Before continuing The Electricity Board’s regulations congesting connection must be strictly adhered to. Your oven must be installed by a quantified electrician. Please read these instructions carefully before Using your new appliance. This will enable you to make tilt use of al its faculties.
Features 3 Leavenworth 1 automatic cooking areas 5 controls for the automatic cooking areas Dded open fast cooking areas & controls for fhe fast cooking areas theorizing 3 warming area instructions! 4 autocratic Amer with digital clock, with automatic START and STOP and with a minute minder (on mode! S 64 0} Mode! § 64D
Before using for the first time automatic cooking area at the front | automatic cooking area at the rear digital cock controls for the automatic cooking areas Surface coating If you are installing your new AEG control Before using for the first time, set sate hot unit with a vitreous enameler or stainless steel plate in turn to a maximum heat setting for a hob unit (not Vitriolic hobs} iris necessary period of approximately 10 minutes.
The cooking areas — general ; s Siamese of gan Assisi oo small Di sorted pan base 35 al e large far plate han pie oot heat trans tar -~ longs cooking Erma considerate ss. of heat Eradicator se Yoo Gl GG DIPHTHONG oo remembered] foolery The correct spooking utensils Good quality utensils and pans with level bases require less energy and a lower sting.
The cooking areas — general Switch oft position bellow indicator lights (which show when the cooking areas are heating ug) autocratic cooking areas front left rear left tacit couching areas rear right Trent right The coaching areas referred to in the book cane dither solid hotplates on vitreous enamel o stainless steer gabs or cascara glass cooking areas on the VITRIOLIC hob. Your control pane! has controls for four cooking areas: two automatic cooking areas and two fast cooking areas.
Cooking and frying on the automatic cooking areas The following instructions wife ell you how you should Lse the automatic caking areas for cooking, stewing end billing without the fad boiling over and burning, The cooking area wil automatically keep (o the selected setting and switch from biffing or heating up to simmering automatically. The adjoining chart domains a few examples. of switch settings you may use. To switch on with automatic cooking Place the pan o the cooking area.
Cooking and frying on the automatic cooking areas important; The switch settings in this table refits fo quantities for four persons and to the use of the correct pan, The values should only be regarded as a guide since the food varies as to quantity and quality.
Cooking and frying on the fast cooking areas Fast cooking areas have a higher connected load than standard cooking areas. After bringing food to the boil, o after tha initial heating up period the fast cooking areas must be switched to simmering The following chart can be used as a guide for the suitable settings. Sat the switch to § and alter initial heating up return | 1o & lower sting for the remaining mocking time.
Using the warming area on the VITRIOLIC hob M Warming area Central light far warming ares i Sliding switch for Warming area | The waning area can only be used for heating up crockery and for keeping food warm, The warming area is operated with the sliding switch which Is located in the splash back at the rear right side of the VITRIOLIC hob (see illustration. Warming area Switching on. Move the switch to the left: the symbol [ appears and the control light will come on. Switching off.
Using the automatic timer automatic cooking area at the front | automatic cooking area af the rear 1 digit clock and automatic 24 hour timer controls for automatic cooking ares These Your control panel features a digital ® o clock showing the exact time of day, instructions clock with an automatic 24 hour timer, and el crunchiness B minute minder with an alarm R anatomic START, as well as on o remind you of the end of a selected automatic START and TOP, cooking time.
Digital timer with minute minder 13 Dial clock The AEG timer in your contort panel wil always show you the correct time of day. 11 is called a digital clock, because R shows the time in digits and not by the conventional method of hands, Setting the clock When the appliance has just been connected, or after a power out, proceed as follows; 1. Pull out knob () — the digits wil restate in & spaded up fashion. 2.
Automatic STOP and START/STOP Automatic SOFT and START/STOP tacitness are & feature of this control panel which can be used for the two automatic Rooking areas sinner individually o together at the same time. At the end of the cooking time you will hear a buzzer which switches oft automatically tater & few minutes Setting the ‘automatic STOP ¥ the green ding on the starting dial (9 is ot visible, turn the change-over button @10 (and press uni the starting dial stops.
Cleaning and maintenance 15 Gene rat Always let the cooking surfaces cool down Never use abrasive cleaners of Scouring before cleaning. powders; bleach and stain removers. Turnover food residues with a dare Never place aluminum FOFL over the cloth and washing up liquid. cooking areas, VITRIOLIC-hobe Ceramic surfaces require regular care and 3. Clean ine VITRIOLIC hat thoroughly {ceramic glass nobs) cleaning. Please follow the suggestions Bated below: 1.
Paints to preserver when installing and connecting 17 This appliance compiles with the requirements fad out in the ECG Dir active 76/889. See also Installation instructions for build-in control panels! Fa This s & job for & qualified and approved electrician. The appliance is rated for 240 volts single phase AC and must be permanently connected. All instructions given by the Electricity Board must be followed carefully when consenting the oven 1o the main supply.
What to coif . .. (something goes wrong) What can be Nor i-tunctioning of your control panel is the cause mostly due 1o minor causes which you it can rectify yourself. the Neck whether the operating sequence control has been fully carried out, lights donor Check whether the fuses in the work? fuse box are in good working order. Check that the change-over bunion is sett 4 and that he start fme is the same as on the clock.
What (something goes wrong) 19 | W Please transfer the details on the raking plate to the space provided below Model E no. Serial no. (No) important Please make sure that you are ot able o rectify the fault yourself priority calling 2 service engine at in connection with ong of the aforementioned problems, as the cost involved wilt have to be passed nonsense during the warranty period: Therefore. follow the instructions and recommendations in this bookie carefully.
