Technical data

ManualsBrandsAeon Labs Manualselectrical controlsSmart Energy Switch 3

AEO_SES3_EU

Inline Smart Energy Switch

Firmware Version : 2.25

Quick Start

A This is a Z-Wave actuator.

Inclusion and Exclusion are confirmed by a single click on the button. If the Aeon Labs Inline Smart Energy Switch is not included

into any Z-Wave network, the LED will be blinking continually.The device supports secure communication.

Please refer to the chapters below for detailed information about all aspects of the products usage.

Product description

The Aeon Labs Inline Smart Energy Switch is a Z-Wave light switch specifically used to enable Z- Wave commands and control

(on/off) a device that is connected to a standard Schuko Wall Outlet.

It can also report immediate wattage consumption or kWh energy usage over a period of time. The wireless module is powered

from the mains supplys. In the event of power failure, non-volatile memory retains all programmed information relating to the

units operating status. This device support secure communication when included by a controller that also supports secure

communication. The device will then send all commands as secure commands unless the receiving device can not accept them.

Then the command is send the normal way automatically.

Installation Guidelines

This device be plugged between every Standard-Schuko wall outlet and the electrical appliance with maximum load of 3500W. To

switch the plugged device on or off simply push the local button once or use a Z-Wave Controller. The status is shown by the

status LED at the device.

Summary of content (6 pages)

PAGE 1
AEO_SES3_EU Inline Smart Energy Switch Firmware Version : 2.25 Quick Start A This is a Z-Wave actuator. Inclusion and Exclusion are confirmed by a single click on the button. If the Aeon Labs Inline Smart Energy Switch is not included into any Z-Wave network, the LED will be blinking continually.The device supports secure communication. Please refer to the chapters below for detailed information about all aspects of the products usage.
PAGE 2
Behavior within the Z-Wave network I On factory default the device does not belong to any Z-Wave network. The device needs to join an existing wireless network to communicate with the devices of this network. This process is called Inclusion. Devices can also leave a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller will be turned into exclusion respective inclusion mode.
PAGE 3
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features. IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 … 255 the value sent in the application shall be the desired value minus 256. For example: to set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56.
PAGE 4
Value Description 0 Enabled parameter 91/92 (Default) 1 Disabled parameter 91/92 Minimum Change to send Report (Watt) (Parameter Number 91, Parameter Size 2) The value represents the minimum change in wattage for a Report to be sent . Value Description 0 — 32000 The value represents the minimum change in wattage. (Default 25) Minimum Change to send Report (%) (Parameter Number 92, Parameter Size 1) The value represents the minimum change in wattage Percent for a report to be sent.
PAGE 5
4 Meter Report for Watt 8 Meter Report for kWh Set 111‐113 to default (Parameter Number 110, Parameter Size 1) Value Description 0 Set to default (Default) 1 nothing Send Interval for Reporting Group 1 (Parameter Number 111, Parameter Size 4) Defines the time interval when the defined report of Reporting Group 1 is sent out.
PAGE 6
SDK 6.51.00 Device Type Slave with routing capabilities Generic Device Class Binary Switch Specific Device Class Binary Power Switch Routing Yes FLiRS No Firmware Version 2.25 6 (c) 2012 Z-Wave Europe GmbH, Goldbachstr. 13, 09337 Hohenstein-Ernstthal, Germany, www.zwaveeurope.