User`s guide

Index
Index-7
viewing, 1-20
memory, display
, 7-8
menu
address
, 7-79
analog in
, 7-22
calibration kit
, 7-57
conversion
, 7-22
edit limits
, 7-82
edit segment
, 7-82
input ports menu
, 7-23
offset limits
, 7-82
segment
, 7-16
S-parameter
, 7-22
stepped edit list
, 7-16
stepped edit subsweep
, 7-16
swept edit list
, 7-17
swept edit subsweep
, 7-17
microprocessor
, 7-4
microwave connector care
, 5-3
microwave systematic errors,
characterizing
, 7-41
minimizing
error when using adapters
, 6-48
source and load mismatches
, 2-4
minimum allowable stop
frequencies
, 3-16
minimum amplitude, searching
for
, 1-39
minimum bandwidth
, 1-94
minimum sweep time
, 7-11
mixer
fixed IF measurements
, 2-26
measurement
, 2-3
measurement diagram, using
,
2-15, 2-23
mixing signals, eliminating
unwanted
, 2-6
mode
auto sweep time
, 5-12, 7-11
chop sweep
, 5-13
continuous correction
, 6-38
copy
, 7-79
frequency offset
, 2-39
GPIO
, 7-80
low pass impulse
, 3-20
manual sweep time
, 7-11
network analyzer
, 7-83
pass control
, 7-78
system controller
, 7-78
talker/listener
, 7-78
time domain bandpass
, 3-12
time domain low pass
, 3-15
tuned receiver
, 7-83
model
one-port error
, 7-41
two-port error
, 7-46
modified colors
, 1-23
recalling
, 1-23
saving
, 1-23
modify colors menu
, 1-21
modifying
cal kit through definition
, 6-46
command
, 1-101
standard definitions
, 6-51
modifying calibration kits
, 7-56
calibration kit menu
, 7-57
saving to a disk
, 7-65
verifying performance
, 7-64
multiple
measurements per page,
plotting from a disk
, 4-28
measurements,plottingonafull
page
, 4-29
plots,outputtingtoasinglepage
using a plotter
, 4-27
N
N dB Point
, 1-94
names for CSV files
, 4-45
naming files generated by a
sequence
, 1-103
network analyzer mode
, 7-83
noise reduction techniques
, 7-34
averaging
, 7-34
IF bandwidth reduction
, 7-36
smoothing
, 7-34
non-coaxial
making measurments
, 6-49
non-coaxial devices, calibrating
for
, 6-51
noninsertable devices,calibrating
for
, 6-40
O
offset and scale
, 7-8
offset limits menu
, 7-82
offset, electrical
, 6-6
offsetting limit lines
, 1-80
omitting isolation calibration
, 6-4
one-portcalibration, S11 andS22
,
7-54
one-port error model
, 7-41
one-port reflection error
correction
, 6-26
operating parameters, printing or
plotting
, 4-34
operation, frequency offset
, 7-84
operation, GPIB
, 7-77
operation, limit line
, 7-81
operation, system
, 7-3
operation, trace math
, 7-7
output power
, 7-9
power coupling options
, 7-10
understanding power ranges,
7-9
outputting
measurement results
, 1-6
multiple plots to a single page
using a plotter
, 4-27
plot files
, 4-14
plot files from a PC to a plotter
,
4-24
single page plots using a
printer
, 4-26
outputting plot files from a PC to
an HPGL compatible printer
,
4-25
sending the exit HPGL mode
and form feed sequence to
the printer
, 4-26
sending the HPGL initialization
sequence to the printer
,
4-26
sending the plot file to the
printer
, 4-26
storingthe exitHPGL modeand
form feed sequence
, 4-26
storing the HPGL initialization
sequence
, 4-25
P
page quadrants, plotting
measurements in
, 4-30
parameters
lower stopband
, 1-70
measurement
, 1-4, 1-69, 6-4
passband
, 1-70
upper stopband
, 1-70
pass control mode
, 7-78
passband parameters
, 1-70
PC, to view files on
, 4-22
pennumbersandcolors,selecting
,
4-16
pen plotter
, 4-19, 4-20
plotting to
, 4-12
performance verification
, 5-5
performance, verifying
, 7-64
performing
2-port error corrections
, 6-42
TRL calibration
, 6-53
TRM calibration
, 6-56
peripheral equipment, required
,
7-4
per-raw data arrays
, 7-7
phase
linearity
, 2-34
measurements
, 2-34
tracking
, 2-38
phase distortion
, 1-43, 1-46
phase format
, 7-24