User`s guide
Table Of Contents
- Title Page
- Contents
- Getting Started
- Introduction and Measurement
- Phase Noise Basics
- Expanding Your Measurement Experience
- Starting the Measurement Software
- Using the Asset Manager
- Using the Server Hardware Connections to Specify the Source
- Setting GPIB Addresses
- Testing the 8663A Internal/External 10 MHz
- Testing the 8644B Internal/External 10 MHz
- Viewing Markers
- Omitting Spurs
- Displaying the Parameter Summary
- Exporting Measurement Results
- Absolute Measurement Fundamentals
- Absolute Measurement Examples
- Residual Measurement Fundamentals
- What is Residual Noise?
- Assumptions about Residual Phase Noise Measurements
- Calibrating the Measurement
- Measurement Difficulties
- Residual Measurement Examples
- FM Discriminator Fundamentals
- FM Discriminator Measurement Examples
- AM Noise Measurement Fundamentals
- AM Noise Measurement Examples
- Baseband Noise Measurement Examples
- Evaluating Your Measurement Results
- Advanced Software Features
- Reference Graphs and Tables
- Approximate System Noise Floor vs. R Port Signal Level
- Phase Noise Floor and Region of Validity
- Phase Noise Level of Various Agilent Sources
- Increase in Measured Noise as Ref Source Approaches DUT Noise
- Approximate Sensitivity of Delay Line Discriminator
- AM Calibration
- Voltage Controlled Source Tuning Requirements
- Tune Range of VCO for Center Voltage
- Peak Tuning Range Required by Noise Level
- Phase Lock Loop Bandwidth vs. Peak Tuning Range
- Noise Floor Limits Due to Peak Tuning Range
- Tuning Characteristics of Various VCO Source Options
- 8643A Frequency Limits
- 8644B Frequency Limits
- 8664A Frequency Limits
- 8665A Frequency Limits
- 8665B Frequency Limits
- System Specifications
- System Interconnections
- PC Components Installation
- Overview
- Step 1: Uninstall the current version of Agilent Technologies IO libraries
- Step 2: Uninstall all National Instruments products.
- Step 3: Install the National Instruments VXI software.
- Step 4: Install the National Instruments VISA runtime.
- Step 5: Install software for the NI Data Acquisition Software.
- Step 6: Hardware Installation
- Step 7. Finalize National Instruments Software Installation.
- Step 8: System Interconnections
- Step 9: Install Microsoft Visual C++ 2008 Redistributable Package use default settings
- Step 10: Install the Agilent I/O Libraries
- Step 11: Install the E5500 Phase Noise Measurement software.
- Step 12: Asset Configuration
- Step 13: License Key for the Phase Noise Test Set
- Overview
- PC Digitizer Performance Verification
- Preventive Maintenance
- Service, Support, and Safety Information
- Safety and Regulatory Information
- Safety summary
- Equipment Installation
- Environmental conditions
- Before applying power
- Ground the instrument or system
- Fuses and Circuit Breakers
- Maintenance
- Safety symbols and instrument markings
- Regulatory Compliance
- Declaration of Conformity
- Compliance with German noise requirements
- Compliance with Canadian EMC requirements
- Service and Support
- Return Procedure
- Safety and Regulatory Information
AM Noise Measurement Examples
12
Agilent E5505A User’s Guide 313
Table 48 Parameter data for the AM noise using an N5500A Option 001
Step Parameters Data
1 Type and Range Tab
•
Measurement Type
•
Start Frequency
•
Stop Frequency
•
Averages
•
FFT Quality
•
Swept Quality
•
AM Noise
•
10 Hz
•
100 E + 6 Hz
•
4
•
Fast
•
Fast
2Sources Tab
•
Carrier Source Frequency
•
Carrier Source Power
•
Carrier Source Output is
connected to:
•
Detector Input Frequency
•
600 E + 6 Hz
•
20 dBm
•
Test Set
•
600 E +6 Hz
3Cal Tab
•
Detector Constant
•
Known Spur Parameters
•
Offset Frequency
•
Amplitude
•
Use internal automatic self-calibration
•
1 Hz
•
-130 dBc
4 Block Diagram Tab
•
Source
•
AM Detector
•
Down Converter
•
Manual
•
Test Set AM Detector
•
None
5Test Set Tab
•
Input Attenuation
•
LNA Low Pass Filter
•
LNA Gain
•
Detector Maximum Input Levels
Microwave Phase Detector
RF Phase Detector
AM Detector
•
Ignore out-of-lock conditions
•
Pulsed Carrier
•
DC Block
•
Analyzer View
•
PLL Integrator Attenuation
•
Auto checked
•
Auto checked
•
Auto Gain
•
0 dBm
•
0 dBm
•
0 dBm
•
Not checked
•
Not checked
•
Not checked
•
Baseband
•
0.00 dBm
6Downconverter Tab Does not apply to this measurement example.