Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment • FAST SHIPPING AND DELIVERY • TENS OF THOUSANDS OF IN-STOCK ITEMS • EQUIPMENT DEMOS • HUNDREDS OF MANUFACTURERS SUPPORTED • LEASING/MONTHLY RENTALS • ITAR CERTIFIED SECURE ASSET SOLUTIONS SERVICE CENTER REPAIRS Experienced engineers and technicians on staff at our full-service, in-house repair center WE BUY USED EQUIPMENT Sell your excess, underutilized, and idle used equipment We also offer credit for buy-back
Agilent TS-5400 Functional Test System Series IIB System Integrator’s Manual *E8770-90030* Manual Part Number E8770-90030 Agilent Technologies Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
Notices © Agilent Technologies, Inc. 1999 - 2003 Manual Part Number No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Agilent Technologies, Inc. as governed by United States and international copyright laws.
Safety Summary The following general safety precautions must be observed during all phases of operation of this system. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design, manufacture, and intended use of the system. Agilent Technologies, Inc. assumes no liability for the customer's failure to comply with these requirements. WARNING: DO NOT REMOVE ANY SYSTEM COVER Operating personnel must not remove system covers.
Ground the System To minimize shock hazard, the system chassis must have a hard-wired connection to an electrical protective earth ground. The system must also be connected to the ac power mains through a power cable that includes a protective earth conductor. The power cable ground wire must be connected to an electrical ground (safety ground) at the power outlet. Any interruption of the protective grounding will cause a potential shock hazard that could result in personal injury.
Table 1 Safety Symbols and Markings Safety symbols Warning: risk of electric shock. Caution: refer to accompanying documents. Alternating current. Both direct and alternating current. Earth (ground) terminal Protective earth (ground) terminal Frame or chassis terminal Terminal is at earth potential. Used for measurement and control circuits designed to be operated with one terminal at earth potential. Switch setting indicator. O = Off, | = On.
Service and Support Any adjustment, maintenance, or repair of this product must be performed by qualified personnel. Contact your customer engineer through your local Agilent Technologies Service Center. http://www.agilent.com Click the link to Test & Measurement. Select your country from the drop-down menus. The Web page that appears next has contact information specific for your country.
Contents Chapter 1 System Introduction .................................................................................................... 11 Chapter Contents......................................................................................................... 11 Typical System ........................................................................................................... 11 System Software .....................................................................................................
Agilent 6673A DC Power Supply ....................................................................... 49 Chapter 3 Customizing the System .............................................................................................. 51 Chapter Contents......................................................................................................... 51 Customizing the System .............................................................................................
E6170-61613 DAC to Pin Card Aux. Cable............................................................... 85 E6170-61615 DAC to Custom Card Cable................................................................. 86 E6189-61600 Power Supply Power Cable.................................................................. 87 E6230-61603 Heavy-Duty Load Card Cable.............................................................. 88 E6247-61601 Cable-Digitizer (E1563A)........................................................
Glossary ......................................................................................................................... 125 Index .............................................................................................................................. 143 10 Contents Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
Chapter 1 System Introduction Chapter Contents This chapter gives an introduction to the Agilent TS-5400 Functional Test System. Chapter contents are: • Typical System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • System Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • Conceptual Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . • System Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TS-5400 Series II Computer Multicom III/s (computer shelf) Agilent 40101A Agilent 33120 Arb Agilent 34401 Dmm Agilent 1135C PDU Flat Panel Display Keyboard Tray HP1 HP3 HP5 HP7 HP2 HP4 HP6 HP8 TC1 TC2 TC3 TC4 TC5 TC6 Agilent 40107A TC7 E6198A EFT Switch Unit Agilent E6198A Switch/Load Unit TC8 E8401A VXI mainframe Agilent E8401 VXI mainframe Power Supply Power Supply Power Supply Front view Rear View Figure 1-1.
TS-5400 Series I I Hewlett Packard VEi7 Multicom III/s (computer shelf) HP 40101A HEWLETT PACKARD HEWLETT PACKARD HP 34401 Dmm HP 33120 Arb HP 1135C PDU E6198A EFT Switch Unit 15" Flat Panel Display HP E6198 Switch/Load Unit #2 Keyboard Tray HP1 HP3 HP5 HP7 HP2 HP4 HP6 HP8 E6198A EFT Switch Unit HP E6198 Switch/Load Unit #1 TC1 TC2 TC3 TC4 TC5 TC6 TC7 TC8 Express Connect HP E8401 VXI Mainframe HP 40107A HP E8401A VXI mainframe Power Supply Power Supply Power Supply Front vie
System Software The Agilent TS-5400 Series IIB system controller uses the Microsoft Windows XP® operating system, and Agilent TestExec SL software which is pre-installed on your system controller. Refer to the Agilent TS-5400 Online Help and the TestExec SL Online Help (both available from the TestExec SL help menu) for software information. 14 System Introduction Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
Conceptual Block Diagram Figure 1-3 shows is a simplified TS-5400 system block diagram showing the key system hardware components. The system hardware components are described in detail following the figure. Chapter 1 System Introduction Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
Figure 1-3. Agilent TS-5400 System Simplified Block Diagram Optional 53131 Counter Optional 33120 Function Gen.
System Hardware The Agilent TS-5400 systems contain all of the GPIB and/or VXI instrumentation needed to test most electronics modules. You may add additional GPIB instruments and/or VXI modules and cabling to increase the test capabilities of the system. If adding VXI modules when currently no VXI modules are present, requires a VXI Mainframe.
to generate interrupts, trigger delays, and pacing. Agilent E6198A Switch/Load Unit The 21-slot Switch/Load Unit (SLU) holds the pin matrix cards and the load cards. Test system instrumentation, loads and power supplies are routed to the UUT through the pin matrix cards and load cards that plug into the Switch/Load Unit. There are two types of pin matrix cards and four types of load cards (described below).
16 x 5 Instrument Matrix 96-Pin DIN C To Instruments J1 Inst1 Inst2 Inst3 Inst4 Inst5 Inst6 Inst7 Inst8 Inst9 Inst10 Inst11 Inst12 Inst13 Inst14 Inst15 Inst16 DAC1 DAC2 DACCOM P1 Decoding and Driver Circuits 96-Pin DIN C Backplane Access To Switch/Load Unit Abus Access #1 Abus Access #2 Abus Connector J3 Abus2 Abus4 Abus1 Abus3 Disconnect Relays Bypass Relays Aux1 Row1 Aux2 Row2 Aux1 Aux2 Aux3 Aux3 Row3 Aux4 Row4 Aux4 96-Pin DIN C Rear Aux Access P2 J2 96-Pin DIN C Row, Aux & UUT Common To
Agilent E8793A 32-Pin Matrix Module For applications requiring more than 32 channels, the E8793A Pin Matrix card contains a 4x32 switching matrix (no instrument matrix) and may be used for increasing channels in increments of 32. The Analog Bus is daisy-chained from card to card to route the measuring and source instruments to N*32 channels, where N represents the number of Pin Matrix cards including the E8792A.
P1 Decoding and Driver Circuits Abus Connector J3 96-Pin DIN C Backplane Access To Switch/Load Unit Abus2 Abus4 Abus1 Abus3 Disconnect Relays Bypass Relays Aux1 Row1 Aux2 Row2 Aux1 Aux2 Aux3 Aux3 Row3 Aux4 Row4 Aux4 96-Pin DIN C Rear Aux Access P2 J2 96-Pin DIN C Row, Aux & UUT Common To UUT Aux30 Row30 Aux31 Row31 Aux32 Row32 UUT Common Aux30 Aux31 Aux32 32 x 4 Measurement Matrix Matrix Relay Detail: Column Row Figure 1-6.
Load Cards The Agilent TS-5400 Series test systems provide modular design and flexible load switching capabilities.
Test System Interface or Mass Interconnect The Test System Interface or Mass Interconnect connects the test system to your test fixture. The test fixture then connects to the Unit Under Test (UUT). Standard connector blocks allow you to use general purpose connectors designed for low-power and high-power connections as needed.
Figure 1-7. Express Connect Test System Interface 24 System Introduction Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
Mass Interconnect (Mac Panel) The Mac Panel Mass Interconnect uses a high-point count mass interconnect fixture (Agilent E3722A) and interchangeable Interface Test Adapter panels. Figure 1-8 shows the Mac Panel Mass Interconnect features. Refer to the Agilent E6170 Mass Interconnect System User’s Manual supplied with your system for detailed information. Figure 1-8.
rates up to 13 kHz. Measurements for this DMM include Vdc/ac, 2- and 4-wire ohms, offset-compensated ohms, and temperature from thermocouples, thermistors, and RTDs. Agilent 34401 Digital Multimeter Note Agilent 53131 Universal Counter The Agilent 34401 Digital Multimeter (DMM) measures dc voltage, ac-rms voltage, and ohms (including 4-wire ohms). It can also measure temperature by using thermistors. The input to the DMM is balanced and differential.
Agilent 33220 Function/Arbitrary Waveform Generator The Agilent 33220A function / arbitrary waveform generator uses direct digital synthesis (DDS) techniques to create stable, low-distortion output signals. The 33220A provides easy access to standard sine, square, ramp, triangle, and pulse waveforms plus you can create custom waveforms using the 50 MSa/s, 14 bit, 64 K-point arbitrary waveform function.
for Isolated or Non-Isolated channels. Note 28 For additional information, refer to the Agilent E1418A 8/16 Channel D/A Converter Module User’s Manual and SCPI Programming Guide. System Introduction Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
Programmable Power Supplies Table 1-1 lists the Agilent TS-5400 power supply product numbers. Option 014 to any of the product numbers includes cables and rack mount rails (for example, E6187A-014). Each of these GPIB programmable power supplies can operate in either a constant-voltage or constant-current mode over the specified output range. Table 1-1 also lists nominal voltage and current values for each of these power supplies.
30 System Introduction Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
Chapter 2 System Instrument Configuration Chapter Contents This chapter shows how to configure the different VXI and GPIB modules and instruments in the system. Chapter contents are: • VXI Module Locations And Logical Addresses. . . . . . . . . . • Power Supplies Locations and GPIB Addresses. . . . . . . . . . • VXI Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • Programmable Power Supplies . . . . . . . . . . . . . . . . . . . . . . .
VXI Module Locations And Logical Addresses Refer to “VXI Modules” on page 34 for information on how to set the Logical Addresses of the modules. For additional specific information about a particular VXI module, refer to that module’s user manual. For cabling information, refer to Chapter 4, “System Cables and Connectors” on page 63 of this manual.
Table 2-1.
VXI Modules This section describes the individual VXI modules used in an Agilent TS-5400 system, the switch and jumper settings, and cabling to the modules. For additional information on any of these modules, refer to the user’s manual included with each module. Before installing a new or replacement VXI module in a mainframe, verify that its switches or jumpers are set as shown in this section.
Agilent E1333A 3-Channel Universal Counter Module The Agilent E6182A contains an Agilent E1333A B-Size Universal Counter with the Agilent E1403B B-size to C-size Active Adapter Module and cables. The Agilent E1333A Counter performs frequency, time interval, period and totalize measurements. The counter is connected to the UUT through the Agilent E6171 Measurement Control Module. The counter uses only one row on J1, since the counter inputs are referenced to earth ground.
Agilent E1411B Digital Multimeter Module The Agilent E1411B Digital Multimeter (DMM) Module comes standard with the Agilent TS-5400 System. The DMM measures dc voltage, ac-rms voltage, and ohms (including 4-wire ohms). It can also measure temperature by using thermistors. In addition to test measurements, the DMM serves as the system reference and is used to calibrate the V/I functions. The DMM input is balanced and differential.
Agilent E1418A 8/16-Channel Digital/Analog Converter Module The Agilent E1418A is an 8 or 16 channel digital-to-analog converter module. Each channel can be configured for either voltage or current output mode. When configured for voltage output, voltages in the range of -16.0 to +16.0 Volts can be set. When configured for current output, currents in the range of -0.02 to +0.02 Amps can be set.
Cabling Figure 2-4 shows the wiring for the Agilent E1418A DAC Module using the terminal module connector. Two Agilent E3750-61608 cables connect the module to the mass interconnect; the mass interconnect connector has the same pin-out as the module. Refer to Chapter 4 on page 63 for wiring information on the cable. Figure 2-4. Agilent E1418A Terminal Module Connector Pinout 38 System Instrument Configuration Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.
VXI Technology E1563A 2-Channel 800 ka/s Digitizer (ADC) Module The Agilent E6183A contains an VXI Technology E1563A Digitizer and cables. The E1563A Digitizer has two channels that allows simultaneous measurements of two waveforms (for example, the voltage and current waveform of the load signal). In the factory default configuration, Channel 1 provides direct access to the attenuator output.
Agilent E8491B PC Link to VXI Interconnect The E8491B interconnect links the IEEE 1394 bus to the backplane of the VXI mainframe. The E8491B is a C-size device with VXI Resource Manager and Slot 0 capability. There are no configuration switches on the E8491B. The device’s logical address is 0 and it provides the system’s resource manager functionality via software that is part of the Agilent I/O Libraries.
Retaining Screws Seat the module by pushing in the extraction levers Extraction Levers Slide the module into the mainframe until it plugs into the backplane connectors Figure 2-6. Installing the E8491B VXI Interface Card Chapter 2 System Instrument Configuration Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
VXI-MXI-2 Interface Module The VXI-MXI-2 Interface module provides communication between one VXI mainframe and an external controller PC. Refer to Figure 2-7. The VXI-MXI-1 module must be installed in slot 0 of your VXI mainframe. Refer to the Getting Started Guide that came with the module for installation information. Install the PCI-MXI-2 Board into your External PC controller.Refer to the Getting Started Guide that came with the VXI-MXI-2 module for installation information. Figure 2-7.
Agilent E6171B Measurement Control Module The Agilent E6171A/B Measurement Control Module (MCM, also known as the VI card in the Agilent TS-5400 Action documentation) provides four primary functions: 1. It provides a 16x5 matrix used to expand the four columns from the 32-Pin Matrix Module(s) and UUT Common to access up to 16 external instruments. 2.
Isolated V/I Source The V/I programmable current and voltage source are similarly multiplexed to the interconnection column (ABus). The V/I HiV and LoV amplifiers allow the user to source a voltage and measure the current or source a current and measure the voltage. The V/I amplifier is fully isolated. The output is fused, Agilent p/n 2110-0516, at 1 amp. It may be referenced internally to UUT Common through a relay or used differentially.
Switch/Jumper Settings Figure 2-8 shows the Agilent E6171B logical address switch with the switch shown in the factory setting. The logical address for both a one mainframe system and a two mainframe system is the factory default setting of “17”. Refer to “VXI Module Locations And Logical Addresses” on page 32. The Interrupt Priority is always set to 1. Figure 2-8. Agilent E6171B Measurement Control Module Chapter 2 Cabling Figure 2-8 shows the Agilent E6171 Measurement Control module cabling.
Agilent E6173A Arbitrary Waveform Generator (ARB) Module The Agilent E6173A Arbitrary Waveform Generator (formerly the Agilent Z2471A) comes with Agilent E3750-61621 BNC Coax to 3X1 Cables. The Agilent E6173A Arbitrary Waveform Generator is a register based, two-channel isolated (both between channels and from ground) waveform generator. Channel one is connected to the Agilent E6171 Measurement Control Module in the factory default configuration of the Agilent TS-5400 System.
Agilent E6174A 32-Channel Event Detector Module The Agilent E6174A 32-Channel Event Detector (formerly the Agilent Z2902A) comes with cables and an Agilent 91421B ICA connector. The Event Detector provides the capability to analyze 32-channel input event states and timings. The events are stored in memory on the board, then the events can be read back by the controller for event analysis.
Programmable Power Supplies The programmable power supplies, or UUT power supplies, include the Agilent 6642A, 6643A, 6652A, 6653A, 6672A. and 6673A power supplies. These supplies provide power to the unit under test. 48 GPIB Address Selection The first UUT power supply in the system should have a GPIB address number 5. The second power supply should be set to GPIB address 6, and the third power supply to address 7.
Agilent 6673A DC Power Supply The Agilent 6673A DC Power Supply is a 1-output, 0-35 volt, 0-60A GPIB supply. It is not switchable to multiple line voltages. If an Agilent 6673A power option is not specified, then it is set up for 220 - 240 volts and is connected to the Agilent E1135A PDU. Caution The maximum current draw capability of the Agilent 6673A exceeds the breaker size (15A) on the Agilent TS-5400 system and the design specifications of the load cards.
50 System Instrument Configuration Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
Chapter 3 Customizing the System Chapter Contents This chapter discusses steps for installing additional instrumentation and overviews information for common optional products. Additional instrumentation may be incorporated by adding cards to the VXI Mainframe, or adding GPIB controlled external rack-and-stack instruments. Chapter contents are: • Customizing the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 51 • Configuring and Installing Additional VXI Modules . . . . . .
2. Writing and compiling the necessary “instrument handler” or series of “handler action” routines for the instrument and placing them in a DLL. See “Instrument Handlers” on page 59 for more information. 3. Writing a self test for the instrument. Configuring and Installing Additional VXI Modules VXI compatible modules can be installed in the VXI mainframe.
Connecting Instrument Input(s) to the Measurement Control Module Depending on the device, connect the inputs to the UUT either through the Measurement Control Module or directly through the mass interconnect. Table 4-12 lists instrument connector cables to connect the instrumentation inputs to the Agilent E6171 module. For additional information on cables and connectors, refer to Chapter 4 on page 63 Table 3-1. MCM Module Cabling.
Customizing the Agilent TestExec SL Software to Accommodate Additional Instrumentation Each added instrument or altered configuration will require some or all of the following files to be written or modified: 1. A modified ‘SYSTEM.UST’ file. See “Modifying the system.ust File” on page 55 for details. 2. An instrument handler routine. Each instrument type requires a piece of software called an instrument handler be written for it so the instrument can communicate with the Agilent TS-5400 system.
Adding Instruments to the system.ust File The Agilent TS-5400 Test System provides a standard set of pre-installed instruments or modules. These instruments are identified to the test system in the factory-provided ‘system.ust‘ file. This file also lists the aliases and wire nodes used in the system, as shipped from the factory. When instruments are added to the system, you must add them to the system.ust file so that the software can recognize and use the instrument. Modifying the system.
• Some instruments require an Agilent model number in the Name field. For example, the Agilent E6176 is the model number for the 16-Channel High Current Load Card; Agilent 6643A is the model number for the Dual-output GPIB Power Supply (do not use E6187A which is the Agilent TS-5400 Series Product Number for the power supply). • Do not attempt to expand channel nodes (that is, do not double click on individual channel nodes). You cannot change the parameters.
Instrument Reset Management The Agilent TS-5400 system provides an automatic module/instrument reset scheme to help ensure that all modules/instruments are placed into a known safe state before executing a testplan in the event of a problem. The modules/instruments are configured in the system.ust file for the reset operation. Reset Invocation All instrument reset routines are automatically called when: • The system is started.
1. Double-click on the module/instrument name to be edited, or click on the name and then on “Edit” 2. Click on the “InGlobalReset” value and change the value to “1” to enable the reset routine or “0” to disable the routine. 4. Click on “OK” 5. Click on “Save” to save the file or “Save As” to save the file under a different name and/or directory Figure 3-1. Enabling Global Reset Using the System Configuration Editor 58 Customizing the System Artisan Technology Group - Quality Instrumentation ...
Instrument Handlers Instrument Handlers are a layer of software between Agilent TestExec SL and standard instrument drivers (see Figure 3-2). In general, Instrument Handlers are designed to be called from C/C++ code action User Actions Instrument Handler Driver Figure 3-2. Software Layers Instrument handlers contain functions written in C code that are organized by instrument type and function, and require parameters relevant to the function.
Set ‘Set’ prefix is used to set up given configuration to the device. Reset Resets instrument(s) to their power-on state. Clear Clears errors and output buffers. Initiate Puts instrument in ‘wait for trigger’ state. Necessary for external trigger modes requiring continuation of the program after this command is issued to generate the trigger. May also be used to start an immediate reading cycle to be followed by a ‘GetResults’ call. Trigger Generates a software trigger immediately.
Naming Conventions Used in Instrument Handlers Instrument handlers follow these naming conventions: 1. Routine names begin with the lowercase name of the instrument type. Note that this is not a specific device, but a generic one. For example, use ‘dmm’ instead of ‘dmm1411’. This lets handlers be expanded to handle more than one type of similar instrument in the future. 2. There are no underscores separating parts of a function name. Rather, upper and lower cases are used. 3.
62 Customizing the System Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
Chapter 4 System Cables and Connectors Chapter Contents This chapter shows all possible cables used in Agilent E8780 and E8786 Systems. These cables are for all systems--no one system will contain all of these cables. Cables are listed by part number as follows: • E1066-61620, E3750-61603 Twinax 3x1 to Banana . . . . . . page 64 • E1072-61620, E3750-61602 Twinax 3x1 to 3x1 . . . . . . . . . page 64 • E1400-61605 1x6 ABus Ribbon Cable. . . . . . . . . . . . . . . . .
E1066-61620, E3750-61603 Twinax 3x1 to Banana Twinax 3x1 to Banana E1066-61620 (2000mm) E3750-61603 (1200mm) High Low High Drain Low E1072-61620, E3750-61602 Twinax 3x1 to 3x1 Twinax 3x1 to 3x1 E1072-61620 (2000mm) E3750-61602 (1200mm) E1400-61605 1x6 ABus Ribbon Cable E1400-61605 30.7mm 64 System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
E3750-61604, E6170-61614 Male BNC Coax to 3x1 Cable Coax 3x1 to BNC E3750-61604 (1200mm) E6170-61614 (2000mm) Chapter 4 System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
E3750-61608 64-Conductor Cable E3750-61608 96-Pin, 64-Conductor to 96-Pin DIN Cable 66 System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
E3750-61612 2x1 Coax to 2x1 (Drain/Hi) Cable Coax 3x1 to 3x1 E3750-61612 1200mm ± 25mm Chapter 4 System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
68 Ribbon SUB-D to 3x1 E3750-61613 3000mm E3750-61613 Serial Interface Cable System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
Chapter 4 E3750-61614 High-Power Load Card Cable Individual Cable Detail E3750-61614 8-Channel Load Card Cable System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
70 E3750-61615 16-Channel High Power Load Card Cable Individual Cable Detail E3750-61615 16-Channel Load Card Cable System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
E3750-61621, E6170-61612 Male BNC Coax to 3x1 Isolated Instrument Cable Isolated Instruments BNC E3750-61621 (1200mm) E6170-61612 (2000mm) Chapter 4 System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
E3750-61624 30 Amp Load Card Cable E3750-61624 8-Channel Heavy Duty Load Card Cable 30A 72 System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
E3750-61625 24-Channel Medium Power Load Card Cable E3750-61625 24-Channel, Medium Power Load Card Cable Chapter 4 System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
Continued on next page E3750-61625 24-Channel Medium Power Load Card Cable (detail) E3750-61625 Continued 74 System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
E3750-61626 48-Channel Medium Power Load Card Cable Note: This cable Connects two 24-channel loadcards to the MAC panel. This cable is the recommended replacement part for ANY 24-channel MAC replacement cable. E3750-61626 Dual 24-Channel Load Card Cable Continued on next page Chapter 4 System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
E3750-61626 48-Channel Medium Power Load Card Cable part 2 E3750-61626 Continued 76 System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
E3750-61627 6628 Power Supply Cable E3750-61627 Power Supply Cable Chapter 4 System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
Pin Matrix Cable E3751-61601 (1016mm) E6170-61610 (1500mm) E3751-61601, E6170-61610 64-Conductor Twisted-Pair Cable 78 System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
E3857-61613 Rack On/Off Switch to PDU Cable E3857-61613 Rack On/Off Switch to PDU Cable Chapter 4 System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
E6170-61603 E6170-61603 E8792/93 to MAC Panel Cable 80 System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
1016mm E6170-61604 E8794 to Mac Panel or Express Connect and SLU Interconnect Cable Chapter 4 System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
E6170-61606 High Current Jumper E6170-61606 Power Bus Jumper Cable 82 System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
E6170-61609 External Power Cable (6653/6673) E6170-61609 External Power Cable (6653, 6673) Chapter 4 System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
E6170-61611 External Power Cable (6628/6643) E6170-61611 SLU to UUT Low Current Power Supply Cable (6628, 6643) 84 System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
E6170-61613 DAC to Pin Card Aux Cable E6170-61613 DAC to Pin Card Aux. Cable Chapter 4 System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
E6170-61615 E6170-61615 DAC to Custom Card Cable 86 System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
E6189-61600 Power Supply Power Cable E6189-61600 Power Supply Power Cable Chapter 4 System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
E6230-61603 Heavy-Duty Load Card Cable E6230-61603 Heavy-Duty Load Card Cable 88 System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
E6247-61601 Cable-Digitizer (E1563A) E6247-61601 1200mm Chapter 4 System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
E8770-61601 External Power Cable E8770-61601 External Power Cable 90 System Cables and Connectors Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
Chapter 5 System Diagnostics Chapter Contents This chapter has information to perform System Diagnostics and Service Diagnostics on the TS-5400 System. The chapter is separated as follows: • Support Strategy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • Diagnostics Strategy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • Using Agilent TestExec SL to Run the Testplan. . . . . . . . . .
AVERTISSEMENT Lors du dépannage, il est probable que des tensions pouvant causer des blessures ou la mort soient présentes. Le dépannage ne doit étre confié qu’à un personnel d’entretien qualifié. Caution To prevent electrostatic discharge (ESD): from damaging sensitive system components, always wear a grounded, anti-static wrist strap when working on the system Diagnostics Strategy Two diagnostic testplans were developed for your test system at the factory. Dgn.
Using Agilent TestExec SL to Run the Testplan Use TestExec SL to select and run the following testplan to perform the system diagnostics: C:\Program Files\Agilent\TS-5400 System Software\testplan\dgn\Dgn.tpa Executing the Testplan To Execute a testplan select ‘Debug’ then ‘Go’ or press F5 or press . Diagnostics will begin executing and report any errors it finds. Answer any questions as appropriate to continue execution.
Module Name 16 Module Description Name/Location of DLL used for the Module VXI Mainframe Number Location of Module in Mainframe Module’s Logical Address 0=No reset when sending a Global Reset 1=Resets when sending a Global Reset Figure 5-2. Typical Hardware Configuration 94 System Diagnostics Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
Test Execution Details The Test Execution Details query allows you to see the execution order and the actions used in a test sequence. This allows you to check and see if the correct tests are performed. Figure 5-3 shows a typical test sequence. 1. Click on “View” 2. Click on “Test Execution Details”. Figure 5-3. Test Execution Details (Actions in a Test) Chapter 5 System Diagnostics Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
96 System Diagnostics Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
Chapter 6 Calibration and Preventive Maintenance Calibration Overview Calibration is recommended for VXI modules or individual instruments on an annual basis. Typically this requires removing the VXI module(s) or instruments from the system for calibration. The Agilent E6171A/B Measurement Control Module is automatically adjusted by the system software. When the Agilent TestExec SL software is started, the automatic adjustment constants are down-loaded and the time stamp is checked.
System Adjustments Agilent E6171A/B Measurement Control Module adjustment must be done in the Agilent TS-5400 Test System where the E6171A/B module resides. Agilent E6171A/B specific measurement constants are stored in the PC controller as part of the TestExec SL software. A “soft” or system-wide adjustment can be done at any time. The TestExec SL software notifies you if 30 days have expired since the last system-wide adjustment.
Adjustment Procedure for Agilent E6171A Modules 1. Agilent E6171A modules require the simple calibration fixture shown in Figure 6-1. Build the test fixture by adding leads to an Agilent 0699-4532 resistor as shown. The resistor is a 100Ω, 0.1% tolerance, 4 Watt, low temperature coefficient precision resistor. Adding the extra leads allows for 4-Wire Ohms resistance measurements. Keep all lead lengths as short as possible. Figure 6-1. Agilent E6171A Calibration Fixture 2. When instructed by the ‘autoadj.
Figure 6-2. Installing the Calibration Fixture on an Agilent E6171A Measurement Control Module 3. Select the OK button in the prompt box. Note, if you select the CANCEL button, this portion of the Agilent E6171A calibration is not performed. 4. When prompted by the ‘autoadj.tpa’ testplan , remove the test fixture ribbon cable and reconnect the ribbon cable from the E6172A Matrix Module. 5. Select the OK button in the prompt box. 6. The ‘autoadj.
7. When prompted by the ‘autoadj.tpa’ testplan, adjust potentiometer R1961 (front panel of the Agilent E6171A module) until the red vertical bar is centered in the white segment of the measurement range. See Figure 6-3. Adjust R196 on the Agilent E6171A front panel until the red bar is centered in the white space. Figure 6-3. Typical Prompt Box to Adjust Potentiometer R196 on the Agilent E6171A Module 8. Select the OK button in the adjustment box.
10.Select the OK button in the adjustment box. Note: select the CANCEL button if you are unable to center the vertical bar. 11. System adjustment is complete. Adjustment Procedure for Agilent E6171B Modules Agilent E6171 Revision B Modules have the resistor standard built into the module; no test fixture is required. 1. Remove the 4" ribbon cable from the J2 connector on the front of the Agilent E6171B module. Fold and connect the ribbon cable to the J2 connector on the Agilent E6171B. See Figure 6-5.
2. Run the ‘autoadj.tpa’ testplan. 3. When prompted by the ‘autoadj.tpa’ testplan, adjust potentiometer R1961 (front panel of the Agilent E6171B module) to match the indicated reading. See Figure 6-3. 4. Select the OK button in the adjustment box. Note: select the CANCEL button if you are unable to center the vertical bar. 5. When prompted by the ‘autoadj.tpa’ testplan, adjust potentiometer R1971 (front panel of the Agilent E6171B module) to match the indicated reading. See Figure 6-4. 6.
AutoAdj Test Codes and Types The following are some of the codes that shows the mapping between the "test number" (ID) in auto adjust and what part of the Measurement Control Module was measured. Some of the acronyms used to identify the different parts of the MCM in Table 6-1. Use the acronyms to determine the part of the MCM was measured for troubleshooting purposes. Table 6-1.
Table 6-2. Parameter ID Numbers and Types ID # Chapter 6 Type Nominal Value Low Value High Value 30.52e-6 30.0e-6 31.0e-6 6 HVCI Gain 7 Comp200V Gain 1.848 1.75 2.05 8 Comp20V Gain 0.1848 0.175 0.205 9 LV ClampDac Gain 78.13e-3 0.065 0.09 10 HV ClampDac Gain 430.0e-3 0.30 0.55 11 Arb MDac Gain 7.723e-3 0.005 0.009 12 Arb Xfrm Gain 38.62e-3 0.025 0.050 13 LVCV Offset -19.77 -21.0 -18.5 14 HVCV Offset -110.0 -125.0 -105.0 15 LVCI 200m Offset -988.6e-3 -1.
Table 6-2. Parameter ID Numbers and Types ID # 106 Type Nominal Value Low Value High Value 36 DRFVMI HV20m 0.0 -0.5 0.9 37 AttnCalHigh Gain 0.051 0.049 0.053 38 AttnCalHigh Offset 2.40 2.25 2.55 39 AttnCalMid Gain 0.982 0.972 0.991 40 AttnCalMid Offset 0.0 -0.003 0.003 41 AttnCalLo Gain 0.051 0.049 0.053 42 AttnCalLo Offset -2.40 -2.55 -2.25 Calibration and Preventive Maintenance Artisan Technology Group - Quality Instrumentation ...
Verification Procedures Functional and Performance Verification procedures for the individual VXI modules and the power supplies are found in the respective module’s Service Manual. Chapter 6 Calibration and Preventive Maintenance Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
108 Calibration and Preventive Maintenance Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
Appendix A Test Capabilities and System Requirements Appendix Contents This appendix lists the test capabilities of the Agilent TS-5400 System, and the physical and electrical requirements to operate the system. This appendix is separated as follows: • Test Capabilities – Measurement Sample Methods . . . . . . . • System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • Miscellaneous Specifications . . . . . . . . . . . . . . . . . . . . . . . .
System Capability DC Accuracy Sample A simplified dc accuracy sample test, shown in Figure A-1, including numbered “offsets,” is used as an example. Every relay in the measurement path needs to be included in the algorithm for calculating the system-level capability. The source voltage of 12.5 volts is supplied by Power Supply #1 through the load card. The 1-year Accuracy vs. Aperture (±(% of reading + volts)) specification of the Agilent E1411B DMM for dc voltage on the 64-volt range for 16.
Figure A-1. DC Voltage Accuracy and Driver Saturation Test Capability Example Appendix A Test Capabilities and System Requirements Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
System Capability Driver Current Leakage Sample The system capability output driver current leakage test uses the Agilent E6171 Measurement Control Module Force Voltage, Measure Current functionality. As shown in Figure A-2, the DvmHi input is connected through a disconnect relay to the V/I source. The output of the V/I source is connected through ABus4 and the Agilent E6172A 32-Pin Matrix Module row 32.
Figure A-2. Output Driver Saturation Capability Sample Appendix A Test Capabilities and System Requirements Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
System Requirements The approximate weight of a fully-loaded two-VXI mainframe system with one Agilent 6673A power supply is 350 kilograms (750 pounds) or 400 kilograms (900 pounds) including the pallet and all included material (the pallet weighs approximately 50 kilograms (110 pounds)), and manuals, etc. account for the remaining weight). Anti-Static Surface Static electricity is destructive to your production process and your Agilent TS-5400 Test System.
Air Quality Requirements As a rule, good air quality is as important for the reliability of your Agilent TS-5400 system as it is for your production process. Three types of airborne contaminants are discussed below. The presence of any of these contaminants at the site will contribute to system degradation, resulting in lower reliability and higher operating costs. Corrosive Contaminants Corrosion is a complex form of material deterioration or destruction by chemical or electrochemical reaction.
system to recover before powering up. 116 Test Capabilities and System Requirements Appendix A Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
Miscellaneous Specifications Acoustic Noise LpA ≤60dB am Arbeitsplatz normaler Betrieb nach EN27779: 1991 ac Power Over-voltage Category Category III Pollution Degree Degree 2 (IEC 664) Electromagnetic Compatibility Requirements The Agilent TS-5400 Test System complies with EN 55011 (CISPR 11) Group 1, Class A for conducting emissions. The product exceeds the EN 55011 (CISPR 11) Group 1, Class A limit for radiated emissions by less than 10 dB when measured on a test site at a distance of 30 meters.
Figure A-3. Electromagnetic Compatibility Calculation Illustration 118 Test Capabilities and System Requirements Appendix A Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
Appendix B Parts Lists Appendix Contents This appendix lists the system-level replaceable parts for the Agilent TS-5400 System. The appendix is separated as follows: • Identifying and Ordering Parts . . . . . . . . . . . . . . . . . . . . . . . • Replaceable Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • Recommended Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 6-3. E8780B/E8786B Replaceable Parts Part Number Description Advantech Industrial PC Components (850 MHz) 0960-2282 0950-4396 0950-4395 3160-4160 0950-4345 0950-2656 0950-4407 1818-8888 Single board computer PC Backplane Power Supply Fan CD ROM Drive 3.5" Floppy Drive 40GB Hard Disk Drive Memory (256 MB) Monitors E8770-80702 15 inch Flat Panel Service Replacement Kit Includes required sheet metal for mounting the monitor.
Table 6-3.
Table 6-3.
Table 6-3. E8780B/E8786B Replaceable Parts Part Number Description Serial Communication E6170-66002 Serial Protocol Adapter (Multicom III) E6249-80005 Rocket Port Serial Card Appendix B Parts Lists Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
Recommended Spare Parts Table 6-4. E8780B/E8786B Recommended Spare Parts Part Number 124 Description Qty.
Glossary 2x1 A single-conductor cable with a shield return. See the Measurement Control Module instrumentation cabling diagrams in Chapter 4, “System Cables and Connectors” on page 63. 3x1 A twinax (2) conductor cable with a shield. See the Measurement Control Module instrumentation cabling diagrams in Chapter 4, “System Cables and Connectors” on page 63. 5x1 Multiplexing Refers to the four-channel ABus and the single-channel DUT (Device Under Test) Common ground. A ABus Acronym for Analog Bus.
ADC Acronym for Analog to Digital Converter. See Digitizer. ADC1Hi and ADC1Lo Differential input to ADC channel 1 from Measurement Control module J3, rows 7 and 8 respectively. ADC2Hi and ADC2Lo Differential input to ADC channel 2 from Measurement Control module J3, rows 9 and 10, respectively. Adjustment An adjustment is an action performed in the field to modify an instrument's response to some input. It can usually be performed by the user on-site. Alias An alternate name for an item.
C Calibration A standardized maintenance procedure designed to ensure system accuracy. In this manual it refers to removing those items that require calibration the DVM and the Frequency Counter and shipping them to an Agilent bench site for calibration. Card As used in this manual, refers to printed circuit boards that are not installed VXI mainframes. See module. Column Disconnect Relay A series relay on each of the four lines of the ABus that can be controlled either automatically or manually.
D DAC Digital to Analog Converter - Converts a digital signal to an analog signal. Datalogging The process of collecting data about tests when the test plan runs. Subsequent study of this data can aid you in improving the processes associated with manufacturing and testing. Debug Panel On the front panel of the TS-5400 system there is a test point for each ABus column (four total). These test points allow monitoring the bus status during troubleshooting operations.
Exception An error that occurs during testing. For example, if an instrument that is supposed to make a measurement “times out” before returning a reading, an exception has occurred. Expander Block Provides various configurations of screw terminals. There are two types of expander blocks currently used on the TS-5400 mass interconnect: • 4 Terminal Expander Block: This is a four-screw terminal block. All four connection points are common.
Flyback Protection Device Any device that controls the magnitude of positive or negative-going voltage spikes on a channel. Flyback Voltage The voltage surge experienced when current flow through a coil is abruptly stopped or started. Form C Relay Standard terminology for Single-Pole, Double Throw (SPDT) relay contacts. Functional Test A test that simulates the actual operating conditions of the Device Under Test (DUT). G Glitch An unexpected or unplanned event or occurrence.
HV Interlock High Voltage Interlock interrupt that disables the high voltage amplifier of the Measurement Control module. I ICA Interface Connector Assembly - The system half of the mass interconnect. May also be called the receiver or fixture receiver. Interface Connector Blocks The connectors between the ICA and the ITA. Instrument Handler An additional layer of software between Agilent TestExec SL and a device driver.
ITA Interface Test Assembly - The DUT half of the mass interconnect. It is the base of the test fixture. J Jumper Comb A comb-shaped shorting bar with a plastic covering over the metal spine of the comb. It is used to jumper together some or all the NO or NC terminals on a load card. K Keyword An identifier used to restrict the number of matches found when searching for a specific item.
provide a two level card ID; card type, and load configuration ID. Load Switching A load that can be switched in or out of a power supply circuit on command. M MAC Panel Mass interconnect panel marketed by Agilent. Mass Interconnect The main connection panel for connecting the test system to the test fixture. The mass interconnect consists of an ICA (Interface Connector Assembly), on the system side, and an ITA (Interface Test Assembly) on the test fixture side.
at a certain predetermined voltage. Multiplex A more restricted version of a matrix. Any row relay can be connected to any column but only one can be connected at a time. Multiplexed Detectors And Sources This consists of the E6171A Measurement Control Module, the 32- Pin Switching Cards, and assorted GPIB or VXIbus based instruments and detectors.
One-shot Mode The Measurement Control Module (MCM) has an internal timer/counter that is primarily used to time the open/close of the MCM relays. It can also be used as a trigger source. As a trigger it can either in either of two modes; it can run continuously, or it can be set to generate a single, or one-shot, pulse. Open All Relays A command that immediately opens all the relays, both columns and rows, on a module.
R Receiver See ICA. Relay Sequencing The process of ensuring relay switching has fully completed before continuing a test action. A “busy bit”, or status bit, generated by each load card when its relays are switched halts further test actions until the relay timer has timed out. This allows the slowest relay on a card to complete opening/closing before continuing a test action. This feature is not implemented in TestExec SL software release A.01.00. The timing is controlled by the PC.
S SCPI Acronym for: Standard Commands for Programmable Instruments Safety Shroud A cover for the DUT that protects personnel from possible contact with dangerous voltages on the DUT. The shroud should be physically connected to a NO (normally Open) safety switch that is closed only when the shroud is in place. The switch is wired across the two interlock pins on J3 of the Measurement Control Module. These pins are wired to 1A13 and 1A15 of the ITA.
Switch Path A connection between nodes needed to make a test. For example, a switch path might connect the output from a power supply to a pin on the unit under test. Example: (FuncGen-SrcBus-Dvm-MeasBus) In the example, the source bus of the function generator is connected to the measurement bus of the digital voltmeter when the switch path is closed. Switching Configuration Editor A software tool used to define topology.
Test Limits The acceptable boundaries for a test. If the results from a test are less than the lower limit or greater than the upper limit, the test fails. A test can have more than one set of limits, where each set is associated with a named variant, such as “Hot” or “Cold.” Test Executive A software tool used to develop tests, assemble them into a testplan, and run the testplan. Test A sequence of actions executed as a group to do some form of test.
Information defined at the DUT layer includes: • Definitions of convenient aliases for test points on the DUT, such as “TP1.” U Unit Under Test (UUT) The automotive module or printed circuit board being tested. Also known as Device Under Test (DUT) UUT Common A fifth column alongside the ABus in the Measurement Control Module and 32-Pin Matrix Module that connects to the UUT common.
VCC Refers to the semiconductor component's supply voltage. Vload The voltage measured at the load under test, ignoring cabling losses. VME Computer backplane architecture standard. VXI Computer backplane architecture standard that incorporates both the VMEbus and GPIB communications features. W Wire A bus or other connection in the topology. Glossary Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
142 Glossary Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
Index Numerics 32-Channel Event Detector, 27 32-Pin Matrix Module, 20 Agilent E6187A Power Supply, 29 Agilent E6188A Power Supply, 29 Agilent E6189A Power Supply, 29 Agilent TestExec SL Software customizing, 54 A Accommodate Additional Instrumentation, 54 Accuracy system DC, 110 ADC (Digitizer) VXI Technology E1563A, 39 Adding GPIB instruments, 52 optional switch modules, 54 Address logical, 32 Adjustment Procedure for Agilent E6171A Modules, 99 Adjustment Procedure for Agilent E6171B Modules, 102 A
E3750-61625, E3750-61626, E3750-61627, E3751-61601, E3857-61613, E6170-61603, E6170-61604, E6170-61606, E6170-61609, E6170-61610, E6170-61611, E6170-61612, E6170-61613, E6170-61614, E6170-61615, E6189-61600, E6230-61603, E6247-61601, E8770-61601, 73 75 77 78 79 80 81 82 83 78 84 71 85 65 86 87 88 89 90 Calibration Overview, 97 Conceptual Block Diagram, 15 Configuration mass interconnect, 23 Configuring additional GPIB Instruments, 52 Connecting Instrument Input(s) to the Measurement Control Module, 53 Co
G standard functions, 59 General Guidelines system customization, 55 Glossary, 125 GPIB Addresses instruments, 31 GPIB Instrument Locations, 31 GPIB Instrument Locations And Addresses, 31 GPIB Instruments, installing additional, 52 GPIB) Addresses power supplies, 31 Instrument Reset, 57 Instrument Reset Management, 57 Instruments GPIB addresses, 31 Interface Connector Adapter (ICA), 23 Interface Test Adapter (ITA), 23 Invoke reset on instrument, 57 reset on modules, 57 ITA, 23 J H Jumper Settings
Agilent E1411B, 26, 36 Multiplexed Instruments, 25 instrument, 57 instrument management, 57 Reset Invocation, 57 Reset Routine N Naming Conventions, 61 instrument handlers, 61 module handlers, 61 specifying, 57 S Settings switch and jumper, 34 O Optional Switch Modules installing, 54 Options Rack, 11 Ordering Parts, 119 Overview calibration, 97 system, 14 P Agilent TestExec SL, 14 system, 14 Specifications, 109 Specifying a Reset Routine, 57 Specifying a Reset Routine Using the System Configurat
System.
148 Index Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment • FAST SHIPPING AND DELIVERY • TENS OF THOUSANDS OF IN-STOCK ITEMS • EQUIPMENT DEMOS • HUNDREDS OF MANUFACTURERS SUPPORTED • LEASING/MONTHLY RENTALS • ITAR CERTIFIED SECURE ASSET SOLUTIONS SERVICE CENTER REPAIRS Experienced engineers and technicians on staff at our full-service, in-house repair center WE BUY USED EQUIPMENT Sell your excess, underutilized, and idle used equipment We also offer credit for buy-back
