User's Manual
1.
2.
3.
4.
Put your primary controller into device removal mode.
Unlock your Sensor from the Back Mount plate and take the Sensor unit near
to your primary controller.
Press the Action Button on your Sensor.
If your Door Window Sensor is successfully removed from the Z-Wave network,
the RGB LED will become a colourful gradient for a few seconds and then turn
off. If the removing was unsuccessful, the RGB LED will be solid for 8 seconds
and then turn off, repeat the above steps.
Your sensor can be removed from your Z-Wave network at any time. You'll need
to use your Z-Wave network's main controller/gateway. To do this, please refer to
the part of their respective manuals that tell you how to remove devices from your
network.
If you want your Sensor as a non-security device in your Z-wave network, you
just need to press the Action Button once on Door Window Sensor when you
use a controller/gateway to add/include your Sensor. The green LED will be on
for 2 seconds and then the orange LED will fast blink for 10 minutes (if the Sensor
does not receive the Wake Up No More Info command from primary Controller) to
indicate the inclusion is successful.
Removing your Sensor from your Z-Wave network.
Security or Non-security feature of your Sensor in Z-wave network.
Including Door Window Sensor as a non-secure device:
Model number: ZW112.
Power supply: Rechargeable Lithium battery, 3.7 V, 500mAh.
Battery charger input: Micro USB port, DC 5V±0.5V, max 1A.
Operating temperature: 0°C to 40°C/32°F to 104°F.
Relative humidity: 8% to 80%.
Water proong: IP20 (Indoor use only).
Operating distance: Up to 492 feet/150 metres outdoors.
Technical specifications.
5
If your primary controller is missing or inoperable, you may wish to reset all of
your Door Window Sensor’s settings to their factory defaults. To do this, press
and hold the Action Button for 20 seconds and the green LED will be solid for 2
seconds and then be colourful gradient to conrm a success.
Your Door Window Sensor has a internal rechargeable lithium battery that will last
for 6 months on a full charge when it is in normal use condition. The charger’s
output should be a micro USB terminal with the specication of output DC 5V/1A.
When the Door Window Sensor is in charge state, the orange LED will be on. If
the orange LED is off and the green LED remains on, then it indicates that the
battery charge is complete.
In order to take full advantage of all functionality the Door Window Sensor, you
may want your Sensor is a security device that uses secure/encrypted message
to communicate in Z-wave network, so a security enabled controller/gateway is
needed for the Door Window Sensor to be used as a security device. You need
to press the Sensor’s Action Button 2 times within 1 second when your security
controller/gateway starts the network inclusion. The blue LED will be on for 2
seconds and then the orange LED will fast blink for 10 minutes (if the Sensor
does not receive the Wake Up No More Info command from primary Controller) to
indicate the inclusion is successful.
Factory Reset your Sensor.
Your Sensor’s battery.
Including Door Window Sensor as a secure device:
Warranty.
If you are in need of any technical support during or subsequent to your products’
warranty, please get in touch with our support team via http://aeotec.com/
support. The Company you bought this product from has also guaranteed to
assist you with any of your support needs, and you can also contact them for
accordingly.
This guarantee made by the company who you purchased the product from
includes the transfer of Aeon Labs’ full warranty to that Company. They’ve
guaranteed that they’ll be able to assist you, the Customer, with all technical
support and repair needs on our behalf.
Aeon Labs warrants to the original purchaser of Products, that is the Company
6
FCC NOTICE (for USA)
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT.SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY
TO OPERATE THE EQUIPMENT.
STORE INDOORS WHEN NOT IN USE. SUITABLE FOR DRY LOCATIONS. DO
NOT IMMERSE IN WATER. NOT FOR USE WHERE DIRECTLY EXPOSED TO
WATER.
This device may not cause harmful interference, and
This device must accept any interference received, including interference that
may cause undesired operation. This equipment has been tested and found
to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates,
1.
2.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Do not dispose of electrical appliances as unsorted municipal waste, use
separate collection facilities.
Warning
Certifications (regional):
Version: 501011200001-AA www.aeotec.com
Contact your local government for information regarding the collection systems
available.
uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Z-Wave and Z-Wave Plus are registered trademarks of
Sigma Designs and its subsidiaries in the United States and
other countries
FCC ID: XBAFT112
who you have purchased from, that for the Warranty Period (as dened below),
the Products will be free from material defects in materials and workmanship. The
foregoing warranty is subject to the proper installation, operation and maintenance
of the Products in accordance with installation instructions and the operating
manual supplied. Warranty claims must be made to the Company who you have
purchased from in writing within thirty (30) days of the manifestation of a problem.
Aeon Labs' sole obligation under the foregoing warranty is, at Aeon Labs' option,
to repair, replace or correct any such defect that was present at the time of
delivery, or to remove the Products and to refund the purchase price to Company.
The Warranty Period begins on the date the Products is delivered and continues
for 12 months. Any repairs under this warranty must be conducted by an
authorized Aeon Labs service representative and under Aeon Labs' RMA policy.
Any repairs conducted by unauthorized persons shall void this warranty.
Excluded from the warranty are problems due to accidents, acts of God, civil or
military authority, civil disturbance, war, strikes, res, other catastrophes, misuse,
misapplication, storage damage, negligence, electrical power problems, or
modication to the Products or its components.
Aeon Labs does not authorize any person or party to assume or create for it any
other obligation or liability in connection with the Products except as set forth
herein. Aeon Labs will pass on to Company all manufacturers’ Material warranties
to the extent that they are transferable, but will not independently warrant any
Material. Company will assist Customer with all warranty, repair, return and
technical support needs, Company must prepay shipping and transportation
charges for returned Products, and insure the shipment or accept the risk of
loss or damage during such shipment and transportation. Aeon Labs will ship
the repaired or replacement products to Company freight prepaid.Customer
and Company shall indemnify, defend, and hold Aeon Labs and Aeon Labs'
afliates, shareholders, directors, ofcers, employees, contractors, agents and
other representatives harmless from all demands, claims, actions, causes of
action, proceedings, suits, assessments, losses, damages, liabilities, settlements,
judgments, fines, penalties, interest, costs and expenses (including fees and
disbursements of counsel) of every kind (i) based upon personal injury or death or
injury to property to the extent any of the foregoing is proximately caused either
by a defective product (including strict liability in tort) or by the negligent or willful
acts or omissions of Customer or its officers, employees, subcontractors or
agents, and/or (ii) arising from or relating to any actual or alleged infringement or
misappropriation of any patent, trademark, mask work, copyright, trade secret or
any actual or alleged violation of any other intellectual property rights arising from
or in connection with the products, except to the extent that such infringement
exists as a result of Aeon Labs' manufacturing processes.
IN NO EVENT SHALL AEON LABS BE LIABLE FOR ANY INDIRECT,
INCIDENTAL, PUNITIVE, SPECIAL OR CONSEQUENTIAL DAMAGES,
OR DAMAGES FOR LOSS OF PROFITS, REVENUE, OR USE INCURRED
BYCUSTOMER, COMPANY OR ANY THIRD PARTY, WHETHER IN AN ACTION
IN CONTRACT, OR TORT, OR OTHERWISE EVENIF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. AEON LABS' LIABILITY AND CUSTOMER'S
EXCLUSIVE REMEDY FOR ANY CAUSE OF ACTION ARISING IN CONNECTION
WITH THIS AGREEMENT OR THE SALE OR USE OF THE PRODUCTS,
WHETHER BASED ON NEGLIGENCE, STRICT LIABILITY, BREACH OF
WARRANTY, BREACH OF AGREEMENT, OR EQUITABLE PRINCIPLES, IS
EXPRESSLY LIMITED TO, AT AEON LABS' OPTION, REPLACEMENT OF, OR
REPAYMENT OF THE PURCHASE PRICE FOR THAT PORTION OF PRODUCTS
WITHRESPECT TO WHICH DAMAGES ARE CLAIMED. ALL CLAIMS OF ANY
KIND ARISING IN CONNECTION WITH THIS AGREEMENT OR THE SALE
OR USE OF PRODUCTS SHALL BE DEEMED WAIVED UNLESS MADE IN
WRITING WITHIN THIRTY (30) DAYS FROM AEON LABS' DELIVERY, OR
THE DATE FIXED FOR DELIVERY IN THE EVENT OF NONDELIVERY. THE
INDEMNITY AND WARRANTY IN ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL
OTHER INDEMNITIES OR WARRANTIES, WHETHER EXPRESS OR IMPLIED,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE.