Installation Guide Manufactured for Aero-Spa™, LLC E-Mail: info@aero-spa.net Web: www.aero-spa.
For outdoor use only! WARNING Pool care and sanitizing is the sole responsibility of the owner. In some cases a residual sanitizer must be present to minimize cross contamination. Pools/Spas are not intended to treat infections. Never allow use of pool if you are unable to verify the condition of open sores, wounds, lesions, cuts, sores, abrasions, boil, etc. or infections of any type exist. The best industry practice is to maintain a minimum of 2 PPM residual chlorine sanitizer in the water at all times.
Operation and Precautions IMPORTANT SAFETY INSTRUCTIONS Proper installation and usage of your Aero-Spa™ Ozone Generator is your responsibility. Read and follow this Installation Guide carefully for important installation, operation and safety information. Basic safety precautions should always be followed, including but not limited to the following: Read and follow all instruction. Never operate Aero-Spa™ equipment indoors.
Equipment Identification 1) Remove the equipment from the packaging. Care must be taken when handling the components. Do not drop the generator or sintered diffuser, as they are fragile. a) Identify the equipment components: Installation Guide, Safety/Warning Labels, Ozone Tube, and Sintered Diffuser (Figure 1). Please note that your product may vary from photos in this installation guide.
2) Equipment Set-up For best results it is highly recommended that the pool be thoroughly cleaned to remove residual dirt and contaminants prior to installation of the Aero-Spa™ system. Figure 2 a) Set the equipment on a level solid spacer block that is at least 2 – 3/8” thick and at least 10’ from the pool that is not prone to flooding (equipment is weather proof but not waterproof) figure 2.
Improper installation of the grounding plug can result in a risk of electric shock. If repair or replacement of the cord or plug is necessary, do not connect the grounding wire to either flat blade terminal. The wire with insulation having an outer surface that is green Figure 6 with or without yellow stripes is the grounding wire. Check with a qualified electrician or serviceman if the grounding instructions are not completely understood, or if in doubt as to whether the product is properly grounded.
Maintenance and Care This product has no user serviceable parts. If service is required, call or return the product to an authorized service representative. Attempts to service the ozone generator will void the 30 day customer satisfaction policy and Limited Warranty and expose the user to electrical shock which may cause severe injury or death. Keep the area around the product free of leaves and other debris.
TROUBLESHOOTING Aero-Spa™ not running 1. Reset GFCI breaker. If this problem persists replace GFCI breaker 2. Reset circuit breaker at house fuse panel. If this problem persists call Aero-Spa™, LLC 3. If these steps do not solve the problem call Aero-Spa™, LLC Water is cloudy 1. Increase the run time cycle 2. Repeat step 1 until water clarity improves 3. If these steps do not solve the problem call Aero-Spa™, LLC No bubbles coming from sintered diffuser 1. Verify Aero-Spa™ is running 2.
Brown ring at water line 1. This is normal when the water used to fill the pool has high iron content. Using “rust or stain remover” solution, wipe the rust stain with damp sponge containing rust or stain remover. Rinse sponge in solution periodically. 2. If these steps do not solve the problem call Aero-Spa™, LLC Light scale on surface 1. This occurs when the water used to fill the pool is hard. Using a sponge or “Scouring pad” pad, wipe surface to remove scale.
CUSTOMER SATISFACTION POLICY We are confident that the Aero-Spa™ process will maintain the desired water quality in your pool. If during the first 30 days you are not satisfied with the water quality in your pool you can return the Aero-Spa™ product to us for the refund of the purchase price. To be eligible to receive any refund under this Customer Satisfaction Policy you must contact us by telephone, e-mail or in writing within the time specified above, from the date of your invoice.
LIMITIATIONS MAY NOT APPLY TO YOU. For service, questions or to make a warranty claim, contact Aero at W300 N7706 Christine Lane, Hartland, Wisconsin, 53029, visit our website at www.aero-spa.net or e-mail us at info@aero-spa.net. If Buyer is making a warranty claim, please provide a description of the nature of the problem. Alternatively, call the following toll-free number to obtain further warranty instructions: 1-877-254-7093.
