Agilent 11899A Probe Power Supply Operating and Service Note For use with the Agilent Technologies 83400 series lightwave sources and receivers
© Copyright Agilent Technologies 2000 All Rights Reserved. Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under copyright laws. Agilent Part No. 11899-90004 Printed in USA April 2000 Agilent Technologies Lightwave Division 1400 Fountaingrove Parkway Santa Rosa, CA 95403-1799, USA (707) 577-1400 Notice. The information contained in this document is subject to change without notice.
General Safety Considerations General Safety Considerations This product has been designed and tested in accordance with IEC Publication 61010-1, Safety Requirements for Electrical Equipment for Measurement, Control and Laboratory Use, and has been supplied in a safe condition. The instruction documentation contains information and warnings that must be followed by the user to ensure safe operation and to maintain the product in a safe condition.
General Safety Considerations WARNING This is a Safety Class 1 product (provided with a protective earthing ground incorporated in the power cord). The mains plug shall only be inserted in a socket outlet provided with a protective earth contact. Any interruption of the protective conductor inside or outside of the product is likely to make the product dangerous. Intentional interruption is prohibited. WARNING No operator serviceable parts inside. Refer servicing to qualified personnel.
General Safety Considerations CAUTION This instrument has autoranging line voltage input. Be sure the supply voltage is within the specified range.
Contents Contents The Agilent 11899A Probe Power Supply— At a Glance Performance Characteristics 9 Power Cords 10 Returning the Instrument for Service 12 Agilent Technologies Service Offices 15 6 7
The Agilent 11899A Probe Power Supply— At a Glance The Agilent 11899A Probe Power Supply— At a Glance The Agilent 11899A probe power supply provides regulated DC power at the front panel receptacles for operation of one or two probes.
The Agilent 11899A Probe Power Supply— At a Glance An extender cord (Agilent 10131B) can also be ordered to increase the length between the power supply and the probe. This manual provides operating and service information for the probe power supply. Perform all work at a static-safe workstation. Failure to protect against electrostatic discharge could result in damage to the instrument.
Performance Characteristics Performance Characteristics The following table contains performance characteristics for the Agilent 11899A probe power supply. These are not specifications, but are provided as information useful in operating the power supply. Probe Driving Capability 1 or 2 probes Power Output –12.
Power Cords Power Cords Plug Type Cable Part No. Plug Description Length (in/cm) Color Country 250V 8120-1351 Straight *BS1363A 90/228 Gray 8120-1703 90° 90/228 Mint Gray United Kingdom, Cyprus, Nigeria, Zimbabwe, Singapore 8120-1369 Straight *NZSS198/ASC 79/200 Gray 87/221 Mint Gray 250V 90° 8120-0696 250V 125V 250V Australia, New Zealand 8120-1689 Straight *CEE7-Y11 79/200 Mint Gray East and West Europe, Saudi Arabia, So.
Power Cords Plug Type Cable Part No. Plug Description Length (in/cm) Color Country 220V 8120-2956 Straight *DHCK107 79/200 Mint Gray Denmark 8120-2957 90° 79/200 Mint Gray 8120-4211 Straight SABS164 79/200 Jade Gray 8120-4600 90° 79/200 250V Republic of South Africa India 100V 8120-4753 Straight MITI 90/230 8120-4754 90° 90/230 Dark Gray Japan * Part number shown for plug is the industry identifier for the plug only.
Returning the Instrument for Service Returning the Instrument for Service The instructions in this section show you how to properly return the instrument for repair or calibration. Always call the Agilent Technologies Instrument Support Center first to initiate service before returning your instrument to a service office. This ensures that the repair (or calibration) can be properly tracked and that your instrument will be returned to you as quickly as possible.
Returning the Instrument for Service information should be returned with the instrument. • Type of service required. • Date instrument was returned for repair. • Description of the problem: • Whether problem is constant or intermittent. • Whether instrument is temperature-sensitive. • Whether instrument is vibration-sensitive. • Instrument settings required to reproduce the problem. • Performance data. • Company name and return address. • Name and phone number of technical contact person.
Returning the Instrument for Service Sealed Air Corporation (Commerce, California 90001). Air Cap looks like a plastic sheet filled with air bubbles. Use the pink (antistatic) Air Cap™ to reduce static electricity. Wrapping the instrument several times in this material will protect the instrument and prevent it from moving in the carton. 4 Seal the carton with strong nylon adhesive tape. 5 Mark the carton “FRAGILE, HANDLE WITH CARE”. 6 Retain copies of all shipping papers.
Agilent Technologies Service Offices Agilent Technologies Service Offices Before returning an instrument for service, call the Agilent Technologies Instrument Support Center at (800) 403-0801, visit the Test and Measurement Web Sites by Country page at http://www.tm.agilent.com/tmo/country/English/ index.html, or call one of the numbers listed below. Agilent Technologies Service Numbers Austria 01/25125-7171 Belgium 32-2-778.37.
