurement Error is Large
- SMU Oscillates for High-Frequency Device Measurements
- SMU Oscillates for Negative Resistance Measurements
- Large Current Causes High Temperature (Thermal Drift)
- Measurement Damages the Device under Test
- Leaving Connections Damages Devices after Measurement
- Unexpected Sampling Measurement Data is Returned
- MFCMU Causes Unbalance Condition
- Before Shipping to Service Center
- Data Backup and Recovery
- B1500A System Recovery
- Updating EasyEXPERT
- Error Codes
- 10 Application Library and Utilities
9-68 Agilent B1500 User’s Guide, Edition 7
If You Have a Problem
Error Codes
2452 4.5 Vref Internal ADC function test failed.
2453 Power Amp initial test failed.
2454 Filter & Amp test failed.
2455 Internal temperature test failed.
2456 Internal output resistance test failed.
2481 Invalid frame configuration.
2482 Frame has no modules.
2483 PLL not locked in slave module.
2484 Reference line is not connected.
2485 Sync line is not connected.
2486 Interrupt line is not available.
2487 Module service request assertion test failed.
2488 Module service request detection test failed.
2489 Emergency interrupt is not available.
2500 SPGU calibration failed.
2501 Power Amp idling calibration failed.
2502 DAC output level calibration failed.
3002 WGFMU initialization failure.
3003 WGFMU FPGA is not configured.
3004 EEPROM CRC data of system timing data is invalid.
3005 EEPROM CRC data of DAC DCM PS data is invalid.
3006 EEPROM CRC data of ADC DCM PS data is invalid.
3007 EEPROM CRC data of DAC clock edge data is invalid.
3008 EEPROM CRC data of ADC clock edge data is invalid.
3009 EEPROM CRC data of DAC level calibration data is invalid.
3010 EEPROM CRC data of ADC level calibration data is invalid.
3011 EEPROM CRC data of DAC skew calibration data is invalid.
3012 EEPROM CRC data of ADC skew calibration data is invalid.