Installation Guide

LED Indoor Luminaires
Undercabinet
120VAC, 50/60Hz
Page 2 of 2 8061394 R0
Part #: VRAU09**, VRAU14**
Part #: VRAU22**, VRAU32**
Part #: VRAU40**
Limited Factory Warranty
This product is manufactured by AFX Inc. AFX Inc. hereby warrants that this fixture is free from defects in materials and workmanship when installed
and used under normal operating conditions for a period of 7 years from date of purchase. This warranty covers all component parts and extends only to
replacement of defective fixture or components; it does not cover failure due to improper installation, misuse, mishandling or damage incurred in transit.
For questions, please call AFX 1-800-873-2326.
Step 4 – Link to fixture installation
A. First fixture in series can be corded (step 2) or hardwired (step 3).
B. If using butt connector (9), additional fixtures must have a 1” gap between
them. See below for number of fixtures that can be linked together.
Model
VRAU09**
VRAU14**
VRAU22**
VRAU32**
VRAU40**
Adjacent Linking Qty.
40
25
16
11
9
C. If using a linking cord, fixture must be located within desired length of linking
cord being used: 12”, 24”, 36”, 48” or 72” for linking cords (sold separately).
D. Make sure power is off on all fixtures.
E. Connect the linking cord or butt connector (9) to the “OUTPUT” connector of
the first fixture and into the “INPUT” connector of the second fixture
F. Follow the directions for mounting show in Step 6.
G. Once mounting is completed, energize the first fixture (Each fixture is controlled
individually).
Wiring – All wiring must take place inside junction box (not included)
Caution: Make sure power is off at fuse or circuit breaker box. Check power
wires for damage or scrapes. If power supply wires are within three inches of the LED
driver, use wire suitable for at least 90°C (194°F). Note: Most dwellings built before 1985
have supply wire rated to 60°C. Consult a qualified electrician to ensure correct branch
circuit conductor before installing.
Step 5 – Wiring
A. Pull the green, black, and white wires out of the fixture to allow connection to the branch
circuit.
B. Connect the green ground input supply wire to the fixture green ground wire. Do this by
inserting it into the open hole in the push-in wire connector (included) that is attached to the
green ground wire in the fixture.
C. For non-dimming fixture. Connect the white wire from the fixture to the white (N) wire
from supply power source. Do this by inserting it into the open hole of the push-in wire
connector that is attached to the white wire in the fixture. Connect the black fixture wire to
the black (L) wire from supply power source. Do this by inserting it into the open hole of the
push-in wire connector that is attached to the black wire in the fixture.
D. For TRIAC dimming. Connect the white wire from the fixture to the white (N) wire from
dimming source per dimmer wiring instructions. Do this by inserting it into the open hole of
the push-in wire connector that is attached to the white wire in the fixture Connect the black
wire from the fixture to the black (L) wire from dimmer supply power source per dimmer
wiring instructions. Do this by inserting it into the open hole of the push-in wire connector
that is attached to the black wire in the fixture.
E. Do not mix wires. Pull on each wire lead to make sure connections are secure. Make
certain no bare wires are exposed outside of wire connectors. Tuck all connections
neatly into the junction box.
Step 6 – Mounting
A. Use captivated screw hole locations (6) for mounting the fixture, position the fixture in
location intended for mounting. Mark the hole locations by using the screw-holes as a
guide. Drill suitable pilot holes in the marked positions. Mount the housing to desired
surface with the two captivated screws.
Step 7 – Restore power at fuse or circuit breaker box