User`s guide
Table Of Contents
- User’s Guide
- 1 Getting Started
- 2 Introduction
- 3 Installation
- 4 Using EasyEXPERT
- 5 Classic Test Definition
- I/V Sweep
- Multi Channel I/V Sweep
- I/V List Sweep
- I/V-t Sampling
- C-V Sweep
- Direct Control
- Function Setup
- Auto Analysis Setup
- Display Setup
- SMU Range Setup Window
- ADC and Integration Time Setup Window
- Advanced Setup Window
- CMU Range Setup Window
- Advanced Setup Window for C-V Sweep
- Switching Matrix Control
- SPGU Control
- SPGU Pulse Setup Window
- Load Z Setup Window
- Pulse Switch Setup Window
- SPGU ALWG Setup Window
- Define ALWG Waveform Window
- 6 Application Test Definition
- 7 Function Details
- I/V Sweep Measurement
- Multi Channel I/V Sweep Measurement
- I/V-t Sampling Measurement
- C-V Sweep Measurement
- SPGU Module
- Sweep Abort Function
- Standby Function
- Bias Hold Function
- Current Offset Cancel
- SMU CMU Unify Unit
- Atto Sense and Switch Unit
- SMU/PG Selector
- SMU Ranging Mode
- SMU Compliance
- SMU Pulse
- SMU Measurement Time
- SMU Filter
- SMU Series Resistor
- Interlock Function
- Auto Power Off Function
- Initial Settings
- 8 Built-in Programming Tool
- 9 If You Have a Problem
- When You Operate B1500A
- When You Perform Measurement
- Measurement Takes More Time than Specified
- Noise Affects the Measured Values
- Voltage Measurement Error is Large
- SMU Oscillates for High-Frequency Device Measurements
- SMU Oscillates for Negative Resistance Measurements
- Large Current Causes High Temperature (Thermal Drift)
- Measurement Damages the Device under Test
- Leaving Connections Damages Devices after Measurement
- Unexpected Sampling Measurement Data is Returned
- MFCMU Causes Unbalance Condition
- Before Shipping to Service Center
- Data Backup and Recovery
- B1500A System Recovery
- Updating EasyEXPERT
- Error Codes
- 10 Application Library and Utilities
9-32 Agilent B1500 User’s Guide, Edition 7
If You Have a Problem
Error Codes
109022 The value of standard for CMU short correction must be finite as
impedance.
109031 CMU load correction failed.
109032 The value of standard for CMU load correction
must be finite in
impedance (non-zero as admittance).
109041 Cannot define multiple standby settings for a SMU. Channel: A
109051 Direct Control execution status. Sweep measurement was aborted by
the automa
tic abort function or the power compliance. Test setup: A
109052 Direct Control execution status. Quasi-static CV measurement was
aborted by th
e automatic abort function. Test setup: A
109053 Direct Control execution status. Search measurement was abo
rted by
the automatic abort function. Test setup: A
109054 Direct Control execution status. Sampling measu
rement was aborted by
the automatic abort function. Test setup: A
109061 Duplicate SMU assignment was found. SMU assignment must be
unique. SM
U: A
110001 Configuration query completed.
111001 Data name (A) is invalid
.
111002 Function name (A) is invalid
.
111003 Function name (A) duplica
tes other data/function name.
111004 Definition expression of function (A) is invalid
. expression: B
111005 The data (A) assigned with
the data (B) is not defined.
111006 The data (A) assigned to the d
ata (B) is not defined.
111007 The data (A) cannot be ass
igned to the data (B) for the mismatch of
their types.
111008 Recursive definition is not allowed for function (A). Expres
sion: B
111011 Vector data expression is expected. Expression: A
111012 Numeric expression is expected. Expression: A
111013 String expression is expected. Expression: A
111014 Descriptor expression is expected. Expression: A
111015 Module descriptor expression is expected. Expression: A