User`s guide

Index
Index-3
viewing, 1-14
measurement data
dividing by the memory trace
,
1-20
subtracting memory trace
,
1-20
viewing
, 1-20
memory math functions
, 1-19
memory trace
viewing
, 1-20
memory traces
, 1-19
primary measurement
dual channel mode with
decoupled channel power
,
1-14
dual channel mode with
decoupled stimulus
, 1-13
primary measurement
channels
, 1-12
viewing
, 1-12
ratio measurements in channel
1 and 2, to
, 1-20
display intensity
, 1-21
display markers
coupling
, 1-31
uncoupling
, 1-31
display markers, activating
, 1-25
display memory
, 1-19, 7-8
display reference value, setting
,
1-37
display ripple test limits
, 1-88
display ripple test values
, 1-89
displayed measurement, titling
,
4-32
displaying the bandwidth
markers
, 1-95
displaying the bandwidth value
,
1-96
drift, frequency
, 5-5
drift, temperature
, 5-5
dual channel mode with
decoupled power
, 1-14
dual channel mode with
decoupled stimulus
, 1-13
duplexer, characterizing
, 1-50
dynamic range, increasing
, 5-15
E
edit limits menu
, 7-82
edit segment menu
, 7-82
editing a sequence
, 1-100
deleting commands
, 1-100
editing line segments
, 1-79
editing ripple limits
, 1-85–1-87
electrical
length
, 1-43
offset
, 6-6
electrical delay
, 7-33
electrical delay block
, 7-7
electrical delay, setting
, 1-38
electrically long devices
, 5-4
eliminatingunwantedmixingand
leakage signals
, 2-6
embedding loop counter value in
title
, 1-106
enhanced frequency response
error correction
, 6-22
enhancement, accuracy
, 7-37
entering the power sensor
calibration data
, 6-34
deleting frequency signals
, 6-35
editing frequency segments
,
6-34
error
minimizing error while using
adapters
, 6-48
error correcting measurements
,
6-10
error correction
enhanced frequency response
,
6-22
frequency response
, 6-12
full two-port
, 6-29
one-port reflection
, 6-26
error-correction
, 1-5
stimulus state
, 6-9
error-correction, vector
, 7-7
errors, measurement
, 7-38
exit HPGL mode
, 4-26
sending to the printer
, 4-26
external
calibration
, 5-13
disk drive
, 4-54
R channel inputs
, 2-10
F
fabricating and defining
calibration standards for
TRL/LRM
, 7-73
fast 2-port calibration
, 5-13
fault location measurements
using low pass
, 3-17
features that operate differently
in sequence
, 1-105
feedthrough, RF
, 2-46
file
deleting
, 4-51
index numbers
, 4-45
recalling
, 4-53
renaming
, 4-52
sequential CSV naming of
, 4-45
to delete all
, 4-51
filter, characteristics
, 1-69
finiteimpulsewidth(orrisetime)
,
3-27
fixed IF mixer adjustments
tuned receiver mode
, 2-26
fixed IF mixer measurements
,
2-26
addressing and configuring two
sources
, 2-29
calling the next measurement
sequence
, 2-29
decrementing the loop counter
,
2-31
frequency list sweep of 26
points
, 2-28
incrementing the source
frequencies
, 2-31
initializingloop counter valueto
26
, 2-29
labeling the screen
, 2-31
presetting the instrument
, 2-27
promptingusertoconnectmixer
test setup
, 2-28
response calibration
, 2-28
sequence 1 setup
, 2-26
sequence 2 setup
, 2-31
taking data
, 2-31
tuned receiver mode
, 2-28
fixed markers
, 1-29
fixtures
, 6-49
designing your own fixture
, 6-50
flat limit lines
, 1-74
floppy disk, what you can save
,
4-37
form feed sequence
, 4-26
sending to the printer
, 4-26
format
, 7-8
format arrays
, 7-8
format markers, polar
, 1-32
formats, analyzer display
, 7-24
formatting a disk
, 4-53
forward stepping in edit mode
,
1-106
forward transform
measurements
, 3-22
demodulating the results of the
forward transform
, 3-23
forward transform range
, 3-24
interpreting the forward
transform horizontal axis
,
3-23
interpreting the forward
transform vertical axis
,
3-22
forward transform mode
, 3-4
forward transform range
, 3-24
four-channel display
4 Param Displays softkey
, 1-18