Operation Manual

11
F.10 v.2 OPERATING MANUAL
© 2002 Design, 2011 Doc. No. 12-7260-r01 (4/19/11)
WATCH CDT (COUNTDOWN TIMER)
Once set ON, the Timer will run in the background until it counts down to 0:00, or it is set OFF, or a Dive is made at which time it will default to OFF
and the value previously set.
When a set Countdown Time reaches 0:00, the Audible Alarm will sound and the warning LED will flash, unless it is set Off.
Watch CDT Status, information includes (Fig. 13):
> Graphic TIMR.
> Remaining CD Time (hr:min) if running, or the Time set if it was set and not yet started, or 0:00 if no time was previously set or none is remaining
after running.
> Graphic OFF (or ON), flashing.
• S (< 2 sec) to toggle between OFF and ON.
• A & S (2 sec) to access Set CDT.
• M (2 sec) or no buton (2 min) to revert to Watch Main.
Set Watch CDT, information includes (Fig. 14):
> Graphics TIMR and SEt.
> Timer setting (hr:min) TIME icon, Hour digits flashing.
• S (hold) to scroll upward through the Hour Set Points from 0: to 23: at a rate of 8 per second in 1 Hour increments.
• S (< 2 sec) to step upward through the Hour Set Points one at a time.
• M (< 2 sec) to step back through the Hour Set Points one at a time.
• A (< 2 sec) to save the Hour setting and flash the Minute digits.
• S (hold) to scroll upward through the Minute Set Points from :00 to :59 at a rate of 8 per second in 1 Minute increments.
• S (< 2 sec) to step upward through the Minute Set Points one at a time.
• M (< 2 sec) to step back through the Minute Set Points one at a time.
• A (< 2 sec) to save the Minute (and full Timer) setting indicated by the graphic OFF flashing in place of SEt.
• S (< 2 sec) to start the Timer (Fig. 15).
• M (< 2 sec) to advance to Chrono.
• M (2 sec) or no button (2 min) to revert to Watch Main.
CHRONOGRAPH (Stop Watch, Lap/Run Timer)
The Chrono is operational during Free Surface and Dive Modes as well as Watch Mode. Once started, the Chrono continues to run regardless of
which mode the unit is operating in until it is stopped or it reaches the max Run Time. It runs unseen in the background when not on display.
> Upon access to the Chrono Status screen, elapsed run time is displayed if previously started, or 0:00:00.00 (hr:min:sec.1/100th sec), flashing.
• S (< 2 sec) to start the Chrono/Run Timer which will start and begin counting up from 0:00:00.01 (Fig. 16) to 9:59:59.99 in increments of .01
(1/100th sec).
> During the first 4 seconds, the .01 (1/100th) second values will be displayed, then 2 dashes ( . - - ) will be displayed. The 1/100th values will be
recorded and displayed when Lap times are recalled.
• S (< 2 sec) to save additional Lap Times and start the next one (Fig. 17).
> After 9 Laps are recorded, additional Laps will replace Lap 9, shifting the others to lower Lap numbers, while discarding Lap 1.
> If total Run Time reaches 9:59:59.99, it will stop and save that time as a Lap. The S button will then have no effect.
• A (< 2 sec) to stop the Run Timer and recall Lap 1, displaying the graphic Lap1 (flashing) and the Lap 1 Run Time. Repeat presses will display
other Laps/Run Times (Fig. 18).
• A (2 sec) to stop the Run Timer and reset the Time to 0:00:00.00 (flashing).
• M (2 sec) or no button (2 min) to revert to Watch Main.
While the Chrono is running, it will remain on the screen until M is pressed to access the Watch Daily Alarm, or if in Free Mode (surface or dive) to
revert to the Main. It will then continue to run in the background.
Fig. 13 - CDT STATUS
Fig. 14 - SET WATCH CDT
Fig. 15 - CD TIMER
STARTED
Fig. 16 - CHRONO
LAP 1 STARTED
Fig. 17 - CHRONO
LAP 4 STARTED
Fig. 18 - CHRONO LAP
RECALL