User Manual

ManualsBrandsAFX Racemasters ManualsHobby4-Way Split Race Set

CAUTIOII

ILECTRICALLY

OPERAIED PRODUCI

NOT RECOI4I\4ENDED FOR

CHILDRIN UNDER 8 YIARS

OF AOE AS

WlTl.l ALL ELICTRIC PRODUCIS

PRECAUT|Ol\lS

SHOULD

OBSIRVED DURIl'lc llANDLINO

AND

U$E TO PRIVEIIT

ELICTRIC

SHOCI(

PARENTS

PLEASE

N()TE

: lT lS

REC0MMENDED

THAT

THIS T()Y

BE PERI()DICALLY

EXAMINED

F()R

ANY

POTENTIAL HAZARDS

AND

SHOULD N()T BE

USED

UNTIL APPROPRIATE

REPAIRS

ARE

MADE.

P0wER

PAcK RATTNG,

|H;irlillivAc,

6012, 0.12A

The

Fut'ure of Racing,

OWNER'S MANUAL

TOTY'

I . cAUTroN:

uNpLuc

powER pAcK

BEFoRE

CLEANING TRACK

Always

clean the track before

you

start

racing.

Use an

eraser to clean the l?ack Rails,

then wipe away residue

. with

a clean dry cloth.

Blow

out any deposits that may have fallen in

the

track

grooves.

You may

also use the special track

pad provided

or a

coin to clean the Track Rails.

Simply

lay

a coin flat

the Rails

and

polish

until shiny.

NEVER

use steel wool to clean

the

Track.

Here are

a few maintenance

'tems

you

may need which

are

not included

this sel

Eraser

Dry

Cloth

Cellophane Tape

Coin

Toothpick

Small Screwdriver

NOTE: THE

2.WAY RACING PLUG ALLOWS

YOU TO

CHANGE

DIRECTION

TRAVELI FLIP

THE PLUG

OVER TO

REVERSE

FACING DIFECTION.

On sets using Lapometers,

inserl

the

plug

with the

arrow

pointing

the same direction as the

arrows

the

Lapometer.

REMEMBER:

Always

disconnect

Power

Pack when not

in. use

Never

pull

wires. Always remove

connections

pulling

the Plug.

Slide the

Accelerators Plugs into

the Terminal

Track.

Slide the Power Pack

2-Way

Racing Plug into

the

Choose

layout

from

the Layout Sheet.

Assemble

the straight

or curved track on a flat,

clean

surface. Do not

assemble Track

on carpeting.

Push

the

pieces

of Track together

until they

lock

place.

Asseml:le

pieces

Track

to form the layout

your

choice.

Terminal

Track

as shown.

Plug

the Power Pack

into

10-120 Volts,

AC).

Accelerators

Terminal Tiack

Power Pack

Guide

Slot

Squeeze the Trigger

on the

Accelerator

make

the car

accelerate.

The

you

squeeze

the

Trigger, the

faster

the car runs!

To reduce

speed, simply decrease

pressure

on the Trigger

Releasing

the

Trigger

stops

the car.

electrical wall

outlet

Pull the

pieces

apart

to drsassemble

5..

Snap the Trestles together as shown.

Attach the Trestles

to Track

as needed.

Place

cars

Track.

Make sure Guride

Pin fits into

Slot on Track.

NOTE:

Operate

only one car

per

lane.

Attach

a Guardrail to each curve section by

placing

the

Guardrail Tabs under the Track, then snapping up into

place.

Bottom of

Track

Trestle

etP

^<2q

t4/

)2:,=-

!-----'-

Accelerator

Plugs

2-Way

Racing Plug

Trigger

Accelerator

Summary of content (5 pages)

PAGE 1
. CAUTIOII ILECTRICALLY OPERAIED PRODUCI NOT RECOI4I\4ENDED FOR CHILDRIN UNDER 8 YIARS OF AOE AS WlTl.l ALL ELICTRIC PRODUCIS PRECAUT|Ol\lS SHOULD BE OBSIRVED DURIl'lc llANDLINO AND U$E TO PRIVEIIT ELICTRIC SHOCI( The Fut'ure of Racing, PARENTS PLEASE N()TE : lT lS REC0MMENDED THAT THIS T()Y BE PERI()DICALLY EXAMINED F()R ANY POTENTIAL HAZARDS AND SHOULD N()T BE USED OWNER'S MANUAL UNTIL APPROPRIATE REPAIRS ARE MADE. TOTY' a I . . |H;irlillivAc, . . . o Eraser .
PAGE 2
The Fufure of Rocing, Clean i ng/General Mai ntenance TRACK Use an Eraser to clean all Track Rails. Wipe away residue with a clean dry cloth. You can also lay the special Track Pad provided or a coin flat on the Rails and rub until Rails are shiny. Blow into the grooves to remove any small particles. Periodically wipe tracks with a clean cloth to rernove excess dust. A. CLEAN TIRES & TRACK -\rs(\-ss)-S\=rf.: /' Track Rails Coin TIRES Place a strip of cellophane tape on a table as shown.
PAGE 3
Performing aTune-Up To keep your car running in top performance, here's the mechanics guide to AFX tune-ups. A pair of spare shoes and springs are included. Ask your Toy or Hobby Dealer for the, AFX Tune-Up Kit (No. 8634) which includes all the parts you need for a complete tune-up. 4. NOTE: Before yoii begin, place a piece of white paper under your work area to make pieces easier to ftnd. REPLACING REAR AXLE ASSEMBLY Kit, the Rear Axle'comes assembled with Gear Spacer and Crown Gear already in place.
PAGE 4
AFX' Super G-Plus* Chassis Exploded ViewParts ldentification Fis Fig. C NOTE: Magnets have a white marking on one side. White marking is to be facing up away from the bottom of the chassis. Fig. A Body Retainer F-1 INDY Bodies (Do not require this bracket to be used!) Motor Brace l):; ^.J---rsl)e-F Pinion Gear Shoe Spring REMOVING/REPLACING MOTOR First remove the magnet retainer trom the rear of the chassis. A. Then remove rear axle assembly and shield.
PAGE 5
IMPORNT RE USE DUE TO THE ATMOSPHERE A THIN FILM MAY BUILD UP ON THE TRACK SURNACE. THEREFORE, FOR OPTIMTIM PERFORMANCE IT IS IYECESSARY TO CLEAN THE TRACK BEFORE USE - SEE INSTRUCTIONS. r Printed on recycled paper.