DG180-S xSender™ Wireless Video Sender System LR150-S IMPORTANT: ALWAYS KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
Table of contents 3 xSender™ Introduction 4 xSender™ Pack contents 5 New Features 6 Transmitter rear panel descriptions 7 Receiver rear panel descriptions 8,9 Connecting the transmitter 10,11 Finishing the transmitter installation 12,13 Connecting the receiver 14,15 Upgrade options 16,17 Frequently Asked Questions (FAQ) 18 Technical Support 19 Technical Specifications WARNING To prevent damage do not expose this unit to rain or moisture.
DG180-S xSender™ Introduction Congratulations on purchasing the xSender™. This product represents state of the art wireless video technology and exceptional value for money. You can now enjoy receiving crisp pictures and stereo sound from your satellite receiver or DVD player for example, located in another room.
xSender™ Pack Contents Magic Eye Transmitter Page 4 2 x Power Supply Receiver http://www.aei.
IMPORTANT Changing the Audio/Video (2.4GHz) Channel This section only applies if you are using more than 1 transmitter (for example, CCTV use) or a neighbour is also using a wireless video sender. There are 4 channels available for use in the 2.4GHz band. Your transmitter and receiver MUST be set to the same channel in order to operate. This setting is made on the rear of the units, look for the switch labelled ‘Audio/Video Channel’ PLEASE PROCEED TO PAGE 6 TO PROCEED WITH INSTALLATION OF THIS PRODUCT.
3 4 5 1. Audio/Video Channel Default: Channel 1 See Advanced Section for details. 4. Power Supply Connect one of the supplied power Supply Adaptors here 2. DigiConnector Connect your satellite or cable here. 5. Power Switch (0/1) Used to switch ON and OFF your DigiSender transmitter. http://www.aei.info Figure 6.1 xSender DG180-S Transmitter 2 3. Magic Eye Output Connect the supplied magic eye remote extender here.
Page 7 1. Audio/Video Channel Default: Channel 1 See Advanced Section for details. 3 4 Figure 7.1 xSender DG180-S Receiver 2 4. Power Switch (0/1) Use this to switch your xSender™ receiver ON or OFF. 2. SCART Out Use this lead to connect to an available SCART input on your remote television. 3. Power Supply Connect one of the supplied power supply adaptors here.
Connecting a SCART device to your xSender™ transmitter You can use the DigiConnector to connect a SCART device to your transmitter. This could be one of the following devices. STEP 1 Connect the DigiConnector to a SCART socket on your source equipment.This could be your Satellite/Cable Decoder, DVD player or VCR.
STEP 2 CONTRAST SETTING (A/B) If there was already a SCART lead connecting this item to your TV: connect it to the socket section on the DigiConnector. The contrast setting switch may be adjusted if the picture and sound on the receiving television is of a poor quality. NOTE: Don’t worry if you don’t already have a SCART lead to connect here - this feature is optional Use this setting if the picture and/or sound degrades when using on screen menus or text.
Finishing the transmitter installation You’ve almost finished installing the transmitter! The xSender™ features an internal remote control extender. This enables you to use your original equipment remote controls in the remote location. The ‘magic eye’ emits your original remote control signals and must be positioned correctly in order to work well. STEP 1 Connect one of the supplied PSU’s (power supply unit) to your xSender™ transmitter.
STEP 2 STEP 3 Connect the ‘magic eye’ lead to the xSender™ transmitter as shown below. The Magic eye emits its infra red signals from the tip, therefore you may find it works better fixed to a shelf facing the front of your equipment. (NOTE: Do not fix the magic eye into position until you have confirmed operation at your preferred choice). NTL® and Telewest® customers may require the DigiEye™ upgrade. See FAQ for details. Figure 11.1 Connecting the magic eye lead DG180-S xSender™ Figure 11.
Connecting the xSender™ receiver to your television Your xSender™ receiver can be connected to any remote television with a SCART socket. NO SCART SOCKET? You need the Aerial Convertor. Ask for part: STEP 1 Connect the SCART lead to an available SCART socket on your remote television. IMPORTANT: We recommend switching off your television set prior to connecting the SCART lead.
STEP 2 STEP 3 Connect the power supply unit as show below.Then, switch ON the xSender™ receiver and your television. You must select your televisions A/V channel in order to view your remote equipment (satellite/cable television etc.) This is done on your televisions remote control unit. We have made a list below of some of the more common buttons you need to press to activate the A/V channel.
Upgrade Options Receive your Satellite/Cable on additional televisions. Add up to 4 Wireless CCTV cameras to your system.
Connect your receiver to any TV - no SCART socket required! Part Number: MOD01PIS • Connect an xSender™ receiver to an aerial socket on your T.V. • Shares the power supply with your xSender™ • Test Card signal for easy set up • Compatible with every UK television • Adds the xSender™ signal to your existing aerial signal www.digisender.
Frequently asked questions (FAQ) Q: I can’t get my Digital Cable remote control to work! A: This model of xSender may be incompatible with your Digital Cable Receiver. i) Purchase the DigiEye Intelligent Remote Control Extender (part DG100DE) ii) Or, upgrade this system to the xSender Gold DG400 system. Q: I can only see a fuzzy ‘snowstorm’ picture! A: This could be caused by a number of reasons. Check out the following...
Q: There is interference on my picture! A: You need to change the Audio/Video channel of your xSender. See page 5 for details. Q: I can’t choose a different Satellite/Cable channel from my main room! A: This is normal. Your Satellite/Cable decoder can only decode one channel at a time. Q: My neighbour is changing my Satellite/Cable channel! A: Your neighbour is using a xSender system. Consider purchasing the DigiEye Intelligent remote control extender. This device features 16 remote channels.
Technical Support AEI Security & Communications Ltd is dedicated to providing our customers and end-users with first class technical support. To this end, we have provided you with 3 methods of obtaining technical advice on this product. During busy periods we would recommend using the web and e-mail bases options to obtain support. 1. On the web... Free technical advice is available online 24/7 at our dedicated support web site: http://www.digisender.net 2. By e-mail...
Technical Specifications Transmitter : Remote relay receiver Audio/Video Frequency Channel Frequency Modulation Video Input Level Colour Video Input Audio Input Level Audio Bandwidth Input Connectors Power Source 433.92MHz 2.4000GHz ~ 2.4835GHz Channel 1 2.414GHz Channel 2 2.432GHz Channel 3 2.450GHz Channel 4 2.468GHz FM 1V PP/75Ω Phase Alternate Line (PAL) 1.
(c)2007 AEI Security & Communications Ltd. All rights reserved.
