Installation Operation and Maintenance Instructions Hazardous Location Models 4EAF Freezer 6EAR Refrigerator 6ERF Combination Refrigerator / Freezer
CONTENTS Unpacking your refrigerator ................................................. Removing the packaging ..................................................... Warranty registration ......................................................... Installing your refrigerator ................................................... Select location .................................................................... Installation ..........................................................................
UNPACKING YOUR REFRIGERATOR Remove Packaging Your refrigerator has been packed for shipment with all parts that could be damaged by movement securely fastened. Cut the banding material at the bottom of the carton, unfold the carton at the bottom and remove the carton from the appliance. Remove the plastic bag, styrofoam corner posts, and any tape holding the door closed and internal components in place.
INSTALLING YOUR REFRIGERATOR These refrigerators and freezers have been engineered for institutional and industrial hazardous locations and meet Underwriters Laboratories specifications for Class 1 Groups C and D. Approved by the New York City Board of Standards and Appeals under Calendar Number 496-80-SA.
HANDLE INSTALLATION Step 1: Verify door alignment The door should be parallel to the sides and top of the refrigerator. If alignment is necessary the door may be adjusted by loosening the 2 screws which secure the hinge adapter brackets on the top and bottom of the door and adjusting the door side to side. Use a 5/32” allen wrench for this procedure. (See Figure 3 below). When finished aligning the door, tighten the screws securely. Handle Installation 1.
DIMENSIONS FOR 4EAF, 6EAR, 6ERF WITH SOLID DOOR 47-3/32” (119.61cm) 24-7/8” (63.20cm) 25-11/32” (64.36cm) 24-3/32” (64.19cm) 23-7/8” (60.7CM) 1” (2.54cm) 33-3/4” to 34-3/4” (85.7 to 88.3cm) 3” to 4” (7.6 to 10.2cm) 22” (55.9cm) ROUGH IN OPENING FOR 4EAF, 6EAR, 6ERF WITH SOLID DOOR 35-3/4” (90.2 cm) *24” (61 cm) standard cabinet depth * Depth dimension may vary depending on each individual installation. A minimum depth of 27-1/2” (69.9cm) is required with ample provision for wiring. 25-7/8” (65.
ADJUSTING THE TEMPERATURE CONTROL Energy Saving Tips The following suggestions will minimize the cost of operating your refrigeration appliance. Adjusting the temperature control The temperature control shaft is located behind the front grill on the right side of the cabinet. (See Figure 1, on page 4). It can be adjusted with a flat bladed screwdriver. 1. Do not install your appliance next to a hot appliance, (cooker, dishwasher, etc.). heating air duct, or other heat sources. 2.
CARE AND CLEANING Cleaning instructions Condenser The condenser tubing or fins behind the cabinet do not require frequent cleaning; however, satisfactory cooling depends on adequate ventilation over the condenser. Be sure that nothing obstructs the air flow openings in the front grill (see Figure 1). At least once or twice a year brush or vacuum the condenser for efficient performance. Use care when cleaning the condenser. The condenser fins are sharp and could cause cuts.
TROUBLESHOOTING YOUR REFRIGERATOR Before You Call for Service If the unit appears to be malfunctioning, read through this manual first. If the problem persists, check the troubleshooting guide below. Locate the problem in the guide and refer to the cause and its remedy before calling for service. The problem may be something very simple that can be solved without a service call. However, it may be required to contact your dealer or a qualified service technician.
OBTAINING SERVICE If Service is Required: • If the product is within the first year warranty period please contact your dealer or call AGA MARVEL Customer Service at 800.223.3900 for directions on how to obtain warranty coverage in your area. • If the product is outside the first year warranty period, AGA MARVEL Customer Service can provide recommendations of service centers in your area. A listing of authorized service centers is also available at www.agamarvel.com under the service and support section.
COMMERCIAL PRODUCT WARRANTY Entire Product - One Year Parts and Labor Warranty AGA MARVEL warrants to the original purchaser that it will supply all necessary parts and labor to repair or replace in the end user’s establishment, any component which is found by an authorized representative of AGA MARVEL to be defective in materials or workmanship, subject to the conditions and exclusions stated below, for a period of one year from the date of purchase by the end user.
www.agamarvel.com 1260 E. VanDeinse St. Greenville MI 48838 800.223.3900 41004297 Rev G 6/7/12 All specifications and product designs subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products.
