Technical data

ManualsBrandsAgilent Technologies ManualsConsumer electronics6224B

Visit our web site

http://www.agilent.com/find/power

(at 0˚ to 55˚ C unless otherwise specified)

6571A 6572A 6573A 6574A 6575A

Output ratings Output voltage 0 to 8 V 0 to 20 V 0 to 35 V 0 to 60 V 0 to 120 V

Output current 0 to 220 A 0 to 100 A 0 to 60 A 0 to 35 A 0 to 18 A

Programming accuracy Voltage 0.04% + 8 mV 20 mV 35 mV 60 mV 120 mV

at 25˚C ±5˚C Current 0.1% + 125 mA 60 mA 40 mA 25 mA 12 mA

Ripple and noise Voltage rms 650 µV 750 µV 800 µV 1.25 mV 1.9 mV

from 20 Hz to 20 MHz peak-peak 7 mV 9 mV 9 mV 11 mV 16 mV

Current rms 200 mA 100 mA 40 mA 25 mA 12 mA

Load regulation or Voltage 0.002%+ 300 µV 650 µV 1.2 mV 2 mV 4 mV

Line regulation Current 0.005%+ 10 mA 7 mA 4 mA 2 mA 1 mA

Transient Less than 900 µs for the output voltage to recover 100 mV following a change in load from

response time 100% to 50% or 50% to 100% of the output current rating of the supply

Supplemental Characteristics (Non-warranted characteristics determined by design and useful in applying the product)

Average resolution Voltage 2 mV 5 mV 9 mV 15 mV 30 mV

Current 55 mA 25 mA 15 mA 8.75 mA 4.5 mA

OVP 15 mV 35 mV 65 mV 100 mV 215 mV

Output voltage

*Full load programming rise/fall time 30 ms 60 ms 130 ms 130 ms 195 ms

programming (10% to 90% or 90% to 10%) with full

response time* resistive load equal to rated output

voltage/rated output current.

SPECIFICATIONS

Constant-voltage, constant-current operation

Complete front-panel control calibration and display

Remote programming and sensing

Fan-speed control to minimize acoustic noise

Low ripple and noise

Over-voltage and over-current protection

dc Floating Voltage: Output terminals can be floated up to ±240 Vdc

from chassis ground

Output Common-Mode Noise Current: (to signal ground binding post)

500 µA rms, 4 mA peak-to-peak

Remote Sensing: Up to half the rated output voltage can be dropped

in each load lead. The drop in the load leads subtracts from the

voltage available for the load.

Modulation: (Analog programming of output voltage and current)

Input Signal: 0 to –4 V for voltage, 0 to 7 V for current

Input Impedance: 30 k Ohm or greater

Input Power: 3,800 VA, 2,600 W at full load; 170 W at no load

Regulatory Compliance: Listed to UL1244; certified to CSA556B;

conforms to IEC 61010-1. See page 73 for more information.

Size: 425.5 mm W x 132.6 mm H x 640 mm D

(16.75 in x 5.22 in x 25.2 in)

See page 55 for more details

Ordering Information

STANDARD: 191 to 250 Vac, 47 to 63 Hz

Opt 200 174 to 220 Vac, 47 to 63 Hz (Japan only)

*Opt 908 Rack-mount Kit (p/n 5062-3977)

*Opt 909 Rack-mount Kit w/ Handles(p/n 5063-9221)

Opt 910 Service Manual and extraOperating Guide

and Programming Guide

A line cord option must be specified.

See pages 48-51 for ordering information.

*Support rails required

CCESSORIES

p/n 1494-0059 Accessory Slide Kit $000

E3663AC Support rails for Agilent rack cabinets

Weight: Net, 28.2 kg (62 lb); shipping, 31.8 kg (70 lb)

Warranty Period: Three years

30 AGILENT dc POWER SUPPLIES

Single-Output Manually Controlled: 2000 W

6571A

6572A

6573A

6574A

6575A

Manually

Controlled

6571A-6575A