User`s guide

2-41
GPIB Tutorial and Examples
Program 3
470 !GENERAL MEASUREMENT SET UP SPECIFIED
480 !
490 Uut=714 !GPIB address of Agilent 8922M/S
500 Extloss=-.5 !Loss of cable linking 8922 to mobile (loss=-xdB)
510 Bchpwr=-80 !BCCH power level in dBm
520 Timeouttime=20 !The GPIB timeout in seconds
530 Leveltol=1 !Power tolerence to indicate TX Level has settled
after change (dB)
540 Fpthreshold=.3 !Power tolerence for fast power measurement after ana-
lyzer channel change (dB)
550 !
560 !======================================================================
570 !
580 !MEASUREMENT POINTS ARE DEFINED IN THIS SECTION
590 !
600 !Bit error ratio test
610 !
620 Numberpwr=1 !The number of downlink power levels for bit error
test
630 Berpwr(1)=-102 !The power level in dBm of the first downlink power.
Etc....
640 Bits1=10000 !The number of bits to test at each ARFCN/Power com-
bination
650 Numberarfcn=3 !The number of ARFCN for bit error test
660 Berarfcn(1)=1 !The value of the first ARFCN. Etc....
670 Berarfcn(2)=65
680 Berarfcn(3)=124
690 !
700 !
710 !DSP measurememnts
720 !
730 Numdsppwr=3 !The number of mobile TX Levels for DSP test
740 Dsppwr(1)=5 !The value of the first TX Level. Etc...
750 Dsppwr(2)=10
760 Dsppwr(3)=15
770 Numdsparfcn=3 !The number of ARFCN for DSP test
780 Dsparfcn(1)=1 !The value of the first ARFCN. Etc....
790 Dsparfcn(2)=65
800 Dsparfcn(3)=124
810 !
820 !Fast Power measurements
830 !
840 Numfppwr=8 !The number of mobile TX Levels for fast power test
850 Fppwr(1)=6 !The value of the first TX Level. Etc....
860 Fppwr(2)=7
870 Fppwr(3)=8
880 Fppwr(4)=9
890 Fppwr(5)=11
900 Fppwr(6)=12
910 Fppwr(7)=13
920 Fppwr(8)=14
930 Numfparfcn=3 !The number of ARFCN for fast power test
940 Fparfcn(1)=1 !The value of the first ARFCN. Etc...
950 Fparfcn(2)=65
960 Fparfcn(3)=124
970 !
980 !=========================================================================
990 !
1000 !PRINT MESSAGES ARE DEFINED BELOW
1010 !
1020 Message$(1)=”Answer call when mobile rings”
1030 Message$(2)=”Would you like to test again? (y or n)”
1040 Message$(3)=”Results from Fast Power Measurement”
1050 Message$(4)=”ARFCN TXLEV POWER dBm”
1060 Message$(5)=”Results from Power, Power vs Time & Modulation Measurements”
1070 Message$(6)=”ARFCN TXLEV POWER dBm Pk & RMS PHASE FREQ ERROR MASK”
1080 Message$(7)=”Results from BER Test”
1090 Message$(8)=”ARFCN Downlink dBm BER1% RxQual RxLev TIMERR”