User`s guide
Table Of Contents
- User’s Guide
- 1 Getting Started
- 2 Introduction
- 3 Installation
- 4 Using EasyEXPERT
- 5 Classic Test Definition
- I/V Sweep
- Multi Channel I/V Sweep
- I/V List Sweep
- I/V-t Sampling
- C-V Sweep
- Direct Control
- Function Setup
- Auto Analysis Setup
- Display Setup
- SMU Range Setup Window
- ADC and Integration Time Setup Window
- Advanced Setup Window
- CMU Range Setup Window
- Advanced Setup Window for C-V Sweep
- Switching Matrix Control
- SPGU Control
- SPGU Pulse Setup Window
- Load Z Setup Window
- Pulse Switch Setup Window
- SPGU ALWG Setup Window
- Define ALWG Waveform Window
- 6 Application Test Definition
- 7 Function Details
- I/V Sweep Measurement
- Multi Channel I/V Sweep Measurement
- I/V-t Sampling Measurement
- C-V Sweep Measurement
- SPGU Module
- Sweep Abort Function
- Standby Function
- Bias Hold Function
- Current Offset Cancel
- SMU CMU Unify Unit
- Atto Sense and Switch Unit
- SMU/PG Selector
- SMU Ranging Mode
- SMU Compliance
- SMU Pulse
- SMU Measurement Time
- SMU Filter
- SMU Series Resistor
- Interlock Function
- Auto Power Off Function
- Initial Settings
- 8 Built-in Programming Tool
- 9 If You Have a Problem
- When You Operate B1500A
- When You Perform Measurement
- Measurement Takes More Time than Specified
- Noise Affects the Measured Values
- Voltage Measurement Error is Large
- SMU Oscillates for High-Frequency Device Measurements
- SMU Oscillates for Negative Resistance Measurements
- Large Current Causes High Temperature (Thermal Drift)
- Measurement Damages the Device under Test
- Leaving Connections Damages Devices after Measurement
- Unexpected Sampling Measurement Data is Returned
- MFCMU Causes Unbalance Condition
- Before Shipping to Service Center
- Data Backup and Recovery
- B1500A System Recovery
- Updating EasyEXPERT
- Error Codes
- 10 Application Library and Utilities
9-30 Agilent B1500 User’s Guide, Edition 7
If You Have a Problem
Error Codes
105912 Test execution error was detected. Check the parameter values of the
command, and set the Arguments field again. Setup Name=A, Line
Number=B, Command=C
1
05913 Incorrect usage of ST and END commands. Use them as
a pair to store
a command group into the program memory.
105914 Improper number of Arguments for the A command. Enter
the
Arguments correctly.
106001 Logon request was rejected. The number of Logons already reaches the
limit of the software
regulation. Restart EasyEXPERT. If this does not
solve the problem, restart the B1500.
107001 Workspace management error was occurred.
107002 Workspace was not found. Restart Agilent B1500A. If the problem still
occurs, contact your neares
t Agilent Technologies Service Center.
107003 Workspace could not be loaded. Restart Agilent B1500A. If the
proble
m still occurs, contact your nearest Agilent Technologies Service
Center.
107004 The request to load or create Workspace was rejected. Workspace is
already active. Close the
present Workspace and open the Workspace
again.
107005 The operation cannot be executed because Workspace is in use now.
Close t
he present Workspace and open the Workspace again.
107006 The workspace name is conflicting. It must be unique in system.
Specify the correct Worksp
ace name.
108001 Function Library management error occurred.
108002 Function Library function has not been configured correctly or is not
running
. Restart Agilent B1500A. If the problem still occurs, contact
your nearest Agilent Technologies Service Center.
108003 Invalid Function Module assembly file. Restart Agilent B1500A. If the
proble
m still occurs, contact your nearest Agilent Technologies Service
Center.
108004 Invalid Function Module. Restart Agilent B1500A. If the problem still
occurs, contact your neares
t Agilent Technologies Service Center.
108005 Function Module was not found. Restart Agilent B1500A. If the
proble
m still occurs, contact your nearest Agilent Technologies Service
Center.