Technical data

922 Agilent InfiniiVision 2000 X-Series Oscilloscopes Programmer's Guide
Index
ESR (Standard Event Status Register), 128, 769
event status conditions occurred, 143
Event Status Enable Register (ESE), 126, 770
Event Status Register (ESR), 128, 181, 769
example code, :ACQuire:COMPlete, 185
example code, :ACQuire:SEGMented, 191
example code, :ACQuire:TYPE, 196
example code, :AUToscale, 154
example code, :CHANnel<n>:LABel, 225
example code, :CHANnel<n>:PROBe, 227
example code, :CHANnel<n>:RANGe, 233
example code, :DIGitize, 160
example code, :DISPlay:DATA, 258
example code, :DISPlay:LABel, 259
example code, :DISPlay:ORDer, 715
example code, :MEASure:PERiod, 362
example code, :MEASure:TEDGe, 364
example code, :MTESt, 379
example code, :POD<n>:THReshold, 414
example code, :RUN/:STOP, 176
example code, :SYSTem:SETup, 574
example code, :TIMebase:DELay, 748
example code, :TIMebase:MODE, 579
example code, :TIMebase:RANGe, 581
example code, :TIMebase:REFerence, 582
example code, :TRIGger:MODE, 598
example code, :TRIGger:SLOPe, 605
example code, :TRIGger:SOURce, 606
example code, :VIEW and :BLANk, 182
example code, :WAVeform, 650
example code, :WAVeform:DATA
, 637
example code, :WAVeform:POINts, 641
example code, :WAVeform:PREamble, 645
example code, :WAVeform:SEGMented, 191
example code, *RST, 138
example programs, 5, 799
EXE (Execution Error) status bit, 126, 128
execution error detected in Standard Event
Status, 128
exponential notation, 117
external glitch trigger source, 615
external range, 274
external trigger, 271, 273, 606
EXTernal trigger commands, 271
EXTernal trigger level, 603
external trigger probe attenuation factor, 273
external trigger probe sensing, 717
EXTernal trigger source, 606
external trigger units, 275
F
failed waveforms in mask test, 388
failure, self test, 145
fall time measurement, 340, 350
Fast Fourier Transform (FFT) functions, 278,
281, 282, 284, 294, 718
FF values in waveform data, 637
FFT (Fast Fourier Transform) functions, 278,
281, 282, 284, 294, 718
FFT (Fast Fourier Transform) operation, 289,
649
FFT vertical units, 283
fifty ohm impedance, disable setting, 573
filename for hardcopy, 721
filename for recall, 419, 666
filename for save, 428
filter for frequency reject, 604
filter for high frequency reject, 593
filter for noise reject, 599
filter used to limit bandwidth, 220, 272
filters to Fast Fourier Transforms, 284
fine horizontal adjustment (vernier), 584
fine vertical adjustment (vernier), 236
finish pending device operations, 132
first point displayed, 659
FLATtop window for amplitude
measurements, 284
FM burst demo signal, 239
FM modulation type, waveform generator, 682
force trigger, 592
format, 639, 644
format for block data, 131
format for hardcopy, 720
format for image, 431
format for waveform data, 440
FormattedIO488 object, 53
formfeed for hardcopy, 296, 300
formulas for data conversion, 632
frame, 500
frame counters (CAN), error, 454
frame counters (CAN), overload, 455
frame counters (CAN), reset, 456
frame counters (CAN), total, 457
frame counters (UART), error, 515
frame counters (UART), reset, 516
frame counters (UART), Rx frames, 517
frame counters (UART), Tx frames, 518
framing, 498
frequency deviation, waveform generator FM
modulation, 674
frequency measurement, 51, 340, 351
frequency measurements with X cursors, 325
frequency resolution, 284
frequency span of display, 282
frequency versus dB, 278
front panel mode, 600
front panel Single key, 178
front panel Stop key, 180
front-panel lock, 568
FSK modulation type, waveform generator, 682
FSK rate, waveform generator modulation,
677
full-scale horizontal time, 581, 586
full-scale vertical axis defined, 290
function, 182, 280, 281, 282, 284, 288, 289,
290, 291, 292, 718, 719
FUNCtion commands, 277
function memory, 179
function turned on or off, 719
function, demo signal, 238
function, waveform generator, 667
functions, 649
G
g(t) source, first input channel, 286
g(t) source, math operation, 285
g(t) source, second input channel, 287
gateway IP, 42
general SBUS<n> commands, 449
general SEARch commands, 532
general trigger commands, 591
glitch demo signal, 238
glitch duration, 614
glitch qualifier, 613
glitch source, 615
GLITch trigger commands, 607
glitch trigger duration, 609
glitch trigger polarity, 612
glitch trigger source, 609
GPIB interface, 41, 42
graticule area for hardcopy print, 297
graticule colors, invert for hardcopy, 301, 723
graticule colors, invert for image, 432
grayscale palette for hardcopy, 309
grayscale palette for image, 433
grayscaling on hardcopy, 722
greater than qualifier, 613
greater than time, 609, 614
groups of digital channels, 411, 412, 414, 710
H
HANNing window for frequency
resolution, 284
hardcopy, 175, 296
HARDcopy commands, 295
hardcopy factors, 299, 430
hardcopy filename, 721
hardcopy format, 720
hardcopy formfeed, 300
hardcopy grayscale, 722
hardcopy invert graticule colors, 301, 723
hardcopy layout, 302
hardcopy palette, 309
hardcopy print, area, 297
hardcopy printer driver, 724
head type, probe, 228
header, 791
high resolution acquisition type, 631
high trigger level, 596
high-frequency reject filter, 593, 604
high-level voltage, waveform generator, 689
high-resolution acquisition type, 184
hold until operation complete, 132
holdoff time, 594
holes in waveform data, 637
hop frequency, waveform generator FSK
modulation, 676
horizontal adjustment, fine (vernier), 584
horizontal position, 585
horizontal scale, 583, 587
horizontal scaling, 644
horizontal time, 581,
586, 727
Host name softkey, 42