LUCCI AIRFUSION RADAR DC CEILING FAN INSTALLATION OPERATION MAINTENANCE WARRANTY INFORMATION CAUTION READ INSTRUCTIONS CAREFULLY FOR SAFE INSTALLATION AND FAN OPERATION.
Airfusion Radar Installation Instructions CONTENTS STALLAT 1|Page Page 2 Important information Safety precautions Page 3 Parts list Page 4-7 Installing the fan Page 7-10 Using your ceiling fan Page 11 Care & cleaning Warranty service Wobble Normal wear and tear Bump in the night Fan light Page 12 Trouble shooting checklist Page 13 Notes to installer Technical information Page 13-15 Warranty conditions
Airfusion Radar Installation Instructions IMPORTANT INFORMATION – PLEASE READ PRIOR TO INSTALLATION Congratulations on purchasing the latest in energy saving ceiling fans. This Airfusion Radar fan runs on DC (direct current) power which gives it the benefit of being super energy efficient whilst still maintaining high volume air-movement and silent operation. Energy saving - The DC motor is the latest technology in fan design.
Airfusion Radar Installation Instructions PARTS LIST Unpack your ceiling fan carefully. Remove all parts and hardware. Place the fan motor on a cloth or soft surface to avoid damaging the finish. • Do not lay the motor housing on its side – the decorative housing may become bent or damaged. • Verify that all parts are present before starting assembly. • Check the packaging carefully for missing parts. Examine all parts. You should have the following: Fig.
Airfusion Radar Installation Instructions INSTALLING THE FAN TOOLS REQUIRED: - Phillips / Flat head screwdriver - Pair of pliers - Adjustable spanner - Step ladder - Wire cutter - Wiring, supply cable as required by local provincial and national wiring codes and regulations. INSTALLING THE MOUNTING BRACKET The ceiling fan must be installed in a location so that the blades are spaced 300mm from the tip of the blade to the nearest objects or walls.
Airfusion Radar Installation Instructions HANGING THE FAN MOTOR ASSEMBLY • Lift the fan assembly to the mounting bracket (1) and let the J-hook of the mounting bracket (4) go through the hole of the hanging plate and hang up the fan assembly (3). Fig. 3 • Connect the male and female connector together (2). • Complete the electrical wiring using the diagram below (Figure. 4). Fig. 3 Fig. 3 PREPARE AND COMPLETE THE ELECTRICAL WIRING --- WIRING DIAGRAM (Fig.
Airfusion Radar Installation Instructions INSTALL THE CANOPY COVER • Loosen 2 screws (2) from the mounting bracket. Fig. 5 • Loosen 2 screws (1) by half thread from the mounting bracket. Fig. 5 • Lift the hanging plate of the fan assembly up to the mounting bracket and let the L-shape slot on the hanging plate go through the screws (1) on the mounting bracket. Turn the hanging plate until it locks in place at the end section of the L-shape slot and secure it by tightening the two screws (2).
Airfusion Radar Installation Instructions LIGHT KIT Installation (Light kit - optional) NOTE: The light kit must be installed by a licensed electrician. NOTE: The light kit is available for selected ceiling fan models and as an optional light kit. 1. Remove the bottom cover from the shaft. 2. Remove the shinkable tube from the light wires connector. 3. For light kit installation, please refer to the light kit installation user guide. Fig.
Airfusion Radar Installation Instructions Setting DC Ceiling fan 2: • Turn off both ceiling fans 1 and 2 via the mains supply to the receiver. • Slide the cover of the battery compartment of the transmitter to access the DIP switches. This will be transmitter 2. • Change the position of the DIP switches in the remote transmitter 2, so that it will be different to transmitter 1. Fig. 8 • Install the 12V DC battery in the compartment. Please make sure the polarity of the battery is correct.
Airfusion Radar Installation Instructions 2 - FAN OFF BUTTON: ○ Press the button to turn the fan off. 3 - REVERSE FUNCTION BUTTON: ○ Press the button to activate the reverse running function. The fan must be operating to activate the reverse function. 4 - LIGHT CONTROL BUTTON: ○ Press the button to turn on/off the light. THE RECEIVER PROVIDES THE FOLLOWING LEVEL OF PROTECTION: • Lock position: the receiver has a built in safety feature to protect against obstruction during operation.
Airfusion Radar Installation Instructions B. Turn off the main supply to receiver more than 30 seconds and turn on the main supply to receiver again. Press and hold the SET button of remote for 6 seconds within 60 seconds of turning turn the power to the receiver. C. Press the buttons on the remote to run the fan. In general, performing point A, B, and C should repair the remote and receiver, and will allow full control of the fan. If not, please do the next step. D.
Airfusion Radar Installation Instructions NOTE: For your safety, a new receiver must be installed by a licensed electrician. NOTE: While repairing the DC ceiling fan remote and receiver is in process, the fan operates at highest speed with REVERSE mode automatically for 90 seconds and then operates with FORWARD mode for 90 seconds. During the paring process, do not press any key on the remote. CARE & CLEANING • • Periodic cleaning of your ceiling fan is the only maintenance required.
Airfusion Radar Installation Instructions TROUBLE SHOOTING CHECKLIST Always check the “Trouble Shooting Checklist” included in this booklet before calling for service. Unnecessary calls are inconvenient for all and can attract a service charge. WARNING: THE CEILING FAN MUST BE SWITCHED OFF BEFORE TROUBLE SHOOTING IS PERFORMED. TROUBLE PROBABLE CAUSES SUGGESTED REMEDY A. Fuse or circuit breaker blown. Check main and branch circuit fuses or circuit breakers. 1. Fan will not start B.
Airfusion Radar Installation Instructions TECHNICAL INFORMATION AIRFUSION RADAR SERIES DC FAN models RADAR 52” FAN Rated Voltage Rated power (motor) Battery for remote 220-240VAC 35W 1 x 12V 23AE WARRANTY CONDITIONS IN AUSTRALIA / NEW ZEALAND – Please refer to the separated WARRANTY STATEMENT. IN EUROPE – If you are a European customer please contact the retail outlet where the fan was purchased for a warranty service.
Airfusion Radar Installation Instructions warranty. Where the fan is pre-packed complete with a light, the light fitting will be covered by warranty to electrical defect. Tarnishing caused by climatic conditions and breakage of glasses is not covered by warranty. Globes/lamps are also not covered by warranty. All light fittings attached to the fan must be installed by a licensed electrician ensuring such attachments are complete and do not affect the fan’s performance.
