User's Manual

Aeon Labs Home Energy Meter
(Z-Wave Home Energy Meter)
Accessory :
:
:
C
C
C
U
U
U
R
R
R
R
R
R
E
E
E
N
N
N
T
T
T
T
T
T
R
R
R
A
A
A
N
N
N
S
S
S
F
F
F
O
O
O
R
R
R
M
M
M
A
A
A
T
T
T
O
O
O
R
R
R
Introduction:
The Aeon Labs Home Energy Meter is a low-cost energy
meter for the entire home. It can wirelessly report
immediate wattage and kWh usage of the AC mains to a Z-
Wave gateway.
By taking advantage of the Z-Wave mesh network,
commands can be routed to their destination via
intermediary “listening” Z-Wave products. Products that are
Z-Wave certified can be used and communicate with other Z-
Wave certified devices.
Z-Wave Network Instructions:
The Aeon Labs Home Energy Meter must be paired (included)
into a Z-Wave network before it can receive Z-Wave
commands to report its energy usage. The home energy
meter can only communicate to devices within it’s own z-
wave network.
Note
: If the Home Energy Meter is not currently paired into a
Z-Wave network, the LED on the Home Energy Meter will
blink after pressing the button located near the batteries.
• Adding/Including/Pairing the Home Energy Meter
into a Z-Wave Network
1. Press the button on the Aeon Labs Z-Stick to begin the
Z-Wave inclusion process.
OR
Press the button labeled “Include” on the Aeon Labs
Minimote to begin the Z-Wave inclusion process.
Note
: To include the Aeon Labs Home Energy Meter
with other controllers, please consult the operation
manual for these controllers on how to include Z-Wave
products into an existing network. For instructions on
select partner gateways, visit www.aeon-
labs.com/support.
2. After placing 4 AA batteries into the Home Energy
Meter, press the button located near the batteries .
Troubleshooting: If the Aeon Labs Home Energy Meter was
not successfully included into any Z-Wave network, the LED
will blink after pressing the button near the batteries. If the
Aeon Labs Home Energy Meter was successfully included to a
Z-Wave network, the LED will be lit solid after pressing the
button.
• Removing/Resetting the Home Energy Meter from
your Z-Wave Network
1. Hold the button on the Aeon Labs Z-Stick to begin the
Z-Wave removal process.
OR
Press the button labeled “Remove” on the Aeon Labs
Minimote Stick to begin the Z-Wave removal process.
Note: To include the Aeon Labs Home Energy Meter
with other controllers, please consult the operation
manual for these controllers on how to include Z-Wave
products into an existing network. For instructions on
select partner gateways, visit www.aeon-
labs.com/support.
2. After placing 4 AA batteries into the Home Energy
Meter, press the button located near the batteries .
Troubleshooting: If the Aeon Labs Home Energy Meter was
removed from the Z-Wave network, the LED will blink after
pressing the button near the batteries. If the Aeon Labs
Home Energy Meter was not successfully removed from a Z-
Wave network, the LED will be lit solid after pressing the
button.
• Monitoring Energy Consumption
The Aeon Labs Home Energy Meter can report wattage
energy usage or kWh energy usage to a Z-Wave gateway or
controller when requested. If this function is supported by
the gateway/controller, the energy consumption will be
displayed in the user interface of the gateway/controller.
(The specific Z-Wave commands supporting energy
monitoring are the Meter Command Class and Multilevel
Sensor Command Class.) Please consult the operation
manual for these gateways/controllers for specific
instructions on monitoring the Home Energy Meter.
- 1 - - 2 - - 3 -
- 1 - - 2 - - 3 - - 4 -