AEOTEC Engineering Specification Recessed Door Sensor 7
AEOTEC Engineering Specification Engineering Specification Recessed Door Sensor 7 Document No. SPEC-ZW187 Description This document mainly introduces the new generation AEOTEC Recessed Door Sensor. The content mainly includes its interfaces, accessories, features, specifications, quick start, and software function definition. Recessed Door Sensor 7 is a Z-Wave Plus v2 device with many advantages . Can be embedded inside t he wooden door or window.
AEOTEC Engineering Specification REVISION RECORD Version Date Brief description of changes 1 2019.07.24 First revision.
AEOTEC Engineering Specification Table of Content 1 INTERFACES & ACCESSORIES .......................................................................................................................................... 1 2 FEATURES & SPECIFICATIONS ......................................................................................................................................... 2 3 2.1 Structural Characteristics ......................................................................................
AEOTEC Engineering Specification 1 INTERFACES & ACCESSORIES Terminology Description Action Button Inside the Z-Wave Button Hole. Used for networking and resetting. LED Used for indicating the current state of the product. Magnet Change the sensor state via making the Magnet away or near.
AEOTEC Engineering Specification 2 FEATURES & SPECIFICATIONS 2.1 Structural Characteristics Parameter Value Product Identifier ZW187 Dimensions Main Sensor: Φ19.2×64mm Weight 30g Color White Magnet Sensor: Φ22×13mm Shell Material ABS Shell Fire-proof Level UL94 V-0 Waterproof and Dustproof Rated IP20 under IEC 60529 Usage For indoor use. Can be embedded inside the wooden door or window. Operating Temperature 32~104°F (0~40°C) Relative Humidity 8%~80% 2.
AEOTEC Engineering Specification Security Class Non-Security, S0, S2 Unauthenticated, and S2 Authenticated SmartStart Compatible Support. After powering on, SmartStart is auto activ ated if it ’s out of the Z-Wave network. Over The Air (OTA) Support. Firmware can be updated via RF. Multi Channel Device No Association Support. Refer to Section 4.7 Association Group Info. Factory Reset Support. Refer to Section 3.6 How to factory reset. Power-down Memory Support.
AEOTEC Engineering Specification 3 PRODUCT QUICK START 3.1 Important safety information Please read this Engineering Specification carefully for correct and effective use. Failure to follow the recommendations set forth by AEOTEC Limited may be dangerous or cause a violation of the law. The manufacturer, importer, distributor, and/or reseller will not be held responsible for any loss or damage resulting from not following any instruction in this guide or in other materials.
AEOTEC Engineering Specification 3.3 How to install the product The following extra things are needed for the installation: screwdriver, 19mm wide drill bit, drill driver, PVA glue, rubber hammer. 1. Drill a hole 65mm / 2.56inch deep in your door at the selected location with a 19mm / 0.75inch wide drill bit. 2. Drill a hole 15mm / 0.59inch deep in your doorframe at the corresponding location with a 19mm / 0.75inch wide drill bit. 3. Insert sensor into the hole you drilled in the door.
AEOTEC Engineering Specification 3. Remove the Pull Tab to engage the pre-installed battery. LED will become slow fade-in fade-out Red color for a few seconds which will indicate that its power is on. 4. Add Recessed Door Sensor 7 to your Z-Wave network; A. If your Z-Wave gateway supports SmartStart, Recessed Door Sensor 7 is SmartStart enabled allowing you to connect it to your Z-Wave gateway by scanning your device’s QR Code using your gateway's app.
AEOTEC Engineering Specification 3.5 How to remove the product from Z-Wave network 1. Set your Z-Wave Controller into its 'Remove Device' mode in order to remove the product from your Z-Wave system. Refer to the Controller's manual if you are unsure of how to perform this step. 2. Make sure the product is powered. 3. Click Action Button once; LED will become flash Red color for 5 seconds. 4. If Removing fails, it will extinguish, without slow fade-in fade-out Red color. 5.
