User's Manual

ManualsBrandsAeon Labs ManualsElectronicsSmart Dimmer 6,Dimmer,Dimmer 6

Model number: FT09

9-A02.

Max standby power: 0.8W.

USB output: DC 5V±5%, 1000mA.

Operating temperature: 0 to 40 .

C C

Relative humidity: 8% to 80%.

Supported load type: Incandescent bulbs, dimmable

LED bulbs, halogen bulbs with or without transformers.

Operating distance: Up to 100 feet/30 metres indoors or

390 feet/120 metres outdoors.

AC input:

Technical specications.

Version

Input Working band

230V 50Hz, Max: 2.5A 921.42MHz

220V 60Hz, Max: 2.5A 921.42MHz

220V 50Hz, Max: 2.5A 868.42MHz

230V 50Hz, Max: 2.5A 868.42MHz

230V 50Hz, Max: 2.5A 865.22MHz

230V 50Hz, Max: 2.5A 868.42MHz

125V 60Hz, Max: 2.5A

908.42MHz

Warranty.

The "Warranty Period" begins on the date the Products

is delivered and continues for 12 months.

Any repairs under this warranty must be conducted by

an authorized Aeon Labs service representative and

under Aeon Labs' RMA policy. Any repairs conducted by

unauthorized persons shall void this warranty.

Excluded from the warranty are problems due to

accidents, acts of God, civil or military authority, civil

disturbance, war, strikes, fires, other catastrophes,

misuse, misapplication, storage damage, negligence,

electrical power problems, or modification to the

Products or its components.

Aeon Labs does not authorize any person or party to

assume or create for it any other obligation or liability in

connection with the Products except as set forth herein.

Aeon Labs will pass on to Customer all manufacturers’

Material warranties to the extent that they are

transferable, but will not independently warrant any

Material.

Customer must prepay shipping and transportation

charges for returned Products, and insure the shipment

or accept the risk of loss or damage during such

shipment and transportation. Aeon Labs will ship the

repaired or replacement products to Customer freight

prepaid.

Customer shall indemnify, defend, and hold Aeon

Labs and Aeon Labs' affiliates, shareholders,

directors, officers, employees, contractors, agents

and other representatives harmless from all demands,

claims, actions, causes of action, proceedings, suits,

assessments, losses, damages, liabilities, settlements,

judgments, nes, penalties, interest, costs and expenses

(including fees and disbursements of counsel) of

every kind (i) based upon personal injury or death or

injury to property to the extent any of the foregoing

is proximately caused either by a defective product

(including strict liability in tort) or by the negligent or

willful acts or omissions of Customer or its officers,

employees, subcontractors or agents, and/or (ii) arising

from or relating to any actual or alleged infringement or

misappropriation of any patent, trademark, mask work,

of any other intellectual property rights arising from or

IN NO EVENT SHALL AEON LABS BE LIABLE FOR

ANY INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL OR

CONSEQUENTIAL DAMAGES, OR DAMAGES FOR LOSS OF

PROFITS, REVENUE, OR USE INCURRED BY CUSTOMER OR

ANY THIRD PARTY, WHETHER IN AN ACTION IN CONTRACT,

OR TORT, OR OTHERWISE EVEN IF ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES. AEON LABS' LIABILITY

AND CUSTOMER'S EXCLUSIVE REMEDY FOR ANY CAUSE OF

ACTION ARISING IN CONNECTION WITH THIS AGREEMENT

OR THE SALE OR USE OF THE PRODUCTS, WHETHER

BASED ON NEGLIGENCE, STRICT LIABILITY, BREACH OF

WARRANTY, BREACH OF AGREEMENT, OR EQUITABLE

PRINCIPLES, IS EXPRESSLY LIMITED TO, AT AEON LABS'

OPTION, REPLACEMENT OF, OR REPAYMENT OF THE

PURCHASE PRICE FOR THAT PORTION OF PRODUCTS

WITH RESPECT TO WHICH DAMAGES ARE CLAIMED. ALL

CLAIMS OF ANY KIND ARISING IN CONNECTION WITH THIS

AGREEMENT OR THE SALE OR USE OF PRODUCTS SHALL

BE DEEMED WAIVED UNLESS MADE IN WRITING WITHIN

THIRTY (30) DAYS FROM AEON LABS'S DELIVERY, OR THE

DATE FIXED FOR DELIVERY IN THE EVENT OF NONDELIVERY.

THE INDEMNITY AND WARRANTY IN ABOVE ARE EXCLUSIVE

AND IN LIEU OF ALL OTHER INDEMNITIES OR WARRANTIES,

WHETHER EXPRESS OR IMPLIED, INCLUDING THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE.

FCC NOTICE (for USA)

THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY

RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED

MODIFICATIONS TO THIS EQUIPMENT.SUCH MODIFICATIONS

COULD VOID THE USER’S AUTHORITY TO OPERATE THE

EQUIPMENT.

STORE INDOORS WHEN NOT IN USE. SUITABLE FOR DRY

LOCATIONS. DO NOT IMMERSE IN WATER. NOT FOR USE

WHERE DIRECTLY EXPOSED TO WATER.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

This device may not cause harmful interference, and

This device must accept any interference received,

including interference that may cause undesired

operation. This equipment has been tested and found

to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and

receiver.

Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

Consul the dealer or an experienced radio/TV

technician for help.

Do not dispose of electrical appliances as unsorted

municipal waste, use separate collection facilities.

Contact your local government for information

regarding the collection systems available.

Warning

Certications (regional):

Version:501009900001-AA www.aeotec.com

Z-Wave and Z-Wave Plus

are registered trademarks

of Sigma Designs and its

subsidiaries in the United

States and other countries

FCC ID: XBAFT099

Reset your Smart Switch.

Security or Non-security feature of your Smart

Dimmer in Z-wave network.

If at some stage, your primary controller is missing or

inoperable, you may wish to reset all of your Smart

Dimmer’s settings to their factory defaults. To do this,

press and hold the Action Button for 20 seconds and

then release it. Your Smart Dimmer will now be reset to

its original settings, and the RGB LED will be solid for 2

seconds and then start slow blinking as a conrmation.

If you want your Smart Dimmer as a non-security

device in Z-wave network, you just need to press the

Action Button once on Smart Dimmer when you use a

controller/gateway to add/include your Smart Dimmer.

In order to take full advantage of the Smart Dimmers

functionality, you may want your Smart Dimmer as a

security device that uses secure/encrypted message

to communicate in your Z-wave network, so a security

enabled controller/gateway is needed. You need to

press the Smart Dimmer’s Action Button 2 times within 1

second when your security controller/gateway starts the

network inclusion.

Aeon Labs warrants to the original purchaser of Products

that for the Warranty Period (as defined below), the

Products will be free from material defects in materials

and workmanship. The foregoing warranty is subject to

the proper installation, operation and maintenance of the

Products in accordance with installation instructions and

the operating manual supplied to Customer. Warranty

claims must be made by Customer in writing within thirty

(30) days of the manifestation of a problem. Aeon Labs'

sole obligation under the foregoing warranty is, at Aeon

Labs' option, to repair, replace or correct any such defect

that was present at the time of delivery, or to remove the

Products and to refund the purchase price to Customer.

in connection with the products, except to the extent

that such infringement exists as a result of Aeon Labs'

manufacturing processes.