Technical data

94
Choosing ac Line Voltage and Cord
Options for your Power Product
Power distribution systems, regula-
tions, and connection techniques
vary greatly among geographic
regions as a result of local ac
electrical standards. Most Agilent
products, including power products
which draw less than 500 watts
of power from the ac line, can be
readily adjusted to accept different
line voltages or frequencies.
Line voltage and frequency for
certain Power Products may not
be field changeable. Choosing the
correct voltage option for these
products requires care. This is
especially true for higher power
products. Line voltage/frequency
options and method of change are
summarized in Table 1a below.
Voltages for Europe and Asia Pacific
vary widely from country to country.
Europe is moving toward harmo-
nization, with countries standardiz-
ing on 230 Vac instead of 220 or
240 Vac. Some older products don’t
offer a 230 Vac option. For countries
operating on 230 Vac, option 240
with a range of +6%/-13% (a range of
208 to 254 Vac) generally offers the
best match. See table 1b for further
information. The specifications
listed for each product indicate the
range of voltage and frequency that
each option accomodates. If in
doubt, contact your local Agilent
Field Engineer for assistance.
Choosing ac Line Voltage and Cord Options for your
Agilent Power Products
(Continued)
Power Products Catalog 2002-2003 For more detailed specifications see the product manual at www.agilent.com/find/power
Agilent Technologies
Model Standard Line Voltage 50 HZ Field Changeable; Line Cord
Number Line Voltage Options Operation Method Series
6010A, 6011A, 120 220, 240 Yes Yes; internal board mounted 800
6012A, 6015A switch and quick connect jumpers
6030A, 6031A, 120 100*, 220, Yes Yes; internal board mounted switch 800
6032A, 6035A 240 and quick connect jumpers
6033A, 6038A 120 100*, 220, Yes Yes; internal board mounted switch 900
240 and quick connect jumpers
6060B, 6063B 120 100*, 220, 240 Yes Yes; internal switches 900
654XA 120 100, 220, 240 Yes Yes; internal board mounted switches 900
655XA 120 100, 220, 240 Yes Yes; internal quick connect jumpers 900
657XA 230 200* Yes Yes; internal board mounted switch 800
66000A 100-240 none Yes Not necessary; automatic wide ranging input 800
6610XA 100-120, none Yes Yes; bottom panel switch n.a.
200-240
661XC 120 100, 220, 230 Yes Yes; internal quick connect jumpers 900
662XA 120 100, 220, 240 Yes Yes; moveable insert on rear panel 900
mounted line cord module
663XXA 120 100, 220, 230 Yes Yes; internal quick connect jumpers 900
663XB 120 100, 220, 230 Yes Yes; internal quick connect jumpers 900
664XA 120 100, 220, 240 Yes Yes; internal board mounted switch 900
665XA 120 100, 220, 240 Yes Yes; internal quick connect jumpers 900
667XA, E4356A 230 200 Yes Yes; internal board mounted switch 800
668XA, 669XA 220 3Ø 400 3Ø Yes Yes; internal connector 3Ø;
unter-
mounted jumpers minated only
6811B 120 100, 230 Yes Yes; internal connector 900
mounted jumpers
6812B 120 100, 230 Yes Yes; internal connector 800
mounted jumpers
6813B 230 200 Yes Yes; internal connector 800
mounted jumpers
E3610A, E3611A, ØEM (115) ØE3 (230 V), Yes NO! Transformer change required; line cord
E3612A ØE9 (100 V) return to factory hardwired
E3614A, E3615A, ØEM (115) ØE3 (230 V), Yes Yes; internal board mounted switch
E3616A, E3617A, ØE9 (100 V)
E3620A, E3630A
E3631A, E3632A,
ØEM (115) ØE3 (230 V), Yes Yes: moveable insert on rear panel
E3633A, E3634A ØE9 (100 V) mounted ac receptacle
E364XA ØEM (115) ØE3 (230 V), Yes Yes, internal board mounted switch
ØE9 (100 V)
N3300A, N3301A 100-240 None Yes Not necessary; automatic 900
wide ranging input
Notes: 100*, 200*: for Japan only; derating required, product see specifications
Table 1A– ac Line Voltage/Frequency Options