Installation Sheet

ManualsBrandsAFX ManualsCabinet LightsLed T5L 42 in. LED Oil-Rubbed Bronze Under Cabinet Light

T5L Under Cabinet Series Hardwired LED Undercabinet Fixture

Page 1 of 2 8060797

Safety Precautions

Read all safety precautions and installation instructions carefully

before installing or servicing this fixture. Failure to comply with

these instructions could result in potentially fatal electric shock

and/or property damage.

It is recommended that a qualified electrician perform all wiring. This

fixture must be wired in accordance with all national and local

electrical codes.

Do not handle an energized fixture or attempt to energize any fixture

with wet hands or while standing on a wet or damp surface or in

water.

Make sure that the power source conforms to the requirements of the

fixture. (See labels on fixture housing).

To reduce the risk of electrical shock, and to assure proper operation,

this fixture must be adequately grounded.

Do not touch LED light engine or heat-sink.

 12-inch minimum spacing distance from luminaire

required for all objects located under fixture.

This fixture is to be used for general indoor lighting in dry locations

only.

This fixture is dimmable. The following dimmers are approved for

use to achieve smooth dimming down to 10% of full scale:

Leviton – 6633, 6681, 6621-WWP, 6631-WWP, IPX06-1,

Lutron – TG-600P, TG-603P, AY600P, MACL153MH, SELV-300P,

DVCL-153P,GL600H,SFTU5A3P, S600P, SCL-153PH

Legrand / Pass & Seymour – T600WV, WS700TCCCVG

Cooper – 6013W

Assembly Instructions

1. Preparation for Installation

A. Disconnect electrical power before installing or servicing any part of this fixture.

B. Determine the best location for the fixture, by dry fitting to ensure proper placement.

C. This fixture has been designed to be (Hardwired), depending on your local NEC code power

will need to be brought to the fixture by your electrician with Romex NM-B,BX Cable or

Conduit.

D. Once power has been brought to the fixture location proceed to step 2.

Fig.1

2. Hardwire Installation Preparation

(Skip this step if using Cord to Outlet or Link-to-Fixture Installation to Power Unit)

A. Place fixture on a clean flat surface, remove frosted white Poly carbonate diffuser, disengage cover plate with your thumbs and tilt open .

B. Remove appropriate 3/8” diameter knockout for supply wiring entry.

C. Determine appropriate connector:

i) BX/Romex NM-B Cable connector is included(Ref Fig.2).

Fig. (2)

ii) Flexible conduit BX (AC) 3/8”trade size cable (8) (not

included).

iii) Anti-short bushing (not included Ref Fig 3).

Fig. (3)

D. Insert cable connector (3) into the housing hole opening. Secure it with the nut.

E. Trim away approximately 7: inches of the BX amour (using a BX cutter ( Not include). Push the exposed wires (hot, neutral and ground)

through the anti-short bushing and slide this bushing all the way down the exposed wires, and insert it into the end of the cable, this will

ensure that the wires will not get nicked, as shown in fig ( 3)

F. Follow the directions below for mounting and proceed to Hardware Installation Complete.

Fig 4.

Summary of content (2 pages)

PAGE 1
T5L Under Cabinet Series Safety Precautions Read all safety precautions and installation instructions carefully before installing or servicing this fixture. Failure to comply with these instructions could result in potentially fatal electric shock and/or property damage. It is recommended that a qualified electrician perform all wiring. This fixture must be wired in accordance with all national and local electrical codes.
PAGE 2
T5L Under Cabinet Series Hardwired LED Undercabinet Fixture 3. Hardwire Installation Completion a. b. c. d. e. f. There are 3 wires that are in the wire channel that are used to connect the fixture to the branch circuit. Connect the Green ground input supply wire to the fixture Green ground wire. Do this by inserting it into the open hole in the push-in wire connector (included) that is attached to the Green ground wire in the fixture. Connect the White input supply wire to the fixture White wire.