User`s guide

Index-8
Index
phase or group delay
measurements
, 2-34
phaselinearityandgroupdelay
,
2-34
phase measurements
, 2-34
places where you can save
, 4-36
plot
aborting a process
, 4-33
plot files
outputting from a PC to a
plotter
, 4-24
outputting from a PC to an
HPGL compatible printer
,
4-25
sending to the printer
, 4-26
to output
, 4-14
to view on a PC
, 4-22
plot function, configuring
, 4-10
plotting to a pen plotter
, 4-12
plotting to an HPGL/2
compatible printer
, 4-10
plot function, defining
, 4-15
choosing display elements
, 4-15
choosing plot speed
, 4-18
choosing scale
, 4-17
resetting plotting parameters to
default values
, 4-18
selecting auto-feed
, 4-15
selecting line types
, 4-17
selecting pen numbers and
colors
, 4-16
plot speed, choosing
, 4-18
plotting
measurement results
, 4-3
measurement to a disk
, 4-13
measurements in page
quadrants
, 4-30
multiplemeasurementsonafull
page
, 4-29
multiple measurements per
page from a disk
, 4-28
multiple measurements per
page using a pen plotter
,
4-20
one measurements per page
using a pen plotter
, 4-19
parameters, resetting to default
values
, 4-18
plotting to an HPGL compatible
printer
, 4-21
solving problems
, 4-35
plotting a measurement to a disk
to output the plot files
, 4-14
polar format
, 7-27
polar format markers
, 1-32
port extensions
, 5-5
power coupling options
, 7-10
channel coupling
, 7-10
test port coupling
, 7-10
power levels, determining
, 1-60
power meter
calibration
, 2-12
calibration over IF range
, 2-20
calibration over RF range
, 2-23
power meter measurement
calibration
, 6-33
calibratingtheanalyzerreceiver
to measure absolute power
,
6-39
compensating for directional
coupler response
, 6-35
entering the power sensor
calibration data
, 6-34
interpolation in power meter
calibration
, 6-34
loss of power meter calibration
data
, 6-33
using continuous correction
mode
, 6-38
using sample-and-sweep
correction mode
, 6-36
power ranges
, 7-9
automatic mode
, 7-9
manual mode
, 7-9
power ranges, selecting
, 1-62
power sensor calibration data,
entering
, 6-34
power sweep
, 7-19
power, output
, 7-9
primary measurement channels,
viewing
, 1-12
principles, group delay
, 7-30
print
aborting a process
, 4-33
print function
configuring
, 4-4
defining
, 4-6
printer
color printer, using
, 4-6
HPGL compatible printer
, 4-21,
4-25
HPGL/2 compatible printer
,
4-10
printing
measurement results
, 4-3
multiple measurements per
page
, 4-9
one measurement per page
, 4-8
parameters, resetting to default
values
, 4-7
sequence
, 1-105
solving problems
, 4-35
printing or plotting the list values
or operating parameters
, 4-34
entire list of values
, 4-34
single page of values
, 4-34
procedure
high power measurements
, 1-60
procedure, TRL calibration
, 7-71
procedures for error correcting
measurements
, 6-10
types of error correction
, 6-10
processing details
, 7-6
accuracy enhancement
, 7-7
ADC
, 7-6
conversion
, 7-7
display memory
, 7-8
electrical delay block
, 7-7
format
, 7-8
format arrays
, 7-8
gating
, 7-7
IF detection
, 7-6
pre-raw data arrays
, 7-7
ratio calculations
, 7-6
raw arrays
, 7-7
sampler/IF correction
, 7-6
scale and offset
, 7-8
smoothing
, 7-8
sweep-to-sweep averaging
, 7-6
trace math operation
, 7-7
transform
, 7-8
vector error-correction
, 7-7
processing, data
, 7-5
prompting user to connect mixer
test setup
, 2-28
purging a sequence from a disk
,
1-104
R
R channel inputs, internal and
external
, 2-10
range
, 3-30
forward transform
, 3-24
resolution
, 3-34
ratio calculations
, 7-6
ratio measurements in channel 1
and 2, to
, 1-20
raw arrays
, 7-7
raw source match
, 7-70
real format
, 7-29
recall time, reducing
, 5-18
recalling a file
, 4-53
solving problems
, 4-54
recalling instrument states
, 4-36
receiver
calibration
, 6-15
crosstalk, reducing
, 5-15, 5-18
noise floor, reducing
, 5-15
receiver block
, 7-4
reducing
averaging factor
, 5-12