User`s guide

ManualsBrandsAgilent Technologies ManualsConsumer electronics6111A

101

102

103

104

105

106

107

108

109

110

Table Of Contents

Title Page
- Notices
Contents
Getting Started
- Introduction
- Documentation Map
- Additional Documentation
- System Overview
Introduction and Measurement
- Introducing the GUI
- Designing to Meet Your Needs
  - Beginning
- E5505A Operation: A Guided Tour
  - Required equipment
  - How to begin
- Powering the System On
  - To power on a racked system
  - To power on a benchtop system
- Starting the Measurement Software
- Performing a Confidence Test
- Powering the System Off
Phase Noise Basics
- What is Phase Noise?
  - Phase terms
    - Spurious signals
    - Phase noise
Expanding Your Measurement Experience
- Starting the Measurement Software
- Using the Asset Manager
  - Configuring an asset
- Using the Server Hardware Connections to Specify the Source
- Setting GPIB Addresses
  - To change the GPIB address
- Testing the 8663A Internal/External 10 MHz
- Testing the 8644B Internal/External 10 MHz
- Viewing Markers
- Omitting Spurs
- Displaying the Parameter Summary
- Exporting Measurement Results
Absolute Measurement Fundamentals
- The Phase-Lock-Loop Technique
  - Understanding the Phase-Lock-Loop Technique
  - The Phase-Lock-Loop Circuit
- What Sets the Measurement Noise Floor?
  - The System Noise Floor
  - The Noise Level of the Reference Source
- Selecting a Reference
- Estimating the Tuning Constant
- Tracking Frequency Drift
  - Evaluating beatnote drift
    - Action
- Changing the PTR
  - The Tuning Qualifications
    - Voltage controlled oscillators
    - Signal generators
- Minimizing Injection Locking
  - Adding Isolation
  - Increasing the PLL Bandwidth
- Inserting a Device
  - An attenuator
  - An amplifier
- Evaluating Noise Above the Small Angle Line
  - Determining the Phase-Lock-Loop bandwidth
    - Observing the beatnote
    - Measurement options
Absolute Measurement Examples
- Stable RF Oscillator
- Free-Running RF Oscillator
- RF Synthesizer Using DCFM
- RF Synthesizer Using EFC
- Microwave Source
Residual Measurement Fundamentals
- What is Residual Noise?
  - The noise mechanisms
    - Additive noise
    - Multiplicative noise
- Assumptions about Residual Phase Noise Measurements
  - Frequency translation devices
- Calibrating the Measurement
- Measurement Difficulties
  - System connections
Residual Measurement Examples
- Amplifier Measurement Example
FM Discriminator Fundamentals
- The Frequency Discriminator Method
  - Basic theory
  - The discriminator transfer response
    - System sensitivity
    - Optimum sensitivity
FM Discriminator Measurement Examples
- Introduction
- FM Discriminator Measurement using Double-Sided Spur Calibration
- Discriminator Measurement using FM Rate and Deviation Calibration
AM Noise Measurement Fundamentals
- AM-Noise Measurement Theory of Operation
  - Basic noise measurement
  - Phase noise measurement
- Amplitude Noise Measurement
  - AM noise measurement block diagrams
  - AM detector
    - AM detector specifications
    - AM detector considerations
- Calibration and Measurement General Guidelines
- Method 1: User Entry of Phase Detector Constant
  - Method 1, example 1
  - Method 1, example 2
- Method 2: Double-Sided Spur
  - Method 2, example 1
  - Method 2, example 2
- Method 3: Single-Sided Spur
AM Noise Measurement Examples
- AM Noise with N5500A Option 001
Baseband Noise Measurement Examples
- Baseband Noise with Test Set Measurement Example
- Baseband Noise without Test Set Measurement Example
Evaluating Your Measurement Results
- Evaluating the Results
  - Looking for obvious problems
  - Comparing against expected data
    - The device under test
    - The reference source
- Gathering More Data
  - Repeating the measurement
  - Doing more research
- Outputting the Results
  - Using a printer
- Graph of Results
  - Marker
- Omit Spurs
  - Parameter summary
- Problem Solving
Advanced Software Features
- Introduction
- Phase-Lock-Loop Suppression
  - PLL suppression parameters
- Ignore-Out-Of-Lock Mode
- PLL Suppression Verification Process
- Blanking Frequency and Amplitude Information on the Phase Noise Graph
  - Security level procedure
Reference Graphs and Tables
- Approximate System Noise Floor vs. R Port Signal Level
- Phase Noise Floor and Region of Validity
- Phase Noise Level of Various Agilent Sources
- Increase in Measured Noise as Ref Source Approaches DUT Noise
- Approximate Sensitivity of Delay Line Discriminator
- AM Calibration
- Voltage Controlled Source Tuning Requirements
- Tune Range of VCO for Center Voltage
- Peak Tuning Range Required by Noise Level
- Phase Lock Loop Bandwidth vs. Peak Tuning Range
- Noise Floor Limits Due to Peak Tuning Range
- Tuning Characteristics of Various VCO Source Options
- 8643A Frequency Limits
- 8644B Frequency Limits
- 8664A Frequency Limits
- 8665A Frequency Limits
- 8665B Frequency Limits
System Specifications
- Specifications
- Power Requirements
System Interconnections
- Making Connections
- System Connectors
- System Cables
- Connecting Instruments
PC Components Installation
- Overview
PC Digitizer Performance Verification
- Verifying PC Digitizer Card Output Performance
  - Required equipment
- PC Digitizer Card Input Performance Verification
  - Required equipment
Preventive Maintenance
- Using, Inspecting, and Cleaning RF Connectors
- General Procedures and Techniques
  - Connector Removal
- Instrument Removal
- Instrument Installation
Service, Support, and Safety Information
- Safety and Regulatory Information
- Service and Support
  - Agilent on the Web
- Return Procedure
  - Determining your instrument’s serial number
  - Shipping the instrument

102 Agilent E5505A User’s Guide

Expanding Your Measurement Experience

Exporting Trace Data

On the File menu, point to Export Results, then click on Trace Data. See

Figure 67 on page 102.

Figure 67 Trace data results

e5505a_user_trace_data_results

24 Jun 04 rev 3