User`s guide
Table Of Contents
- User’s Guide
- 1 Getting Started
- 2 Introduction
- 3 Installation
- 4 Using EasyEXPERT
- 5 Classic Test Definition
- I/V Sweep
- Multi Channel I/V Sweep
- I/V List Sweep
- I/V-t Sampling
- C-V Sweep
- Direct Control
- Function Setup
- Auto Analysis Setup
- Display Setup
- SMU Range Setup Window
- ADC and Integration Time Setup Window
- Advanced Setup Window
- CMU Range Setup Window
- Advanced Setup Window for C-V Sweep
- Switching Matrix Control
- SPGU Control
- SPGU Pulse Setup Window
- Load Z Setup Window
- Pulse Switch Setup Window
- SPGU ALWG Setup Window
- Define ALWG Waveform Window
- 6 Application Test Definition
- 7 Function Details
- I/V Sweep Measurement
- Multi Channel I/V Sweep Measurement
- I/V-t Sampling Measurement
- C-V Sweep Measurement
- SPGU Module
- Sweep Abort Function
- Standby Function
- Bias Hold Function
- Current Offset Cancel
- SMU CMU Unify Unit
- Atto Sense and Switch Unit
- SMU/PG Selector
- SMU Ranging Mode
- SMU Compliance
- SMU Pulse
- SMU Measurement Time
- SMU Filter
- SMU Series Resistor
- Interlock Function
- Auto Power Off Function
- Initial Settings
- 8 Built-in Programming Tool
- 9 If You Have a Problem
- When You Operate B1500A
- When You Perform Measurement
- Measurement Takes More Time than Specified
- Noise Affects the Measured Values
- Voltage Measurement Error is Large
- SMU Oscillates for High-Frequency Device Measurements
- SMU Oscillates for Negative Resistance Measurements
- Large Current Causes High Temperature (Thermal Drift)
- Measurement Damages the Device under Test
- Leaving Connections Damages Devices after Measurement
- Unexpected Sampling Measurement Data is Returned
- MFCMU Causes Unbalance Condition
- Before Shipping to Service Center
- Data Backup and Recovery
- B1500A System Recovery
- Updating EasyEXPERT
- Error Codes
- 10 Application Library and Utilities
9-36 Agilent B1500 User’s Guide, Edition 7
If You Have a Problem
Error Codes
113023 Value for string parameter is not contained in the enumeration. Value
must be a member of the enumeration. Parameter name: A, Parameter
value: B, En
umeration: C
113024 Value for module parameter is invalid or is not compliant to the
resource type
of the parameter. Parameter name: A, Parameter value: B
113025 Improper value specified for the vector parameter. The value must be
within the follow
ing range.
Restriction: A, Specified value: B, Effective range: C to
D
113031 Test setup A depends on
an undefined application test B. Please import
the application test B in advance.
114001 A preset group named A already exists. The p
reset group name must be
unique.
114002 Unnamed preset group cannot be exported. Please name the preset
group in ad
vance.
114011 A test setup named A is already in the pr
eset group B. The test setup
name must be unique in a preset group.
114012 A test setup named A cannot be retr
ieved in the preset group B.
Probably it had already been modified or deleted.
114021 Following test result record cannot be retrieved. Pro
bably it had already
been deleted. Test result record: A
114031 Change the file name in the File Name Format dialog box. Following
elements can be us
ed in the file name.
A Setup Name
B Date (Time stamp)
C Count
D Device ID
1
1
40
32
Ch
ange the file name in the File Name Format di
alog box. Specified
value contains an invalid character. Specified file name: A,
Invalid character: B
11
4101 File I/O error occurred during automatic data export. Refer to the detail
message,
and retry after taking necessary measures.
114102 Specify the folder path in the Test Results Data Auto Export dialog box.
114103 Change the folder path in the Test Results Data Auto Export dialog box.
Specified value contains an invalid character
. Specified folder path: A