User`s guide
Table Of Contents
- User’s Guide
- 1 Getting Started
- 2 Introduction
- 3 Installation
- 4 Using EasyEXPERT
- 5 Classic Test Definition
- I/V Sweep
- Multi Channel I/V Sweep
- I/V List Sweep
- I/V-t Sampling
- C-V Sweep
- Direct Control
- Function Setup
- Auto Analysis Setup
- Display Setup
- SMU Range Setup Window
- ADC and Integration Time Setup Window
- Advanced Setup Window
- CMU Range Setup Window
- Advanced Setup Window for C-V Sweep
- Switching Matrix Control
- SPGU Control
- SPGU Pulse Setup Window
- Load Z Setup Window
- Pulse Switch Setup Window
- SPGU ALWG Setup Window
- Define ALWG Waveform Window
- 6 Application Test Definition
- 7 Function Details
- I/V Sweep Measurement
- Multi Channel I/V Sweep Measurement
- I/V-t Sampling Measurement
- C-V Sweep Measurement
- SPGU Module
- Sweep Abort Function
- Standby Function
- Bias Hold Function
- Current Offset Cancel
- SMU CMU Unify Unit
- Atto Sense and Switch Unit
- SMU/PG Selector
- SMU Ranging Mode
- SMU Compliance
- SMU Pulse
- SMU Measurement Time
- SMU Filter
- SMU Series Resistor
- Interlock Function
- Auto Power Off Function
- Initial Settings
- 8 Built-in Programming Tool
- 9 If You Have a Problem
- When You Operate B1500A
- When You Perform Measurement
- Measurement Takes More Time than Specified
- Noise Affects the Measured Values
- Voltage Measurement Error is Large
- SMU Oscillates for High-Frequency Device Measurements
- SMU Oscillates for Negative Resistance Measurements
- Large Current Causes High Temperature (Thermal Drift)
- Measurement Damages the Device under Test
- Leaving Connections Damages Devices after Measurement
- Unexpected Sampling Measurement Data is Returned
- MFCMU Causes Unbalance Condition
- Before Shipping to Service Center
- Data Backup and Recovery
- B1500A System Recovery
- Updating EasyEXPERT
- Error Codes
- 10 Application Library and Utilities
9-56 Agilent B1500 User’s Guide, Edition 7
If You Have a Problem
Error Codes
312 SCUU control cable was connected/disconnected.
The B1500 must be turned off when the SMU CMU Unify Unit
(SCUU) is connected
/disconnected.
320 Excess current in CMU.
Current that exceeds maximum current at the present voltage range was
detected by
the CMU. The output switch was set to OFF.
321 This command is not available for CMU.
CMU was specified for the SMU dedicated command. Specify SMU.
322 This command is not available for SMU.
SMU was specified for the CMU dedicated command. Specify CMU.
323 Use SSP instead of CN for SCUU modules.
It is not necessary to specify the
modules conn
ected to the SMU CMU
Unify Unit (SCUU) in the CN command. The output switches will be
controlled by the SSP command.
330 Turn on again to detect source channel.
SCUU might be disconnected/connected on the power on condition.
Restart the B
1500 to detect and enable the channel.
331 Turn on again to detect synchronous channel.
SCUU might be disconnected/connected on the power on condition.
Restart the B
1500 to detect and enable the channel.
332 Turn on again to detect measurement channe
l.
SCUU might be disconnected/connected on the power on condition.
Restart the B
1500 to detect and enable the channel.
333 Turn on again to detect search source.
SCUU might be disconnected/connected on the power on condition.
Restart the B
1500 to detect and enable the channel.
334 Turn on again to detect search sync source.
SCUU might be disconnected/connected on the power on condition.
Restart the B
1500 to detect and enable the channel.
335 Turn on again to detect search monitor channe
l.
SCUU might be disconnected/connected on the power on condition.
Restart the B
1500 to detect and enable the channel.