R AT-215 Owner＇ s Manual
Owner’s Manual for Professional Remote Dog Trainer AT-215 www.aetertek.
System Included------------------------------------------1 Quick Start--------------------------------------------------------2,3 Trouble Shooting----------------------------------------------- 4,5 Training Tips--------------------------------------------------6 Safety Guidance---------------------------------------------------7 Information for Terms of Use & Limitation of Liability--------8 Warranty Card--------------------------------------------------9,10
AT-215 System Included R Professional Dog Trainer AT-215 Transmitter Antenna Receiver Long correction prongs Short correction prongs Test Kit Collar Charger Antenna Receiver Transmitter Long correction prongs Short correction prongs Test Kit Collar Charger -01-
Quick Start 1 b 2 Step2: Open the transmitter's battery cover, and install the 9V battery into the transmitter. Match the + and - on batteries to the diagram inside 5 appropriate metal prongs onto the receiver till securely attached. -02- A:Press and hold on On/Off button until the Red LED light stay in solid. a Step 3: Screw in the 3 Step 4: Charge the receiver. A Red LED light of the receiver will turn on during charging . Charge port When done, the Blue LED will Blue LED light light up.
Quick Start The 1st dog Both dogs The 2nd dog Step 6: Check the Function buttons (vibrate, shock and strong shock). Press the Vibrate button, the receiver will vibrate. To test the shock, Cap the shock test kit on the metal prongs, push the shock button. If the bulb lights up, the shock function is ok. Shock Strong shock Step7: Adjust shock intensity. Press the shock button will produce weaker shocking effect, while the strong shock button will produce stronger shocking effect.
Trouble Shooting A：Transmitter /Receiver runs out of batteries quickly. 1：Make sure the charger and Transmitter/Receiver are securely connected. 2：Charge it up to 3 hours or above. B：Transmitter doesn't work. R Professional Dog Trainer AT-211 Replace the 9v dry battery with a new one or recharge the Transmitter. C：Transmitter can't match Receiver successfully. 1：Make sure the intensity level is not on ZERO. 2：Check whether the antenna is installed correctly or not.
Trouble Shooting R H: What's the rubber cap outside of charging port for? It prevent dust or water from coming into the charging port effectively. You need to plug the cap into the charging port tightly when charging is done.
Training Tips R This product is intended to support behavioral training and is not designed to be used without necessary interaction. Always praise your dog for good behavior. Verbal commands with positive reinforcement will contribute to be success of your training and will achieve the fastest, most desirable results possible. Professional Dog Trainer AT-215 The recommended age for training is a minimum of 6 months, provided that dog has the attention span and capability to lean basic commands.
Safety Guidance R 1. It is forbidden to open the receiver in case of breakage of the machine or harm the waterproof Professional Dog Trainer AT-215 feature. Otherwise it will violate warranty rules. 2. In order to guarantee submersible feature, the waterproof rubber charging lid should be plugged in tightly. 3. Only use the supplied adaptor to charge the receiver, otherwise the receiver will probably be damaged. 4.
Information for Terms of Use & Limitation of Liability 1. Terms of Use This product is offered to you conditioned upon your acceptance without modification of the terms, conditions, notices contained herein. Usage of this product implies acceptance of all such terms, conditions, and notices. R Professional Dog Trainer AT-215 2. Proper Use This product is designed for use with dogs where training is desired. The specific temperament of your dog may not work with this product.
Warranty Card Thank you for purchasing our dog trainer, one of the best training systems available for training your dog. Aetertek warrant the product to be free from defects in material and workmanship, arising under normal use for a period of 1 year from the date of original purchase when brand new. Misuse, loss or improper handling is not covered.
2. If defected machine have been proven out of warranty for following reasons, we will charge maintenance/repair fee: A: Warranty time expires. B: Damages caused by injudicious operation or some irresistible external forces (such as : flood, fires, earthquakes, lighting, typhoon, etc.). C: Damages caused by not abiding the clauses for operation, maintenance or storing the product in the user's manual. D: Repaired, re-assembled, or changed components or circuits by user.
