User`s guide
Table Of Contents
- User’s Guide
- 1 Getting Started
- 2 Introduction
- 3 Installation
- 4 Using EasyEXPERT
- 5 Classic Test Definition
- I/V Sweep
- Multi Channel I/V Sweep
- I/V List Sweep
- I/V-t Sampling
- C-V Sweep
- Direct Control
- Function Setup
- Auto Analysis Setup
- Display Setup
- SMU Range Setup Window
- ADC and Integration Time Setup Window
- Advanced Setup Window
- CMU Range Setup Window
- Advanced Setup Window for C-V Sweep
- Switching Matrix Control
- SPGU Control
- SPGU Pulse Setup Window
- Load Z Setup Window
- Pulse Switch Setup Window
- SPGU ALWG Setup Window
- Define ALWG Waveform Window
- 6 Application Test Definition
- 7 Function Details
- I/V Sweep Measurement
- Multi Channel I/V Sweep Measurement
- I/V-t Sampling Measurement
- C-V Sweep Measurement
- SPGU Module
- Sweep Abort Function
- Standby Function
- Bias Hold Function
- Current Offset Cancel
- SMU CMU Unify Unit
- Atto Sense and Switch Unit
- SMU/PG Selector
- SMU Ranging Mode
- SMU Compliance
- SMU Pulse
- SMU Measurement Time
- SMU Filter
- SMU Series Resistor
- Interlock Function
- Auto Power Off Function
- Initial Settings
- 8 Built-in Programming Tool
- 9 If You Have a Problem
- When You Operate B1500A
- When You Perform Measurement
- Measurement Takes More Time than Specified
- Noise Affects the Measured Values
- Voltage Measurement Error is Large
- SMU Oscillates for High-Frequency Device Measurements
- SMU Oscillates for Negative Resistance Measurements
- Large Current Causes High Temperature (Thermal Drift)
- Measurement Damages the Device under Test
- Leaving Connections Damages Devices after Measurement
- Unexpected Sampling Measurement Data is Returned
- MFCMU Causes Unbalance Condition
- Before Shipping to Service Center
- Data Backup and Recovery
- B1500A System Recovery
- Updating EasyEXPERT
- Error Codes
- 10 Application Library and Utilities
Agilent B1500 User’s Guide, Edition 7 4- 53
Using EasyEXPERT
Data Display
Data Display GUI
Setup Name This field just displays the name of the test setup used to get this test record.
X-Y Graph Plot This area displays the measurement result graph, traces, ma
rker, cursor, and lines.
The Properties button opens “Graph Properties (page 4-63)”.
Parameters This area lists the user-defined output param
eters if the outp
ut parameters are set.
List Display This area displays the measurement result data list. The Properties button opens
“List Display Properties (page 4-64)”.
pin The Data Display window can keep up to 10 display layers. And the earliest layer
o
ver 10 will be
automatically deleted. This button is available when the window
keeps at least two layers. If this button shows the standing pin, the layer will be kept.
If this button shows the laid pin, the layer can be deleted.
Double clicking the tab gives the same result as this button.
X This button closes the selected display layer.
File menu Provides the following functions.
Switch to Append Mode /
Switch to
Overwrite Mode Used to
switch the display mode.
Update Test Result Stores the information of the scale and the analysis
tools.
Delete Tes
t Result Deletes the present display data or the selected
display la
yer.
Close This Display Closes the selected display layer.
Close All Displays Closes all display layers.
Save Image As... Opens the Save Image As... dialog box used to
s
p
ecify
the file n
a
me of
the graph image to save.
See Figure 4-3. Available data formats are the
BMP, EMF, GIF, and PNG.
Page Setup... Opens the Page Setup dialog box used to set the
print pag
e.