Specifications

376 Index
Index
[:SENSe]:CORRection1:COLLect[:ACQuire]:DC, 245
[:SENSe]:CORRection1:COLLect[:ACQuire]:RF, 246
[:SENSe]:CORRection1:COLLect:SAVE, 246
[:SENSe]:CORRection2:CKIT, 247
[:SENSe]:CORRection2:CKIT:LIST[:STATe], 247
[:SENSe]:CORRection2:CKIT:STANdard1:DC, 248
[:SENSe]:CORRection2:CKIT:STANdard1:LIST, 249
[:SENSe]:CORRection2:CKIT:STANdard2:DC, 250
[:SENSe]:CORRection2:CKIT:STANdard2:LIST, 251
[:SENSe]:CORRection2:COLLect[:ACQuire], 252
[:SENSe]:CORRection2:COLLect[:ACQuire]:DC, 253
[:SENSe]:CORRection2:COLLect[:ACQuire]:RF, 254
[:SENSe]:CORRection2:COLLect:OPEN[:STATe], 254
[:SENSe]:CORRection2:COLLect:SAVE, 255
[:SENSe]:CORRection2:COLLect:SHORt[:STATe], 255
[:SENSe]:CORRection2:FIXTure, 256
[:SENSe]:CORRection2:FIXTure:EDELay:DISTance, 257
[:SENSe]:CORRection2:FIXTure:LABel, 258
:SOURce:LIST, 294
:SOURce:LIST:CLEar, 295
:SOURce:LIST:POINt, 295
:SOURce:LIST:RDC, 296
:SOURce:LIST:RDC:AVERage, 311
:SOURce:LIST:RDC:OFSCancel, 296
:SOURce:LIST:SIZE?, 296
:SOURce:LIST:STATe, 297
:SOURce:LIST:TABLe, 297
:SOURce:UNIT, 298
:STATus:OPERation:CONDition?, 299
:STATus:OPERation:ENABle, 299
:STATus:OPERation[:EVENt]?, 299
:STATus:OPERation:NTRansition, 300
:STATus:OPERation:PTRansition, 300
:STATus:PRESet, 301
:STATus:QUEStionable:ENABle, 301
:STATus:QUEStionable[:EVENt]?, 301
:SYSTem:BEEPer1[:IMMediate], 302
:SYSTem:BEEPer1:STATe, 302
:SYSTem:BEEPer2[:IMMediate], 302
:SYSTem:BEEPer2:STATe, 303
:SYSTem:DATE, 303
:SYSTem:ERRor:COUNt?, 304
:SYSTem:ERRor?, 304
:SYSTem:EXTRef?, 304
:SYSTem:KLOCk[:FPANel], 305
:SYSTem:KLOCk:KBD, 305
:SYSTem:KLOCk:MOUSe, 306
:SYSTem:POFF, 306
:SYSTem:PRESet, 306
:SYSTem:TIME, 307
:SYSTem:VERSion?, 307
:TRIGger[:SEQuence1]:DELay, 308
:TRIGger[:SEQuence1][:IMMediate], 308
:TRIGger[:SEQuence1]:SOURce, 310
:TRIGger:SEQuence2:DELay, 309
:TRIGger:SLOPe, 309
Lookup, 17
GPIB Commands Correspondence Table, 343
GPIB trigger, 67
H
Handler Interface
Setting the power supply, 151
Setting the pull-up resistors, 152
Handler interface
Electrical characteristics
Input signals, 149
Output signals, 147
Output, 144
pin layout, 142
Setting the pull-up resistors, 152
Timing chart, 146
Histogram, 119
How to use this manual, 17
I
Idle state, 66
Image, 169
Impedance measurement
Retrieving measurement results, 85
Initial Settings, 358
Initialize
Bin count, 111
Bin sort(Comparator) setup table, 106
Error queue, 204
Instrument, 206, 306
Measurement point(Stimulus) setup table, 27
Status register, 204, 301
Input signal drive voltage, 150
Interactive control, 164
Internal clock
Display on/off, 31
Set
Date, 303
Time, 307
Internal data arrays, 78
Internal data processing, 77
Internal trigger, 67
IP address
Factory setting, 364
How to set, 159
K
Key lock
Front panel, 305
Keyboard, 305
Mouse, 306
L
LAN, 157
Enable/Disable, 160
Setting an IP address, 159
LAN trigger, 67