Agilent 16048E Test Leads Operation and Service Manual Fourth Edition Agilent Technologies Japan, Ltd.
Notices The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright.All rights are reserved. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of the Agilent Technologies. Agilent Technologies Japan, Ltd.
To avoid electric shock hazard, the instrument chassis and cabinet must be connected to a safety earth ground by the supplied power cable with earth blade. • DO NOT Operate In An Explosive Atmosphere Do not operate the instrument in the presence of flammable gasses or fumes. Operation of any electrical instrument in such an environment constitutes a definite safety hazard. • Keep Away From Live Circuits Operating personnel must not remove instrument covers.
Warranty This Agilent Technologies instrument product is warranted against defects in material and workmanship for a period corresponding to the individual warranty periods of its component products. Instruments are warranted for a period of one year. Fixtures and adapters are warranted for a period of 90 days. During the warranty period, Agilent Technologies Company will, at its option, either repair or replace products that prove to be defective.
Assistance Product maintenance agreements and other customer assistance agreements are available for Agilent Technologies products. For any assistance, contact your nearest Agilent Technologies Sales and Service Office. Addresses are provided at the back of this manual. Safety Symbol General definitions of safety symbols used on the instrument or in manuals are listed below.
Contents 1. Operation Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Compensation for Fixture Residual Impedance Error . . . . . . . . . . . . . . . . . . . . . Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setup and Measurement Procedure. . . . . . .
Contents 8
1 Operation This operating note provides complete information on the 16048E Test Leads. The 16048E is shown in Figure 1-1, its physical dimensions are given in Table 1-1. To order additional copies of this operating note, use the part number listed on the rear cover.
Operation Product Description Product Description The 16048E consists of a direct attachment, 4-terminal pair type fixture which is equipped with four BNC (m) terminated-coaxial test leads. These test leads are used to attach user-fabricated test fixtures. Cable length is 4 meter. The 16048E is shown in Figure 1-1.
Operation Specifications Specifications Table 1-1 Specifications of the 16048E Function: 4-terminal pair type fixture which is equipped with four BNC (m) terminated-coaxial test leads. Connector Type: BNC male Cable Length: Approximately 4 m Test Leads Length: Approximately 3.8 m Maximum Voltage: ± 40 V peak max.
Operation Compensation for Fixture Residual Impedance Error Compensation for Fixture Residual Impedance Error The 16048E has inherent stray capacitance, residual inductance, and residual resistance that affect the accuracy of measured values. To compensate for, or negate, these residuals to minimize measurement error, the instrument’s Open/Short compensation procedure should be performed. The procedure is given in the instrument’s operating manual.
Operation Operation Operation Setup and Measurement Procedure Setup and measurement procedure is as follows: 1. Connect the 16048E directly to the UNKNOWN terminals and GUARD terminal of the instrument. 2. Connect the user-fabricated test fixture to the test leads. 3. Perform Open/Short compensation as described in the instrument’s operation manual. 4. Connect the DUT to the 16048E test fixture.
Operation Operation 14 Chapter 1
2 Service 15
Service Maintenance Maintenance An exploded view of the 16048E (for parts identification) is shown in Figure 2-1 and Figure 2-2. Do not disassemble any further than shown. Maintenance consists principally of cleaning contacts and replacing worn or damaged parts. Take special care when cleaning contacts. To order parts, use the Agilent Technologies part numbers listed in Table 2-1 and Table 2-2.
Service Maintenance Table 2-1 Parts Identification 1/2 Reference 1 Agilent Part No. Qty. Description 16048-04013 1 COVER TOP 2360-0192 1 SCREW 2 16048-04014 1 COVER BOTTOM 3 1250-0089 4 CONTACT 4 1250-0052 4 CONNECTOR BNC 5 16047-40000 1 STOPPER 2190-0260 1 WASHER 2200-0013 1 SCREW 16048-61612 1 CABLE ASSEMBLY 0400-0203 1 GROMET 16048-04015 1 COVER TOP 2360-0192 2 SCREW 16048-60002a 1 TEST LEAD (1 through 7) 6 7 8 a. Agilent internal-only part number.
Service Maintenance Reference 12 13 18 Agilent Part No. Qty.
REGIONAL SALES AND SUPPORT OFFICES For more information about Agilent Technologies test and measurement products, applications, services, and for a current sales office listing, visit our web site: http://www.agilent.com/find/tmdir. You can also contact one of the following centers and ask for a test and measurement sales representative. 11/29/99 United States: Agilent Technologies Test and Measurement Call Center P.O.
