60109-1 xSender MODEL: DG180-S Wireless Video Sender System LR150-S PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERANCE
DG180-S - Wireless Video Sender System TABLE OF CONTENTS 1. Introduction 3 2. Unpack Your xSender™ 4 3. Install The xSender™ Transmitter 5 4. Install The xSender™ Receiver 7 5. Using the xSender™ 8 6. AV Channel Settings 9 7. Troubleshooting: Picture Problems 10 8. Troubleshooting: Audio Problems 12 9. Troubleshooting: Remote Relay Problems 13 10. Technical Support 14 11. Upgrades & Accessories 15 12.
DG180-S - Wireless Video Sender System INTRODUCTION Congratulations on purchasing the xSender™. This product represents state of the art wireless video technology and exceptional value for money. You can now enjoy crisp video and hi-fi stereo sound from your Satellite, Freeview, DVD or VCR in another room in your home. The xSender™ is designed to work with virtually any video source and is an ideal solution for transmitting channels from a typical home entertainment environment.
DG180-S - Wireless Video Sender System STEP 1 Unpack your xSender™ All packs are computer weigh checked when packed. However, it is a good idea to check all kit contents are present before proceeding with the installation.
DG180-S - Wireless Video Sender System STEP 2 Install the xSender™ Transmitter The DG180-S Transmitter will send the sound and video from a connected source (Satellite, Freeview, DVD, VCR, etc.) to the DG180-S Receiver, located in another room in your home. 1. 2. Insert the DigiConnector™ into the SCART socket labelled ‘TV’ or ‘OUT’ on your source equipment (Satellite, Freeview, DVD, VCR, etc.) and plug the SCART cable leading to your TV into the back of it.
DG180-S - Wireless Video Sender System continued... Important Note: Avoid positioning the DG180-S Transmitter near to other wireless devices operating on 2.4GHz. These can include Wireless Routers, Laptops, Games Consoles, DECT Phones or Bluetooth devices. 5. 6. Connect the Power Supply Unit (PSU) to the socket labelled ‘PSU’ on the DG180-S Transmitter. Connect the Power Supply Unit (PSU) to an available mains socket.
DG180-S - Wireless Video Sender System STEP 3 Install the xSender™ Receiver The xSender™ Receiver will pick up the signals being sent by your xSender™ Transmitter and output them to a connected TV. 1. 2. Locate a vacant SCART socket on the back of your receiving TV and insert the DigiSender® SCART cable. Ensure that the A/V Channel switch on the back of the DG180-S Receiver is set to 1. 3. 4. Connect the Power Supply Unit (PSU) to the socket labelled ‘PSU’ on the DG180-S Receiver.
DG180-S - Wireless Video Sender System STEP 4 Using the xSender™ 1. 2. Switch on the source equipment (Satellite, Freeview, DVD, VCR, etc.). Switch on the xSender™ Transmitter and Receiver at the rear of the units. 3. 4. On the receiving TV, select the SCART channel assigned to the SCART socket that you plugged the DG180-S Receiver in to. This may be labelled as SCART, AUX, AV, VIDEO, VCR or . To control your source equipment, use its original remote control i.e.
DG180-S - Wireless Video Sender System A/V Channel Settings The xSender™ features 4 Audio/Video Channels. Each of these A/V Channels changes the frequency on which the xSender™ operates and is useful for when other wireless devices are present in your home. Because the A/V Channel switch allows you to ‘fine tune’ the frequency on which your xSender™ operates, it is possible to overcome most interference and reception troubles that may occur.
DG180-S - Wireless Video Sender System TROUBLESHOOTING Picture Problems Q: What do you see on your second television? The picture is present but poor quality POOR RANGE 1. The picture & sound quality is affected by the transmitter and receiver’s location. Try positioning them in different locations. The transmitter and receiver must be connected to a mains extension lead that can be moved. 2.
DG180-S - Wireless Video Sender System cont... I see a snowstorm effect or plain blue screen Switch OFF your DigiSender® RECEIVER. Q: What do you now see at the second TV? I now see a Black screen I still see a snowstorm or blue picture NOT RECEIVING SIGNAL WRONG TV CHANNEL SELECTED 1. Switch the DigiSender® Receiver back on 2. Ensure the DigiSender® Transmitter is switched on 3. Select a different audio/video channel ensuring an identical channel is chosen on both the transmitter and receiver 4.
DG180-S - Wireless Video Sender System TROUBLESHOOTING Audio Problems I can see the picture but can’t hear anything. The sound is distorted. Q: What seems to be the problem with the sound? There is a buzzing sound present. It seems to get worse during on-screen menus or bright pictures. There is a hissing sound and the volume must be turned up high on the second TV to hear anything. Page 12 1. Disconnect both the transmitter AND receiver SCART’s.
DG180-S - Wireless Video Sender System TROUBLESHOOTING Problems Controlling the Source Equipment If you have any difficulty operating your source equipment remote control in your second room please follow the advice below below: 1) Ensure the IR Emitter is connected to the socket labelled ‘IR’ on the xSender™ Transmitter. 2) Ensure you are using the correct remote control in the second room.
DG180-S - Wireless Video Sender System Technical Support AEI Security & Communications Ltd is dedicated to providing our customers with first class customer care and technical support. We have provided you with 2 methods of obtaining technical advice on this product. During busy periods we would suggest using the web option to obtain support. 1. On the web... Free technical advice is available online 24/7 at our dedicated support web site: http://www.aei.eu 2. By telephone...
DG180-S - Wireless Video Sender System Upgrades & Accessories Additional Receiver - Part DG20RX Aerial Convertor - Part MOD01PIS • Get your Satellite channels to additional TV’s in your home! • Add as many Receivers as you require to your DigiSender® system • Connect to any SCART enabled TV or use with the MOD01PIS Aerial Converter • Supplied with Power Supply Unit • Requires DigiSender® Transmitter • Connect a DigiSender® Receiver to an aerial socket on your TV • Shares the power supply with your Digi
DG180-S - Wireless Video Sender System REAR PANEL DESCRIPTIONS xSender™ Transmitter 2 3 4 5 4. Power Supply Connect one of the supplied power Supply Adaptors here 1 1. Audio/Video Channel Default: Channel 1 See Advanced Section for details. 5. Power Switch (0/1) Used to switch ON and OFF your DigiSender transmitter. Please read this instruction manual carefully prior to installation Page 16 2. DigiConnector Connect your satellite or cable here. 3.
DG180-S - Wireless Video Sender System REAR PANEL DESCRIPTIONS xSender™ Receiver 1 1. Audio/Video Channel Default: Channel 1 See Advanced Section for details. 2 2. SCART Out Use this lead to connect to an available SCART input on your remote television. 3. Power Supply Connect one of the supplied power supply adaptors here. 3 4 4. Power Switch (0/1) Use this to switch your xSender™ receiver ON or OFF. Figure 7.
DG180-S - Wireless Video Sender System Notes Page 18 Please read this instruction manual carefully prior to installation
SPECIFICATIONS Transmitter : Remote Relay Receiver Audio/Video Frequency Channel Frequency Modulation Video Input Level Colour Video Input Audio Input Level Audio Bandwidth Input Connectors Power Source 433.92MHz 2.4000GHz ~ 2.4835GHz 2.414GHz - 2.468GHz FM 1V PP/75Ω Phase Alternate Line (PAL) 1.
