PLEASE RETAIN Ellesmere EC5 5.
TABLE OF CONTENTS PAGE NO. 1. AGA Solid Fuel Stove Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2. Installation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3. Important Operation/ Maintenance Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4. Installation & Operating Instructions . . . . . . . . .
AGA SOLID FUEL STOVE WARRANTY CONDITIONS OF WARRANTY Your AGA Solid Fuel Stove is guaranteed against any part that fails (under normal operating conditions) as detailed in the following table with timelines specified from the date of installation of the appliance. If the unit is not installed with- in six months of date of purchase, the warranty will commence six months from the date of purchase.
INSTALLATION CHECK LIST Tick Flue System 1. Minimum Flue Height of 4.6 metres (15 feet). 2. Appliance should be connected to a 125mm (5”) diameter flue pipe throughout 3. The horizontal flue run should not exceed 150mm (6”) 4. All flue pipework passing through walls must be sleeved & adequately insulated in line with current Building Regulations. 5.
IMPORTANT OPERATION / MAINTENANCE NOTES Now that your AGA Solid Fuel Stove is installed and no doubt you are looking forward to the many comforts it will provide, we would like to give you some tips on how to get the best results from your stove. 1. We would like if you could take some time to read the operating instructions/hints, which we are confident, will be of great benefit to you. 2. Do not burn fuel with a high moisture content, such as a damp peat or unseasoned timber.
INSTALLATION & OPERATING INSTRUCTIONS Please refer to the current standards, BS EN 152871:2007 Design, Installation and Commissioning of chimneys. BS EN 14336:2004: Heating Systems in Buildings. Installation & Commissioning of Water Based Heating Systems. BS EN 12828: 2003; Heating Systems in Buildings. Design of Water Based Heating Systems. BS EN 12831: 2003; Heating Systems in Buildings. method for calculation of the design heat load.
All register plates, restrictor plates, damper etc., which could obstruct the flue at a future date should be removed before connecting this appliance. The stove comes partially configured for top outlet and requires the flue spigot (supplied in the firebox) to be fitted to the top outlet flue connection as shown in Fig 3 using the nuts & bolts provided.
VENTILATION & COMBUSTION AIR REQUIREMENTS Fig.4 It is imperative that there is sufficient air supply to the stove in order to support correct combustion. The air supply to this appliance must comply with current Building Regulations Part J, Heat Providing Appliances. If another appliance is fitted in an adjacent room it will be necessary to calculate an additional air supply. Back Outlet The minimum effective air requirement for this appliance is 8.25cm².
If there is an extraction fan fitted in adjacent rooms where this appliance is fitted, additional air vents may be required to alleviate the possibility of spillage of products of combustion from the appliance/flue while the fan is in operation. Refer to B.S. 8303 Part 1. EXTERNAL DUCTED AIR Where such an installation exists, a test for spillage should be made with the fan or fans and other appliances using air in operation at full rate, (i.e.
HEAT RECOVERY VENTILATION Fig.7 Where a stove is to be installed in a dwelling with Heat Recovery Ventilation (HRV) a number of precautionary measures must be undertaken: Vertical Heat Shield Where the product is to be installed with a Mechanical Ventilation, the stove must be connected to an external air supply, The ductwork for the external air supply must be no longer than 6 metres and the air inlet terminal to the ductwork must have a cross sectional area of at least 80cm2.
STOVE DIMENSIONS Fig.9 COMMISSIONING AND HANDOVER On completion of the installation allow a suitable period of time for any fire cement and mortar to dry out, when a small fire may be lit and checked to ensure the smoke and fumes are taken from the stove up the chimney and emitted safely to the atmosphere. Do not run at full output for at least 24 hours. OPERATION Check that all dampers and catches are operating correctly and ensure that all flue connections are thoroughly sealed.
This stove has obtained HETAS Ltd approval for burning natural and manufactured smokeless fuels only as detailed in recommended fuels below. HETAS Approval does not cover the use of other fuels either alone or mixed with the recommended fuels listed, nor does it cover instructions for the use of other fuels. RECOMMENDED FUELS All fuels should be stored under cover and kept as dry as possible prior to use.
LIGHTING THE STOVE SLOW BURNING NOTE: When operating the stove, it is recommended to use the Glove provided to open the fire door as the door handle will become hot. 1. Open the fire door and open the primary air control by pulling it fully out. Open the secondary air inlet by pulling the control fully out. Cover the grate with crumpled pieces of paper and lay 10-12 pieces of kindling on top of the paper towards the back of the firebox. lgnite and close the fire door.
PERIODIC MAINTENANCE Adjusting the Door Catch MONTHLY MAINTENANCE Cleaning Stove Flue Pathways It is recommended that the flue pathways in the stove are cleaned on a monthly basis (or less depending on the soot build-up created by the fuel being used) and the chimney cleaned annually. To access the chimney pathways, use the following procedure: 1. Lift up the front of the bottom baffle to allow the two side bricks to drop into the firebox & be removed (see Fig 12). 2.
GLASS REPLACEMENT a. b. c. d. e. f. g. Open the door fully. Remove the four fixing screws and clips (see Fig 14). Clean the glass recess in the door. Replace the adhesive thermal tape on the back face of the door if damaged. Fit the glass in position and replace the four corner clips & screws. Hand tighten the screws, turning back 1/4” turn when hand tight. Replace glass only with ceramic glass. Fig.14 FIRE SAFETY To provide reasonable fire safety, the following should be given serious consideration.
EXPLODED VIEW 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 12. 13. 14. 15. 16. 17. 18. 19. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32.
This Stove has passed the Efficiency Category A+ Official Efficiency Rating: Manufactured Smokeless Fuel is 81.5 % Wood is 84.
