Analog Resistive Touchscreen ATP/AST Series Product Specifications
ATP/AST Series Product Specifications Table of Contents 1. Product Specifications ...........................................................................................................................3 1-1. Product Applicable .............................................................................................................................3 1-2. Structure...........................................................................................................................................
ATP/AST Series Product Specifications 1. Product Specifications 1-1. Product Applicable § This specification is applied to the analog resistive touchscreen: ATP/AST Series. 1-2. Structure § Dimensions, structure, and shape are referred on the drawing attached. 1-3. Environmental Specifications Specification Value Operating Temperature -20°C to 70°C (no condensation) Operating Humidity -20°C to 60°C Less than 90%RH (no condensation) 3 Exceeding 60°C 133.
ATP/AST Series Product Specifications 1-6. Appearance § Scratch, dust (W = width, L = length, D = average diameter = (longest + shortest) /2) Item Scratch Dust (Linear) Width (mm) Length (mm) Acceptable Numbers 0.1≥W>0.05 4≥L 1pcs in φ30mm 0.05≥W>0.03 10≥L 2pcs in φ20mm 0.03≥W 20≥L Acceptable 0.1≥W>0.05 5≥L 2pcs in φ30mm 0.05≥W Acceptable Acceptable Dust (Circular) Total Within 5pcs per product. 0.4≥D>0.3 *1 1pcs in Viewing Area *1 0.3≥D>0.2 2pcs in φ30mm 0.
ATP/AST Series Product Specifications 2. Testing Regulation 2-1. Testing Regulation § If the regulation is not specified, the test is performed under the supplier’s regulation. § Tests are performed under the room temperature unless specified. The room temperature is referred as follows: Temperature: 20°C±5°C Humidity: 65%±10%RH 2-2. Environmental Specifications § Chemical Resistance Test Condition: Tested after leaving the chemical on the surface for 12 hours being wiped off by cloth.
ATP/AST Series Product Specifications 2-4. Electrical Characteristics § Terminal Resistance Test Condition: Top and bottom electrodes are measured at the terminal. Judgement: Must satisfy the specification. § Insulation Resistance Test Neighboring Terminals: Measured by applying the reference voltage to the terminals Active Area Electrodes: Measured by applying the reference voltage to the top and bottom electrodes. Judgement: Must satisfy the specification. 2-5.
ATP/AST Series Product Specifications 3. Reliability Condition 3-1. Temperature Condition § Temperature Condition Test Following test are performed in the condition with no dew condensation: Cold Test: Tested after leaving the parts in -30°C±3°C for 240 hours and in the room temperature for 2 hours. Heat Test: Tested after leaving the parts in 80°C±3°C for 240 hours and in the room temperature for 2 hours.
ATP/AST Series Product Specifications 5. Handling Notes 5-1. Precautions § This product is intended for use in standard applications (computers, office automation, and other office equipment, industrial, communications, and measurement equipment, personal and household devices, etc.
ATP/AST Series Product Specifications 5-5. Mounting Notes Bezel § Bezel Edge Bezel edge must be positioned in the area between the Active Area and the Viewing Area. The bezel may press the touchscreen and cause input if the edge enters the Active Area. Bezel Top Electrode A gap of approximately 0.5mm is needed between the bezel and the top electrode. It may cause unexpected input if the gap is too narrow. 0.
ATP/AST Series Product Specifications 6. Warranty 6-1. Warranty Period § The warranty period is limited to 1 year from the date of shipping. The warranty for the initial defection such as appearance defection is limited to 1 month. § Any defected parts under proper use will be examined by the supplier and replaced by the new parts if the defection is considered to be caused by the supplier. § The replacement is subject to be included in the next lot. 6-2.
ATP/AST Series Product Specifications 7. Revision history Rev1 (April 15, 1998) Initial release Rev2 (June 1, 1999) The overall revision by specification review. Rev3 (April 1, 2002) The address in the office was changed by the move. Rev4 (August 16, 2002) 1-4.Activation Force is changed “50g± 30g” to “0.5N±0.3”. 1-4.Light Transmission is changed 76% to 80%(TYP). Rev5 (September 3, 2002) 1-3.Operating Temperature is changed “0°C to 60°C” to “-20°C to 70°C”. 1-3.
ATP/AST Series Product Specifications Rev10 (November 10, 2006) The specification item name was changed. 1-3.”Storing Temperature” to “Storage Temperature” 1-3.”Storing Humidity” to “Storage Humidity” 1-4.”Operating Load” to “Activation Force” 1-4.”Light Transmissivity” to “Light Transmittance” 1-4.”Top Surface Hardness” to “Surface Hardness” 2-3.”Operating Load Test” to “Activation Force Test” 2-3.”Operating Load” to “Activation Force” 3-1.”Operationg Load” to “Activation Force” 1-4.
ATP/AST Series Product Specifications ATP/AST Series Product Specifications Rev. 10, November 10, 2006 ©1999 - 2006 DMC Co., Ltd. This document can be freely distributed, but any alternation to this document is prohibited. http://www.dmccoltd.com/english/ 9th floor, Kanda Sento Building, 1-2-4 Yushima, Bunkyo-Ku, Tokyo 113-0034, Japan Phone: +81-3-5209-7131 (Japanese), 7135 (English) Fax: +81-3-5209-7130 13 Rev. 10©1999 - 2006 DMC Co., Ltd.
