21009-1 DigiSender ZX7 MODEL: DG458 ® 5.8GHz Quad Input Wireless AV Sender WATCH A VIDEO INSTALLATION & & TROUBLESHOOTING TROUBLESHOOTING GUIDE GUIDE Available Available online online at: at: www.aei.eu/video www.aei.
DG458 - DigiSender® ZX7 - 5.
DG458 - DigiSender® ZX7 - 5.8GHz Quad Input Wireless AV Sender Introduction Congratulations on purchasing the DigiSender® ZX7 - Quad Input 5.8GHz Wireless AV Sender. This product represents state of the art wireless audio and video technology and the most advanced Infra-Red relay technology at exceptional value for money. You can now enjoy DVD quality video and Hi-Fi stereo sound from your Satellite, Cable, Freeview, DVD or VCR in another room in your home.
DG458 - DigiSender® ZX7 - 5.8GHz Quad Input Wireless AV Sender STEP 1 - Unpack your DigiSender® ZX7 Aux 2 Input 4 Input 3 Aux 1 Input 2 DigiConnector™ 2 DigiConnector™ 1 Input 1 POWER All DigiSender® orders are computer weight checked when packed. However, it is a good idea to check all kit contents are present before proceeding with the installation.
DG458 - DigiSender® ZX7 - 5.8GHz Quad Input Wireless AV Sender STEP 2 - Install the DigiSender® ZX7 Transmitter The Transmitter will send the audio and video from up to four connected sources (your Satellite and DVD Player for example) to the Receiver, located in another room in your home. 1. 2. Connect DigiConnector™ 1 to your Satellite, Cable or Freeview box. Use the SCART socket labelled ‘TV’ or ‘OUT’. Connect any existing SCART lead into the rear of the DigiConnector™.
DG458 - DigiSender® ZX7 - 5.8GHz Quad Input Wireless AV Sender continued... Note: Try to avoid positioning the Transmitter directly on top of other electrical devices as this could lead to a poor picture. 5. 6. Connect the Power Supply Unit (PSU) to the socket labelled ‘PSU’ on the rear of the Transmitter. Connect the Power Supply Unit (PSU) to an available mains socket and switch on at the back of the Transmitter.
DG458 - DigiSender® ZX7 - 5.8GHz Quad Input Wireless AV Sender STEP 3 - Install the IR Systeme Technik™ Once set up correctly, the IR Systeme Technik™ will enable you to control your source equipment from the receiving location in your home. Because everyone’s set up is different there are many ways you can install the IR Systeme Technik™ and the various included accessories will help you in setting it up correctly.
DG458 - DigiSender® ZX7 - 5.8GHz Quad Input Wireless AV Sender STEP 4 - Install the DigiSender® ZX7 Receiver The Receiver will pick up the signals being sent by your Transmitter and output them to a connected TV. 1. 2. Locate a vacant SCART socket on the back of your receiving TV and insert the DigiSender® SCART cable. Ensure that the Audio/Video and Remote Relay Channel switches on the back of the Receiver are set to 1. 3. 4.
DG458 - DigiSender® ZX7 - 5.8GHz Quad Input Wireless AV Sender STEP 5 - Using the DigiSender® ZX7 1. 2. POWER Switch on the source equipment (Satellite, Freeview, DVD, VCR, etc.). Turn on the Transmitter and Receiver by pushing the Power button on the front of the units. The standby LED will change from red to green to indicate the unit is switched on. Alternatively press the POWER Power button on the DigiSender® Remote Control. 3. 1 2 4.
DG458 - DigiSender® ZX7 - 5.8GHz Quad Input Wireless AV Sender Using the DigiSender® ZX7 The DigiSender® Remote Control 1. POWER The POWER button will turn your DigiSender® ZX7 Transmitter or Receiver On or Off. 2. Input 1 The Input 1 button will select Input 1 on the Transmitter and Receiver. Input 1 will be what ever source equipment is connected to DigiConnector™ 1. For example, a Satellite, Cable or Freeview box. 3. Input 2 The Input 2 button will select Input 2 on the Transmitter and Receiver.
DG458 - DigiSender® ZX7 - 5.8GHz Quad Input Wireless AV Sender Using the DigiSender® ZX7 Basic Functions Turning the DigiSender® ZX7 On and Off To turn the DigiSender® ZX7 On, press the power button on the front of the Transmitter and Receiver. The red standby LED will light up green to indicate that the unit is switched on. To turn the DigiSender® ZX7 Off, press and hold the power button on the front of the Transmitter and Receiver for approximately 3 seconds.
DG458 - DigiSender® ZX7 - 5.8GHz Quad Input Wireless AV Sender Using the DigiSender® ZX7 Advanced Functions Changing the Audio/Video Channel The DigiSender® ZX7 features 4 Audio/Video Channels. Each of these Audio/Video Channels slightly changes the frequency on which the DigiSender® ZX7 operates. Because the Audio/Video Channel switch allows you to ‘fine tune’ the frequency on which your DigiSender® ZX7 operates, it is possible to overcome most interference and reception troubles that may occur.
DG458 - DigiSender® ZX7 - 5.
DG458 - DigiSender® ZX7 - 5.8GHz Quad Input Wireless AV Sender Troubleshooting Picture Problems Q: What do you see on your second television? The picture is present but poor quality POOR RANGE 1. The picture & sound quality is affected by the Transmitter and Receiver’s location. Try positioning them in different locations. The Transmitter and Receiver should be connected to a mains extension lead that can be moved. 2.
DG458 - DigiSender® ZX7 - 5.8GHz Quad Input Wireless AV Sender cont... I see a snowstorm effect or plain blue screen Switch OFF your DigiSender® RECEIVER. Q: What do you now see at the second TV? I now see a Black screen I still see a snowstorm or blue picture NOT RECEIVING SIGNAL WRONG TV CHANNEL SELECTED 1. Switch the DigiSender® Receiver back on. 2. Ensure the DigiSender® Transmitter is switched on. 3.
DG458 - DigiSender® ZX7 - 5.8GHz Quad Input Wireless AV Sender Troubleshooting Audio Problems I can see the picture but can’t hear anything. The sound is distorted. Q: What seems to be the problem with the sound? There is a buzzing sound present. It seems to get worse during on-screen menus or bright pictures. There is a hissing sound and the volume must be turned up high on the second TV to hear anything. Page 16 1. Disconnect both the Transmitter AND Receiver SCART cables.
DG458 - DigiSender® ZX7 - 5.8GHz Quad Input Wireless AV Sender Troubleshooting Problems Controlling the Source Equipment If you have any difficulty operating your source equipment remote control in your second room please follow the advice below below: 1) Ensure the IR Emitter is connected to the socket labelled ‘IR’ on the Transmitter. 2) Ensure you are using the correct remote control in the second room.
DG458 - DigiSender® ZX7 - 5.8GHz Quad Input Wireless AV Sender Technical Support AEI Security & Communications Ltd is dedicated to providing our customers with first class customer care and technical support. During busy periods we would suggest using the web option to obtain support. 1. On the web... Free technical advice is available online 24/7 at our dedicated support web site: www.aei.eu 2. By telephone... We have a dedicated helpline, open Monday to Friday, 9AM - 5PM.
SPECIFICATIONS DG458 Transmitter : Remote Relay Receiver Audio/Video Frequency Modulation Video Input Level Colour Video Input Audio Input Level Audio Bandwidth Input Connectors Power Source DG458 Receiver : Remote Relay Transmitter Audio/Video Frequency Modulation Video Output Level Sensitivity Audio Output Level Audio Bandwidth Output Connectors Power Source 433.92MHz 5.7250GHz ~ 5.8750GHz FM 1V PP/75Ω Phase Alternate Line (PAL) 1.
