User's Manual Part 1
Table Of Contents
- Contents of the packages
- Remove the packing materials
- Remove Drystar5300 from pallet
- Unpack the accessories
- Environment specifications
- Remove transport protections (1 of 2)
- Remove transport protections (2 of 2)
- Adjust Input block module - 11x14” (1 of 2)
- Adjust Input block module - 11x14” (2 of 2)
- Connect the cables
- Load film in the input tray (1 of 2)
- Load film in the input tray (2 of 2)
- Startup Drystar5300
- Configure network settings
9/16
2923B EN 20031206
7 Remove transport protections (2 of 2)
7 Close top cover.
9 Remove foam block from input tray.
11 Take crosshead screwdriver.
1
3
2
4
5
6
XXXX
X
X
X
XXX XX
X
XX
X
XX
X
X
XX XXXX
X
X
XX
X
X
XXXXXX
XX
X
X XXXX
X
X
XXXXXX
XX
X
X
XXXXXX
XXXXX
X
XXXX XXX
X
X
X
XXXXXX
X
XXX XXXX
X
X
XXXXXX
X
X
XX
X
XXXXX
XXXX
X
X
X
XXX XX
X
XX
X
XXXXXX
X
XXX XXXX
X
X
XX
X
XX
X
XXXX XXX
X
X
X
XXXXXX
XX
X
X
XXXXXX
8 Open input tray.
10 Close input tray.
12 Remove drum screw.
1
3
2
4
5
6
X
XXX
X
X
X
XX
X
XX
XX
XX
X
X
XX
X
X
XXXX
X
X
XXX
X
X
X
X
XXX
X
X
X
X
X
XXX
XX
X
X
XXX
X
X
XXX
XX
XXX
X
XXX
X
XX
XX
X
X
X
X
XXX
X
X
X
XXX
X
XX
X
X
X
XXX
XX
XXX
XX
X
XXX
X
X
X
X
XXX
X
XX
X
XX
X
XX
X
XX
XXX
X
XX
XXX
X
XX
XX
X
XXX
X
X
X
XXX
XX
X
XXX
X
X
XXX
X
XXX
XX
X
X
X
X
X
X
X
X
XXX
1
3
2
4
5
6
X
X
X
XXX
X
X
XX
X
XXXX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XXX
X
X
X
XXX
XX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XX
XXXXXX
X
X
X
XX
X
XX
X
X
X
XX
X
X
X
XX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XX
X
XX
X
X
XX
X
X
XX
X
X
XX
X
X
X
X
XX
X
X
X
X
XX
X
X
XXX
X
X
X
X
X
X
X
XXX
XX
X
X
X
XX
X
X
X
XX
X
XX
X
X
X
X
B
Installation










