User`s guide

iI_ ii_i i
: i i i I
W
il__iii_i_i_i!I_ii_ii_!!_i_
i ii
i / _ii
2.0 AS rev 1.2.indd 10-11
A
B
C
D
FLATWASHER(C)
Qty:12
(_ NYLON
NUT(E)
Qty:2
BOLT(F) _ LOCKWASHER(L)
25 nlm _ Qty:2
Qty:10
BOLT(M) BOLT(N)
_ 65mm (_ 25mm
Qty:2 Qty:2
CHROMEWASHER(U)
Qty:2
SEATHEADPAD
FLATWASHER
SEATBACKADJUSTMENTBAR
SEATBACKPAD
\
SEATBOTTOMPAD \
NYLON
NUT
BOLT
FLATWASHER(C)\
CENTERSUPPORT
FRAME
jjfi
BOLT(F)
BOLT(N)_
FLAT _-. SEATBACK
WASHER(C) _
ADJUSTMENTPiN
jjJJ
•r_ j S
SEATBOTTOM /.................."-_
ROLLER
ADJUSTMENTBAR BOLT(M) ;HROMEWASHER(U)
LOCKWASHER(L)
LEGROLLER
OpenHARDWAREBAG4. SUPPORTTUBE _ BOLT(F)
WATER
BOTTLE
HOLDER
Attach SEATHEADPADtoCENTER
SUPPORTFRAMEusing4 BOLTS(F)and4 FLATWASHERS(C),as shownin diagram.
Install SEATBACKADJUSTMEHTPIN in CENTERSUPPORTFRAME.(Fullythreadinto
CENTERSUPPORTFRAMEafter SEATBACKAD]USTMEHTBAR is installed.)
Attach SEATBACKPADto SEATBACKAD]USTMEHTBARusing4 BOLTS(F)and 4 FLAT
WASHERS(C),and insert into CENTERSUPPORTFRAMEas shownin diagram.
E
Attach SEATBOTTOMPADto SEATBOTTOMADIUSTMEHTBARusing 2 BOLTS(M) and 4
FLATWASHERS(C) and 2 NYLONNUTS(E), and insert into SEATWELDMENTas shown in
diagram.
F InstallFOAMROLLERSontoLEGROLLERSUPPORTTUBEusing2 BOLTS(F),2 LOCK
WASHERS(L)and 2 CHROMEWASHERS(U),as shownin diagram.
G AttachWATERBOTTLEHOLDERtoCENTERSUPPORTFRAME using2 BOLTS(H).
tt Tightenall hardwarein Step4.
A
B
C
D
E
F
G
H
FLATWASHER(C)
Qty:8
_ YLON
NUT(E)
Qty:4
(_ FLATWASHER(I) _ NYLON
Qty:4 NUT(K)
Qty:2
BOLT(0)
lOOmm
Qty:2
BOLT(P)
_._) 70mm _-
Qty:2
RUBBER
BUMPER
Qty:2
BOLT(Q)
40 mm
Qty:2
OpenHARDWARE BAG 5.
AttachLOWERMOUNTINGBRACKET(after
removingpre-instafledguiderodbolts)toBASE
FRAMEin desiredlocation,using2 BOLTS(P),
4 FLATWASHERS(C)and 2 NYLONNUTS(E).
NOTE:Referto page25 for mountingpositions.
Position each GUIDERODso that the mounting
holes are in the upperposition, and insert
GUIDERODSinto corresponding sleeves in
LOWERMOUNTINGBRACKET.
SlideI UPGRADE SPACER and thenslide]
RUBBER BUMPER ontoeachguiderod,as
shown in diagram.
Install each WEIGHTPLATEonto guide rod as
shown in diagrarn. Ensure than the weight pin
selector slot is positioned downward and in
same direction.
Install BAYONETonto GUIDERODSas shown in
diagram.
Re-install GUIDEROD bolts intoLOWER
MOUNTINGBRACKET.
Instafl UPPERMOUHTIHGBRACKETto topof
GUIDERODS,as shownin diagram,using2
BOLTS(Q),4 FLATWASHERS(I) and 2 NYLON
HUTS(g).
UPPERMOUNTINGBRACKET
\
FLATWASHER(i)\
NYLONNUT(K)
BOLT(0)
j/ UPPER
PULLEY
ASSEMBLY
BOLT(Q)
/
\ FLAT
WASHER(I)
_-BAYONET
WEIGHT
/ PLATES
BASEFRAME
UPGRADE
SPACER
!
\
LOWERMOUNTING
BRACKET
FLATWASHER (C)
NYLONNUT(E)
AttachUPPERMOUHTIHGBRACKETtoUPPERPULLEYASSEMBLYusing2 BOLTS(0),4
FLATWASHERS(C),and 2 NYLONNUTS(E).
NOTE..Ensurethat the UPPERMOUHTIHGBRACKET'spositioncorrespondsto theposition
of the LOWERMOUNTINGBRACKETbeforesecuringit to the UPPERPULLEYASSEMBLK
] Tightenall hardware.
/
iii _ i i
ii _ _ii ii
12/28/07 10:16:08 AM