Specifications

Function Range
2
Frequency, etc. 1 Year
2
23°C ± 5°C
DC Voltage 100.0000 mV – 0.0050 + 0.0040
1.000000 V – 0.0040 + 0.0007
10.00000 V – 0.0035 + 0.0005
100.0000 V – 0.0045 + 0.0006
300.000 V – 0.0045 + 0.0030
True RMS AC Voltage
3
100.0000 mV to 100.0000 V 3 Hz – 5 Hz 1.00 + 0.04
5 Hz – 10 Hz 0.35 + 0.04
10 Hz – 20 kHz 0.06 + 0.04
20 kHz – 50 kHz 0.12 + 0.05
50 kHz – 100 kHz 0.60 + 0.08
100 kHz – 300 kHz
4
4.00 + 0.50
300.0000 V 3 Hz – 5 Hz 1.00 + 0.08
5 Hz – 10 Hz 0.35 + 0.08
10 Hz – 20 kHz 0.06 + 0.08
20 kHz – 50 kHz 0.12 + 0.12
50 kHz – 100 kHz 0.60 + 0.20
100 kHz – 300 kHz
4
4.00 + 1.25
Resistance
5
100.0000 Ω 1 mA current source 0.010 + 0.004
1.000000 kΩ 1 mA 0.010 + 0.001
10.00000 kΩ 100 µA 0.010 + 0.001
100.0000 kΩ 10 µA 0.010 + 0.001
1.000000 MΩ 5.0 µA 0.010 + 0.001
10.00000 MΩ 500 nA 0.040 + 0.001
100.0000 MΩ 500 nA 10 MΩ 0.800 + 0.010
Frequency and Period
6
100 mV to 300 V 3 Hz – 5 Hz 0.10
5 Hz – 10 Hz 0.05
10 Hz – 40 Hz 0.03
40 Hz – 300 kHz 0.01
DC Current 10.00000 mA <0.1 V burden 0.050 + 0.020
(34901A only) 100.0000 mA <0.6 V 0.050 + 0.005
1.000000 A <2 V 0.100 + 0.010
True RMS AC Current 10.00000 mA to 1.00000 A 3 Hz – 5 Hz 1.00 + 0.04
(34901A only) 5 Hz – 10 Hz 0.30 + 0.04
10 Hz – 5 Hz 0.10 + 0.04
100.0000 mA
7
3 Hz – 5 Hz 1.00 + 0.5
5 Hz – 10 Hz 0.30 + 0.5
10 Hz – 5 kHz 0.10 + 0.5
Temperature Type 1-Year Accuracy
8
Thermocouple
9
B 1100°C to 1820°C 1.2°C
E -150°C + 1000°C 1.0°C
J -150°C + 1200°C 1.0°C
K -100°C + 1200°C 1.0°C
N -100°C + 1300°C 1.0°C
R 300°C + 1760°C 1.2°C
S 400°C + 1760°C 1.2°C
T -100°C + 400°C 1.0°C
RTD R
0
from 49 Ω to 2.1 kΩ -200°C + 600°C 0.06°C
Thermistor 2.2 k, 5 k and 10 k -80°C to 150°C 0.08°C
See manual or datasheet for more information
145
Switching
For test applications that don’t
require the built-in measurements
of the 34970A, the unit can be
ordered without the internal DMM.
This provides an ultra low-cost
solution for routing test signals to
and from your device-under-test
and assorted instruments, including
external DMMs, scopes, counters
and power supplies. Plus, you can
add the DMM later if your needs
change.
Low-Cost Data Acquisition/Switch 34970A (Continued)
More detailed specifications at www.agilent.com/find/34970A
Data Acquisition & Switching
Accuracy Specifications
1
±(% of reading + % of range)
Includes measurement error, switching error and transducer conversion error
1
Specifications are for 1-hour warm-up and
6
1
/
2
digits, slow AC filter.
2
20% over range on all ranges except 300 Vdc and
AC ranges and 1 A DC and AC current ranges.
3
For sinewave input >5% of range. For inputs from
1% to 5% of range and <50 kHz, add 0.1% of range
additional error.
4
Typically 30% of reading error at 1 MHz, limited
to 1 x 10
8
V Hz.
5
Specifications are for 4-wire ohms function or
2-wire ohms using scaling to remove the offset.
Without scaling, add 4 Ω additional error in
2-wire ohms function.
6
Input >100 mV. For 10 mV inputs, multiply %
of reading error x 10.
7
Specified only for inputs >10 mA.
8
For total measurement accuracy,
add temperature probe error.
9
Thermocouple specifications not guaranteed when
34907 module is present