Agilent Technologies 87050A Option K24 User’s and Service Guide
Agilent Technologies 87050A Option K24 User’s and Service Guide Multiport Test Set Use this manual with the following documents: PNA Series Network Analyzer On-line Help System and Application Note 1408-12 8719D/20D/22D Network Analyzer User’s Guide, Part Number 08720-90288 8753D Network Analyzer User’s Guide, Part Number 08753-90257 8753E Network Analyzer User’s Guide, Part Number 08753-90367 8719D/20D/22D Network Analyzer Service Guide, Part Number: 08720-90292 8753D Network Analyzer Service Guide, Part N
Warranty Statement THE MATERIAL CONTAINED IN THIS DOCUMENT IS PROVIDED “AS IS,” AND IS SUBJECT TO BEING CHANGED, WITHOUT NOTICE, IN FUTURE EDITIONS. FURTHER, TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, AGILENT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED WITH REGARD TO THIS MANUAL AND ANY INFORMATION CONTAINED HEREIN, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Safety Notes The following safety notes are used throughout this document. Familiarize yourself with each of these notes and its meaning before performing any of the procedures in this document. WARNING Warning denotes a hazard. It calls attention to a procedure which, if not correctly performed or adhered to, could result in injury or loss of life. Do not proceed beyond a warning note until the indicated conditions are fully understood and met. CAUTION Caution denotes a hazard.
iv
Contents 87050A Option K24 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 87050A Option K24 Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Verifying the Shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 General Specifications . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Connector Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 Troubleshooting and Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 General Troubleshooting Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 Troubleshooting Power Supply Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
87050A Option K24 User’s and Service Guide 1
87050A Option K24 Description Description The Agilent 87050A Option K24 Multiport Mechanical Switching Test Set is designed for use with 50 Ω network analyzers such as the Agilent PNA E8362B, PNA-L N5230A, 8719D/E, 8720D/E, 8722D/E and 8753D/E. The Test Set provides the ability to make single connection, multiple measurements of multiport devices with up to 24 ports, such as distribution amplifiers, taps, switches and couplers.
87050A Option K24 Verifying the Shipment Verifying the Shipment After the test set has been unpacked, keep the original packaging materials so they can be used if you need to transport the instrument.Inspect the test set and all accessories for any signs of damage that may have occurred during shipment. If your test set or any accessories appear to be damaged or missing refer to "Contacting Agilent" on page 57.
87050A Option K24 General Specifications General Specifications Table 2 Agilent 87050A Option K24 Specifications Parameter Specification Frequency Range 50 MHz to 20 GHz Isolation 0.50 GHz to 1.3 GHz ≥ 85 dB 1.3 GHz to 3.0 GHz ≥ 100 dB 3.0 GHz to 6.0 GHz ≥ 95 dB Return Loss 0.50 GHz to 1.3 GHz ≥ 24 dB 1.3 GHz to 3.0 GHz ≥ 20 dB 3.0 GHz to 6.0 GHz ≥ 14 dB 6.0 GHz to 12.4 GHz ≥ 12 dB 12.4 GHz to 20 GHz ≥ 8 dB Insertion Loss 0.5 GHz to 6.0 GHz ≤ 2.5 dB 6.0 GHz to 12.4 GHz ≤ 3.
87050A Option K24 General Specifications Power Requirements NOTE Refer to your network analyzer documentation for specifications and power requirements. Verify that the required ac power is available at all necessary locations before installing the Test Set to the PNA. • Air conditioning equipment (or other motor–operated equipment) should not be placed on the same ac line that powers the Test Set and PNA. • The line power module on your test set is an autoranging input.
87050A Option K24 General Specifications Environmental Requirements Operating Environment Indoor use only Operating Temperature: 0 to 55 °C (32 °F to 104 °F) Storage Temperature: -40 °C to +70 °C (–40 °F to +158 °F) Altitude: 10,000 feet (3,000 meters) Enclosure Protection IP 2 0 Environmental Tests The 87050A Option K24 complies with all applicable safety and regulatory requirements for the intended location of use and have been evaluated to assure that they are consistent with Agilent quality and reliab
87050A Option K24 General Specifications Dimensions and Space Requirements Standard installation of the 87050A Option K24 and PNA includes configuration and installation on a customer provided lab bench or table top of adequate size and strength. Table 3 Instrument Dimensions Model Weight Height Width Depth E8362B 29 kg (64 lb) 26.7 cm (10.5 in) 42.5 cm (16.7 in) 42.6 cm (16.8 in) N5230A 24.9 kg (55 lb, ±0.5 lb) 26.7 cm (10.5 in) 42.5 cm (16.7 in) 42.6 cm (16.
87050A Option K24 General Specifications Ventilation Requirements ESD (electrostatic discharge) must be eliminated by use of static-safe work procedures and an anti-static bench mat.Refer to “Electrostatic Discharge Protection” on page 56. The 87050A Option K24 and the PNA are listed in “Environmental Requirements” are listed on Page 6. Note that these requirements are the same as those of the E8362B and N5230A PNA-L.
87050A Option K24 Front and Rear Panel Features Front and Rear Panel Features This chapter contains information on the ports and switches found on the front and rear panels of the test set. Figure 3 Front Panel Reflection 50 Ω Port Connection Line Power Switch Status LCD Transmission 50 Ω Test Ports 1–24 Ground Connector Line Power Switch The Test Set line power switch is located at the bottom left corner of the front panel. See Figure 3.
87050A Option K24 Figure 4 Front and Rear Panel Features Physical Characteristics of the 3.5 mm Connector Transmission and Reflection Ports The Transmission and Reflection Ports are female 3.5 mm 50 Ω connectors. A 50 Ω cable connects directly to the Port 1/Port 2 or Reflection/Transmission port of the network analyzer using the cable (08720-20245) that was shipped with your Test Set. CAUTION Refer to your analyzer documentation for damage limits to the RF OUT port.
87050A Option K24 Figure 5 Front and Rear Panel Features Rear Panel Parallel Port Input Printer/Test Set Switch Parallel Port Output Address Switch GPIB connector Line Module Parallel Port Input Connector This input is connected to the network analyzer. The analyzer provides control signals that drive the switches inside the test set. In pass-through mode, it also accepts signals required to drive a printer.
87050A Option K24 Front and Rear Panel Features Address Switch The address switch sets the GPIB or parallel address of the test set. See “Setting the Test Set Address Switch” on page 16 for information. Line Module The line fuse and a spare reside within the line module. Figure 6 illustrates where the fuses are and how to access them. Figure 6 Line Module Available Fuse • Fuse (F 3 A/250 V, part number 2110-0780) UL listed and CSA certified.
87050A Option K24 Power Cables Power Cables The line power cable is supplied in one of several configurations, depending on the destination of the original shipment. Each instrument is equipped with a three-wire power cable. When connected to an appropriate ac power receptacle, this cable grounds the instrument chassis. The type of power cable shipped with each instrument depends on the country of destination. See Figure 7 on page 14 for the part numbers of these power cables.
87050A Option K24 Figure 7 Power Cables Power Cable and Line (Mains) Plug Part Numbers a Plug Type 250V Cable Part Number Plug b Length Description cm (in.
87050A Option K24 System Setup System Setup The test set is designed to be placed underneath the network analyzer in a rack system and connected as shown in Figure 8. Use the two SMA 50 Ω jumper cables (08720-20245) included in the shipment. See Table 1 on page 3. Figure 8 Connecting the Test Set to the Network Analyzer After all the proper connections have been made, turn on the test set using the front panel line switch.
87050A Option K24 System Setup Setting the Test Set Address Switch The test set is shipped with the GPIB (HP-IB) address set to 12, which sets the parallel address to 0 as in Figure 9. Refer to “Operation” on page 18 for the definition of the parallel address. To set the GPIB address, set all five switches so that the sum of the switches in the On or “1” position equal the desired address. In the example below, the two switches in the “On” position are 8 and 4, therefore the GPIB address is 12.
87050A Option K24 System Setup Performance Verification For information on how to control the test set, refer to “Operation” on page 18. The following performance verification is designed to provide you with a high degree of confidence that your test set is working properly. It is not designed to verify specifications. To verify specifications, refer to “Performance Tests” on page 30. Equipment Required • Network Analyzer, 50 Ω impedance (Agilent 8720D) • Cable, 50 Ω 3.
87050A Option K24 Operation Operation The Agilent 87050A Option K24 is a “slave” instrument: a controller must be used to control the test set.
87050A Option K24 Operation Figure 10 Controlling the Test Set Over GPIB NOTE Connection to the network analyzer is not required when controlling the test set over GPIB. Network Analyzer Control The third method of sending commands uses the network analyzer to control the test set directly. This method is performed with the standard setup of the network analyzer working with the test set. A parallel cable is connected from the network analyzer output to the test set input on both rear panels.
87050A Option K24 Table 4 Operation Test Port Addresses Connection Path GPIB Command Decimal [D] Binary Equivalent Transmission to Port 1 tran_01 0 00000000 Transmission to Port 2 tran_02 1 00000001 Transmission to Port 3 tran_03 2 00000010 Transmission to Port 4 tran_04 3 00000011 Transmission to Port 5 tran_05 4 00000100 Transmission to Port 6 tran_06 5 00000101 Transmission to Port 7 tran_07 6 00000110 Transmission to Port 8 tran_08 7 00000111 Transmission to Port
87050A Option K24 Table 4 Operation Test Port Addresses Connection Path GPIB Command Decimal [D] Binary Equivalent Reflection to Port 5 refl_05 29 00011101 Reflection to Port 6 refl_06 30 00011110 Reflection to Port 7 refl_07 31 00011111 Reflection to Port 8 refl_08 32 00100000 Reflection to Port 9 refl_09 33 00100001 Reflection to Port 10 refl_10 34 00100010 Reflection to Port 11 refl_11 35 00100011 Reflection to Port 12 refl_12 36 00100100 Reflection to Port 13 ref
87050A Option K24 Operation To connect all ports to their internal 50 Ω loads, send the following two commands: OUTPUT 716;"PARAOUT24;" OUTPUT 716;"PARAOUT49;" or OUTPUT 712;"*t_term" OUTPUT 712;"*r_term" NOTE When a test set port is not in use, it is terminated in 50 Ω.
87050A Option K24 Table 5 Operation Switch Count Commands Switch Number GPIB Command J10 SW10? J11 SW11? J12 SW12? J13 SW13? J14 SW14? J15 SW15? J16 SW16? J17 SW17? J18 SW18? J19 SW19? J50 SW50? J51 SW51? J52 SW52? J53 SW53? J54 SW54? J55 SW55? J56 SW56? J57 SW57? J58 SW58? J59 SW59? J60 SW60? J61 SW61? J62 SW62? J63 SW63? J64 SW64? J65 SW65? J66 SW66? J67 SW67? J68 SW68? J69 SW69? User’s and Service Guide 23
87050A Option K24 Table 5 24 Operation Switch Count Commands J70 SW70? J71 SW71? J72 SW72? J73 SW73? User’s and Service Guide
87050A Option K24 Operation Calibrating the Test System After the test set has warmed up for at least two hours, you should calibrate before making any measurements. Refer to your network analyzer user’s guide to determine the type of calibration appropriate for the measurements you will be making. You must calibrate each measurement path separately and store the calibration as an instrument state in the network analyzer.
87050A Option K24 Operation Making Measurements The following examples assume that you are using a parallel port connection with an 8720D, with the test set's parallel address set to "0". See “Setting the Test Set Address Switch” on page 16 for information on setting the test set address. Measuring Reflection By leaving the DUT connected, as shown in Figure 12, and setting the network analyzer to measure S11, you can measure reflection or return loss.
87050A Option K24 Figure 12 Operation Controlling the Test Set User’s and Service Guide 27
87050A Option K24 Theory of Operation Theory of Operation The theory of operation begins with a general description of the 87050A Option K24 Multiport Test Set. This is followed by more detailed operating theory. The operation of each group is described briefly, to the assembly level only. Detailed component level circuit theory is not provided. System Theory The test set consists of three main components: a power supply, a front panel display and a controller interface mother board.
87050A Option K24 Theory of Operation Each path is routed to a bank of four 1 × 6 switches, for a total of eight 1 × 6 switches. Each bank of switches is routed to a single 1 × 4 switch where it becomes either the Transmission or Reflection port. All switches are mechanical, biased according to the necessary switching path. A user interface through the GPIB and parallel ports converts the necessary input signals from the user to the necessary control signals to control the switching paths.
87050A Option K24 Performance Tests Performance Tests Performance testing consists of measuring insertion loss, return loss and isolation between all ports. For the most accurate measurements, the use of an Agilent 8720D 50 Ω Network Analyzer is recommended and its use is recommended in this document. Familiarity with RF/microwave measurements is assumed. The use of adapters may be required and their effects should be accounted for.
87050A Option K24 Performance Tests Return Loss This test will verify the internal termination load of each port and the through match when the appropriate input port is terminated with a load. Step 1. Perform a one-port reflection calibration at the end of a 50 Ω cable over the frequency range of 50 MHz to 20 GHz on the analyzer. Verify the calibration is active and that the terminated cable displays a return loss of 0 (± 0.2 dB). Step 2.
87050A Option K24 Performance Tests Performance Test Record NOTE The following pages (Performance Test Record) are designed to be duplicated and used as a template for either of the Transmission or Reflection ports during each of the performance tests (Insertion Loss, Return Loss, and Isolation). At the top of each page, circle the appropriate input port (Transmission or Reflection), and write in the test date.
87050A Option K24 Table 6 Performance Tests Insertion Loss Test Record Transmission/Reflection Test Description Date______________ Port Minimum Specifications Measured Results Measured Uncertainty Port 1 ≤2.5 dB _______________ ±0.3 dB Insertion Loss to Band 1 Port 2 ≤2.5 dB _______________ ±0.3 dB 0.5 GHz to 6.0 GHz Port 3 ≤2.5 dB _______________ ±0.3 dB Port 4 ≤2.5 dB _______________ ±0.3 dB Port 5 ≤2.5 dB _______________ ±0.3 dB Port 6 ≤2.5 dB _______________ ±0.
87050A Option K24 Table 7 Performance Tests Insertion Loss Test Record Transmission/Reflection Test Description 34 Date______________ Port Minimum Specifications Measured Results Measured Uncertainty Port 1 ≤3.5 dB _______________ ±0.3 dB Insertion Loss to Band 2 Port 2 ≤3.5 dB _______________ ±0.3 dB 6.0 GHz to 12.4 GHz Port 3 ≤3.5 dB _______________ ±0.3 dB Port 4 ≤3.5 dB _______________ ±0.3 dB Port 5 ≤3.5 dB _______________ ±0.3 dB Port 6 ≤3.5 dB _______________ ±0.
87050A Option K24 Table 8 Performance Tests Insertion Loss Record Transmission/Reflection Test Description Date______________ Port Minimum Specifications Measured Results Measured Uncertainty Port 1 ≤4.5 dB _______________ ±0.3 dB Insertion Loss to Band 3 Port 2 ≤4.5 dB _______________ ±0.3 dB 12.4 GHz to 20 GHz Port 3 ≤4.5 dB _______________ ±0.3 dB Port 4 ≤4.5 dB _______________ ±0.3 dB Port 5 ≤4.5 dB _______________ ±0.3 dB Port 6 ≤4.5 dB _______________ ±0.
87050A Option K24 Table 9 Performance Tests Return Loss Test Record Transmission/Reflection Test Description 36 Date______________ Port Minimum Specifications Measured Results Measured Uncertainty Port 1 .≥24 dB _______________ ±1.5 dB Return Loss Band 1 Port 2 ≥24 dB _______________ ±1.5 dB 0.5 GHz to 1.3 GHz Port 3 ≥24 dB _______________ ±1.5 dB Port 4 ≥24 dB _______________ ±1.5 dB Port 5 ≥24 dB _______________ ±1.5 dB Port 6 ≥24 dB _______________ ±1.
87050A Option K24 Table 10 Performance Tests Return Loss Test Record Transmission/Reflection Test Description Date______________ Port Minimum Specifications Measured Results Measured Uncertainty Port 1 ≥20 dB _______________ ±1.5 dB Return Loss Band 2 Port 2 ≥20 dB _______________ ±1.5 dB 1.3 GHz to 3.0 GHz Port 3 ≥20 dB _______________ ±1.5 dB Port 4 ≥20 dB _______________ ±1.5 dB Port 5 ≥20 dB _______________ ±1.5 dB Port 6 ≥20 dB _______________ ±1.
87050A Option K24 Table 11 Performance Tests Return Loss Test Record Transmission/Reflection Test Description 38 Date______________ Port Minimum Specifications Measured Results Measured Uncertainty Port 1 ≥14 dB _______________ ±0.6 dB Return Loss Band 3 Port 2 ≥14 dB _______________ ±0.6 dB 3.0 GHz to 6.0 GHz Port 3 ≥14 dB _______________ ±0.6 dB Port 4 ≥14 dB _______________ ±0.6 dB Port 5 ≥14 dB _______________ ±0.6 dB Port 6 ≥14 dB _______________ ±0.
87050A Option K24 Table 12 Performance Tests Return Loss Test Record Transmission/Reflection Test Description Date______________ Port Minimum Specifications Measured Results Measured Uncertainty Port 1 ≥12 dB _______________ ±0.5 dB Return Loss Band 4 Port 2 ≥12 dB _______________ ±0.5 dB 6.0 GHz to 12.4 GHz Port 3 ≥12 dB _______________ ±0.5 dB Port 4 ≥12 dB _______________ ±0.5 dB Port 5 ≥12 dB _______________ ±0.5 dB Port 6 ≥12 dB _______________ ±0.
87050A Option K24 Table 13 Performance Tests Return Loss Record Transmission/Reflection Test Description 40 Date______________ Port Minimum Specifications Measured Results Measured Uncertainty Port 1 ≥8 dB _______________ ±0.5 dB Return Loss Band 5 Port 2 ≥8 dB _______________ ±0.5 dB 12.4 GHz to 20 GHz Port 3 ≥8 dB _______________ ±0.5 dB Port 4 ≥8 dB _______________ ±0.5 dB Port 5 ≥8 dB _______________ ±0.5 dB Port 6 ≥8 dB _______________ ±0.
87050A Option K24 Table 14 Performance Tests Isolation Test Record Transmission/Reflection Test Description Date______________ Port Minimum Specifications Measured Results Measured Uncertainty Port 1 ≥85 dB _______________ ±5 dB Isolation Band 1 Port 2 ≥85 dB _______________ ±5 dB 0.5 GHz to 1.
87050A Option K24 Table 15 Performance Tests Agilent 87050A Option K24 Isolation Test Record Transmission/Reflection Test Description 42 Date______________ Port Minimum Specifications Measured Results Measured Uncertainty Port 1 ≥100 dB _______________ ±5 dB Isolation Band 2 Port 2 ≥100 dB _______________ ±5 dB 1.3 GHz to 3.
87050A Option K24 Table 16 Performance Tests Isolation Test Record Transmission/Reflection Test Description Date______________ Port Minimum Specifications Measured Results Measured Uncertainty Port 1 ≥95 dB ___________ ±5 dB Isolation Band 3 Port 2 ≥95 dB ___________ ±5 dB 3.0 GHz to 6.
87050A Option K24 Table 17 Performance Tests Isolation Test Record Transmission/Reflection Test Description Date______________ Port Minimum Specifications Measured Results Measured Uncertainty Port 1 ≥90 dB _______________ ±7 dB Isolation Band 4 Port 2 ≥90 dB _______________ ±7 dB 6.0 GHz to 20.
87050A Option K24 Assembly Replacement and Post-Repair Procedures Assembly Replacement and Post-Repair Procedures The following table contains the list of replaceable parts for the Agilent 87050A Option K24 test set. If any of these parts or assemblies is replaced, you must run all performance tests to verify conformance to specifications. NOTE Special options are built to order, therefore long lead times may be encountered when ordering replacement parts. Refer to “Contacting Agilent” on page 57.
87050A Option K24 Table 18 Assembly Replacement and Post-Repair Procedures Agilent 87050A Option K24 Replaceable Parts Replacement Part Part Number Quantity RF Cable- Sw A15-1 87050-20084 1 RF Cable- Sw A19-1 87050-20085 1 RF Cable- Sw A20-1 87050-20086 1 RF Cable- Sw A21-1 87050-20087 1 RF Cable- Sw A1-2 87050-20088 1 RF Cable- Sw A2-2 87050-20089 1 RF Cable- Sw A3-2 87050-20090 1 RF Cable- Sw A7-2 87050-20091 1 RF Cable- Sw A8-2 87050-20092 1 RF Cable- Sw A9-2 87050-2009
87050A Option K24 Assembly Replacement and Post-Repair Procedures Connector Replacement The 50 Ω, 3.5 mm connectors are available separately as (5062-6618). It is possible to replace them in the field. An alternative to replacing a damaged connector would be to replace just the center pin components. The components for the assembly are: Component Part Number 3.5 mm Connector, RF (complete) 5062-6618 3.
87050A Option K24 Troubleshooting and Block Diagram Troubleshooting and Block Diagram This section contains information on troubleshooting the test set to the assembly level only. By following these procedures you should be able to determine whether the power supply, front panel, or main switch board needs replacing. Refer to Figure 13, “Agilent 87050A Option K24 Block Diagram,” as an aid in troubleshooting. Theory of operation information can be found Page 28 of this manual.
87050A Option K24 Troubleshooting and Block Diagram Troubleshooting the Front Panel Board Turn the instrument power on and confirm the following: Step 1. Verify the condition of each of the switching paths by issuing commands to switch each of the paths to either the transmission or reflection path. Ensure that the LCD indicates the appropriate path. Step 2. If the LCD indicates a wrong path, the problem can lie either with the front panel board or with the main switch board.
87050A Option K24 Figure 13 50 Troubleshooting and Block Diagram Agilent 87050A Option K24 Block Diagram User’s and Service Guide
87050A Option K24 Safety and Regulatory Information Safety and Regulatory Information Introduction Review this product and related documentation to familiarize yourself with safety markings and instructions before you operate the instrument. The documentation contains information and warnings that must be followed by the user to ensure safe operation and to maintain the product in a safe condition. Before Applying Power Verify that the premises electrical supply is within the range of the instrument.
87050A Option K24 Safety and Regulatory Information General Safety Considerations Cautions Cautions applicable to this instrument. CAUTION The Mains wiring and connectors shall be compatible with the connector used in the premise electrical system. Failure, to ensure adequate earth grounding by not using the correct components may cause product damage, and serious injury. CAUTION Always use the three prong AC power cord supplied with this product.
87050A Option K24 Safety and Regulatory Information Warnings Warnings applicable to this instrument. WARNING Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended. Discard used batteries according to manufacturer’s instructions. WARNING This is a Safety Class I product (provided with a protective earthing ground incorporated in the power cord). The mains plug shall be inserted only into a socket outlet provided with a protective earth contact.
87050A Option K24 Safety and Regulatory Information Regulatory Information This section contains information that is required by various government regulatory agencies. Instrument Markings The instruction documentation symbol. The product is marked with this symbol when it is necessary for the user to refer to the instructions in the documentation. This symbol indicates that the instrument requires alternating current (ac) input.
87050A Option K24 Safety and Regulatory Information Battery Collection Do not throw batteries away but collect as small chemical waste, or in accordance with your country’s requirements. You may return the battery to Agilent Technologies for disposal. Refer to “Contacting Agilent” on page 57 for assistance.
87050A Option K24 Electrostatic Discharge Protection Electrostatic Discharge Protection Protection against electrostatic discharge (ESD) is essential while removing assemblies from or connecting cables to the network analyzer. Static electricity can build up on your body and can easily damage sensitive internal circuit elements when discharged. Static discharges too small to be felt can cause permanent damage.
87050A Option K24 Agilent Support, Services, and Assistance Agilent Support, Services, and Assistance Service and Support Options The analyzer’s standard warranty is a one-year return to Agilent Technologies service warranty. NOTE There are many other repair and calibration options available from the Agilent Technologies support organization. These options cover a range of service agreements with varying response times.
87050A Option K24 58 Agilent Support, Services, and Assistance User’s and Service Guide
