Technical data
ii
© Copyright 2000-2002
Agilent Technologies
All Rights Reserved. Reproduc-
tion, adaptation, or translation
without prior written permission
is prohibited, except as allowed
under copyright laws.
Agilent Part No. 86100-90047
Printed in USA
February 2002
Agilent Technologies
Lightwave Division
3910 Brickway Boulevard
Santa Rosa, CA 95403, USA
Notice.
The information contained in
this document is subject to
change without notice. Compa-
nies, names, and data used in
examples herein are fictitious
unless otherwise noted. Agilent
Technologies makes no warranty
of any kind with regard to this
material, including but not lim-
ited to, the implied warranties of
merchantability and fitness for a
particular purpose. Agilent
Technologies shall not be liable
for errors contained herein or for
incidental or consequential dam-
ages in connection with the fur-
nishing, performance, or use of
this material.
Restricted Rights Legend.
Use, duplication, or disclosure
by the U.S. Government is sub-
ject to restrictions as set forth in
subparagraph (c) (1) (ii) of the
Rights in Technical Data and
Computer Software clause at
DFARS 252.227-7013 for DOD
agencies, and subparagraphs (c)
(1) and (c) (2) of the Commer-
cial Computer Software
Restricted Rights clause at FAR
52.227-19 for other agencies.
Warranty.
This Agilent Technologies
instrument product is warranted
against defects in material and
workmanship for a period of one
year from date of shipment. Dur-
ing the warranty period, Agilent
Technologies will, at its option,
either repair or replace products
which prove to be defective. For
warranty service or repair, this
product must be returned to a
service facility designated by
Agilent Technologies. Buyer
shall prepay shipping charges to
Agilent Technologies and Agi-
lent Technologies shall pay ship-
ping charges to return the
product to Buyer. However,
Buyer shall pay all shipping
charges, duties, and taxes for
products returned to Agilent
Technologies from another
country.
Agilent Technologies warrants
that its software and firmware
designated by Agilent Technolo-
gies for use with an instrument
will execute its programming
instructions when properly
installed on that instrument.
Agilent Technologies does not
warrant that the operation of the
instrument, or software, or firm-
ware will be uninterrupted or
error-free.
Limitation of Warranty.
The foregoing warranty shall not
apply to defects resulting from
improper or inadequate mainte-
nance by Buyer, Buyer-supplied
software or interfacing, unautho-
rized modification or misuse,
operation outside of the environ-
mental specifications for the
product, or improper site prepa-
ration or maintenance.
No other warranty is expressed
or implied. Agilent Technologies
specifically disclaims the
implied warranties of merchant-
ability and fitness for a particu-
lar purpose.
Exclusive Remedies.
The remedies provided herein
are buyer's sole and exclusive
remedies. Agilent Technologies
shall not be liable for any direct,
indirect, special, incidental, or
consequential damages, whether
based on contract, tort, or any
other legal theory.
Safety Symbols.
CAUTION
Caution denotes a hazard. It
calls attention to a procedure
that, if not correctly performed
or adhered to, could result in
damage to or destruction of the
product. Do not proceed beyond
a caution note until the indicated
conditions are fully understood
and met.
WARNING
Warning denotes a hazard. It
calls attention to a procedure
which, if not correctly per-
formed or adhered to, could
result in injury or loss of life. Do
not proceed beyond a warning
sign until the indicated condi-
tions are fully understood and
met.
The instruction docu-
mentation symbol. The
product is marked with
this warning symbol
when it is necessary for
the user to refer to the
instruction in the docu-
mentation.
The AC symbol is used
to indicate the required
nature of the line mod-
ule input power.
| The ON symbols are
used to mark the posi-
tions of the instrument
power line switch.
The Standby symbol is
used to mark the posi-
tion of the instrument
power line switch.
The OFF symbols
are used to mark the
positions of the instru-
ment power line switch.
The CE mark is a regis-
tered trademark of the
European Community.
The CSA mark is a reg-
istered trademark of the
Canadian Standards
Association.
ISM1-A This is a symbol of an
Industrial Scientific and Medical
Group 1 Class A product..
Typographical Conventions.
The following conventions are
used in this book:
key type for keys or text located
on the keyboard or instrument.
softkey type for key names that
are displayed on the instrument’s
screen.
display type for words or
characters displayed on the com-
puter’s screen or instrument’s
display.
user type for words or characters
that you type or enter.
emphasis type for words or char-
acters that emphasize some point
or that are used as place holders
for text that you type.