User's Manual

8
REFRESH THE SYSTEM WITH THE “DEFAULT CODE” --- 9 9 9 9
The system can be refreshed with the Default Code to clear all the old data.
DEFAULT CODE
The Default Code 9 9 9 9 is for setting the system back to default values. Once the default code is
entered and validated, all the old values will be cleared except the Master Code. Re-programming
of the features is necessary.
Make sure that you really want to clear the OLD values before entering the Default Code.
THE DEFAULT VALUES OF THE KEYPAD
PROGRAMMING
LOCATION PARAMETERS DEFAULT FUNCTIONS & VALUES
0 Master Code Not Affected *
1 User Codes for O/P 1 Nil ----- User Program Required
2 User Codes for O/P 2 Nil ----- User Program Required
3 User Codes for O/P 3 Nil ----- User Program Required
4 Super User Code Nil ----- User Program Required
5 Visitor Codes Nil ----- User Program Required
6 Personal Safety & Lock-out Code = 1, 10 False Code Lock-out 30 S
7 User Code Entry Mode Code = 1, Auto Entry Mode
8 Pacier Tones ON-OFF Selection Code = 1, Pacier Tone Partially ON
9 Back-lit ON-OFF Selection Code = 0, Back-lit OFF
NOTE:
i) The master code is NOT a default value. It is not affected in system refreshing.
ii) The DAP Code 8 0 8 0 and the Refreshing Code 9 9 9 9 are xed in the system program. It can not
be changed in any ways or be inuenced by the system in the default setting.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
9
DEFAULT CODE VALIDATION
9999 #
SET SYSTEM IN PROGRAMMING MODE OR REFRESH THE SYSTEM
SET SYSTEM INTO PROGRAMMING MODE WITH THE MASTER CODE
It is necessary to set the system into programming mode to accept the new programming values.
MASTER CODE
The Master Code can be a factory set master code or the private
master code set by the owner to replace the factory set master code.
Validate the master code with
* *
NOTE:
a)
b)
DIRECT ACCESS TO PROGRAMMING MODE WITH THE “DAP” CODE – 8 0 8 0
In case of the Master Code is forgotten. The owner requires to apply the following procedures
precisely to set the system into programming mode with the DAP code 8 0 8 0.
1)
2)
DAP CODE
The DAP code is xed at 8 0 8 0 .
The system will go back to normal operation after the power up period expired.To set it back to
power-up mode, repeat procedures (1) & (2) are required.
Validate the DAP code with the
* *
.
2-beep conrms the system is in Programming Mode. The amber LED ashes. The OLD Master
Code is cleared.
See “RECORD A MASTER CODE” for the details of programming a new master code.
For the owner’s convenience in programming for the rst time, a Master Code “0 0 0 0” has been
put in the keypad before exiting factory. To compromise security, in all cases, the owner should
program a personal Master Code to invalidate the factory set master code.
2-beep confirms that the master code is valid and the amber LED flashes during keypad in
Programming Mode.
Switch OFF all the power for 1 minute to ensure that the system is fully discharged. Press any
button will shorten the discharging time.
Switch ON power again. The system will be in Power-up Mode for 1 minute and the buzzer starts
to give beeps during the period. This is the only time that the system allows entry of the DAP code.
0000
8080


MASTER CODE VALIDATION
DAP CODE VALIDATION