Step by Step Guide

A318/319/320/321
Profesional
Step-By-Step Tutorial
Vol
6
06-01- 42
11. Dezember 2018
85
OVERHEAD
SIGNS
12
SEAT BELT SIGNS / NO SMOKING = ON
ON
CoP
For Seat Belts also AUTO is OK
86
PEDESTAL
THR LEVER
4
LEVERS
CHECK IDLE
87
PEDESTAL
P. BRAKE
7
PARKING BRAKE
SET to ON
CoP
P3D: CTRL + . (period)
88
MCDU2
MAIN MENU
GND SERV.
TRAFFIC CONES
REMOVE
CoP
89
MCDU2
MAIN MENU
GND SERV.
WHEEL CHOCKS
REMOVE
CoP
90
EFIS
AP SETTING
2
BARO REF
SET / X CHECK (Read out)
CoP
91
PEDESTAL
XPDR
TRANSPONDER
AUTO
CoP
92
OVERHEAD
EXT. LIGHTS
9
BEACON
ON
CoP
Checklist complete
31.
DOORS / START CL: Closing left side passenger doors as well as cargo doors are blocked when pax
boarding and cargo loading (Settings MCDU LOAD/FUEL MENU) is ongoing. Checklist only starts if pax
boarding and cargo loading (Settings MCDU LOAD/FUEL MENU) is completed = are green.
32.
PARKING BRAKE: The parking brakes were OFF when the “COLD DARK” aircraft state was loaded. Now
they are set to ON.
33.
TRAFFIC CONES: Are automatically removed without call.
34.
WHEEL CHOCKS: Are automatically removed without call
35.
BARO REF: As we are flying with “Fair Weather” it means that in Frankfurt there will be no surface
winds and for takeoff the runway 18 is in use. The air pressure currently is 1013 hPa and we have a
temperature of 15 degrees C. As this is the “standard value” nothing must be done. If the air pressure
is different the Copilot will automatically set the right value.
5.7 Engine Start
GSX:
Open GSX (CRTL+F12) and select in GSX = 1 – Nose right / Tail left.
During pushback you can start the engines according to #97 - #101. The settings will be confirmed by
the Pilot and the Copilot. When pushback has been finished set parking brake to ON and proceed with
chapter 5.8 .
If no pushback is required, then please use the respective GSX function and set the checklist GSX PUSH
function (please see 4.6.3) to NO. After GSX has finished its procedure continue and select the “Engine
Start w/o Pushback” checklist and start it (5.7.2.). The reason is that GSX are closed programs and we
cannot get any information when to start the Engine Start checklist if there is no “moving” aircraft.
Engines can either be started during or after pushback (if necessary). Therefore also 2 different checklists are
available in the MCDU MENU – Checklists. Please select the one you want to use by clicking on the respective LSK.
5.7.1 Engine Start with Pushback
ENGINE START – with pushback
NO.
PANEL
ACTION
REMARK
TYP
PART (Name)
PART (No.)
PF (PILOT FLYING)
PM (PILOT MONITORING)
93
Settings
MCDU
MAIN MENU
CHECKLIST
SELECT: “START WITH PUSH” = LSK5L
Starts next Checklist / Co-Pilot - if selected
94
Settings
MCDU
SELECT TAXIWAX DIST and PB DIRECTION
SET
95
Settings
MCDU
START PUSHBACK
START
96
„Flight Deck to Ground“
GROUND: „Go ahead“
97
„We have ATC clearance“
GROUND: „Roger“
98
„Confirm ground equipment = clear”
GROUND: “Clear”
99
“Starting pushback”
GROUND: “Roger”
100
PEDESTAL
P. BRAKE
7
PARKING BRAKE = OFF
SET to OFF
P3D: . (period)
101
GROUND: “OK. Starting Pushback”
102
PEDESTAL
ENGINE
5
ENG MODE SEL
IGN START
103
PEDESTAL
ENGINE
5
MASTER SW 2
ON
104
MAIN PANEL
E/WD
5a
No. 2 RUNNING UP
CHECK
105
PEDESTAL
ENGINE
5
MASTER SW 1
ON
Engine 2 N1 > 20%
106
MAIN PANEL
E/WD
5a
No. 1 RUNNING UP
CHECK
107
When in Position: Stop Pushback
STOP (SHIFT + P)
108
GROUND: „Pushback complete”
109
PEDESTAL
P. BRAKE
7
PARKING BRAKE
ON
P3D: CRTL +.(period)
110
GROUND: “Have a good flight” – CL complete