User`s guide

Index-2
Index
calling the next measurement
sequence
,2-29
capabilities
mixer measurement
,2-3
capacitance, fringe
,6-6
cause of measurement problems
,
5-8
center frequency, setting
,1-35
changing
sequence title
,1-103
system bandwidth
,5-16
changing the ripple limits color
,
1-89
channel coupling
,7-10
channel position softkey
,1-17
channel stimulus coupling
,7-14
characteristics of the filter
,1-69
characterizing a duplexer
,1-50
definitions
,1-50
procedure
,1-50
characterizing microwave
systematic errors
,7-41
device measurement
,7-46
one-port error model
,7-41
two-port error model
,7-46
choosing
display elements
,4-15
measurement parameters
,1-4
plot speed
,4-18
scale
,4-17
chopsweepmode,activating
,5-13
CITIfile
,4-41
clarifying type-N connector sex
,
6-4
clearingasequencefrommemory
,
1-102
color
changing the ripple limits
,1-89
ripple test message
,1-88
color printer, using
,4-6
colors of the display, adjusting
,
1-21
default
,1-21
intensity
,1-21
modified
,1-23
modify colors menu
,1-21
command
deleting
,1-100
inserting
,1-101
modifying
,1-101
commands that require clean
sweep
,1-106
commands that sequencing
completes before next
command
,1-105
comma-separated values. See
CSV format
compensating for directional
coupler response
,6-35
compliance with German noise
requirements
,8-7
computer,whatyoucansave
,4-37
configuring
plot function
,4-10
configuring two sources
,2-29
connecting
device under test
,1-4
required test equipment
,1-4
connector
care
,5-3
repeatability
,5-4
continuous correction mode,
using
,6-38
continuous markers
,1-24
conversion
,7-7
conversion compression using
frequency offset mode
,2-39
conversion loss
,2-20
conversion loss using frequency
offset mode
,2-13
conversion menu
,7-22
copy mode
,7-79
correction, sampler/IF
,7-6
coupling display markers
,1-31
coupling, channel stimulus
,7-14
creating
flat limit lines
,1-74
sequence
,1-98
sloping limit line
,1-76
user-defined TRL calibration
kit
,6-51
user-defined TRM calibration
kit
,6-54
creating single point limits
,1-78
crosstalk
,7-40
CSVformat,savingmeasurement
results in
,4-44
CW frequency, setting
,1-38
CW time measurements
,3-22
CW time sweep
,7-19
D
data formats, ASCII
,4-41
data processing
,7-5
processing details
,7-6
data trace
,1-19
saving to display memory
,1-19
decision making functions
,1-112
decoupled
channel power
,1-14
stimulus
,1-13
decreasing
frequency span
,5-11
sweep rate
,5-9
time delay
,5-9
decrementing the loop counter
,
2-31
default colors
,1-21
defining
plot function
,4-15
print function
,4-6
defining a print function
color printer, using
,4-6
resetting print parameters to
default value
,4-7
delay block, electrical
,7-7
delay, electrical
,7-33
delay, group
,1-47,2-34
deleting
commands
,1-100
frequency signals
,6-35
line segments
,1-79
deleting a file
,4-51
all files
,4-51
instrument state file
,4-51
delta markers
,1-28
demodulating the results of the
forward transform
,3-23
designing your own fixture
,6-50
detecting IF delay
,5-11
detection, IF
,7-6
deviation from linear phase
,1-46
device measurement
,7-46
device measurements
,6-4
device under test
measuring
,1-5
device under test, connecting
,1-4
direct sampler access
configurations, using
,5-17
directional coupler response,
compensating for
,6-35
discrete markers
,1-24
disk
formatting
,4-53
disk, plotting a measurement to
,
4-13
display elements, choosing
,4-15
display functions
,1-10
active channel display
,1-11
titling
,1-11
adjusting colors of the display
,
1-21
blanking the display
,1-21
data trace
saving to display memory
,
1-19
four-channel display
4 Param Displays softkey
,
1-18
ChannelPositionsoftkey
,1-17
customizing
,1-17