FFE83800PM USER MANUAL EN User Manual Dishwasher
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 2 2. SAFETY INSTRUCTIONS.............................................................................................4 3. PRODUCT DESCRIPTION...........................................................................................6 4. CONTROL PANEL....................................................................................................... 7 5. PROGRAMMES...
ENGLISH 3 damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • • Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket. Do not use high pressure water sprays and/or steam to clean the appliance. The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused. The ventilation openings in the base (if applicable) must not be obstructed by a carpet. Some dishwasher detergents are strongly alkaline.
ENGLISH new devices fitted (water meters, etc.), let the water flow until it is clean and clear. • Ensure that there are no visible water leaks during and after the first use of the appliance. • The water inlet hose has a safety valve and a sheath with an inner mains cable. 5 • Do not put flammable products or items that are wet with flammable products in, near or on the appliance. 2.5 Internal light WARNING! Risk of injury.
www.aeg.com 3. PRODUCT DESCRIPTION 1 2 3 12 11 10 9 8 7 1 2 3 4 5 6 7 6 Top spray arm Upper spray arm Lower spray arm Filters Rating plate Air vent Rinse aid dispenser 3.1 TimeBeam The TimeBeam is a display that is shown on the floor below the appliance door. • When the programme starts, the programme duration comes on. • When the programme is completed, 0:00 and CLEAN come on. • When the delay start starts, the countdown duration and DELAY come on.
ENGLISH When AirDry is activated during the drying phase, the projection on the floor may not be completely visible. To check the remaining time of the running programme, look at the control panel display. 4. CONTROL PANEL 2 1 1 2 3 4 5 On/off button Display Program touchpad Delay touchpad MyFavourite touchpad 4 3 6 7 8 9 5 6 7 8 TimeSaver touchpad XtraDry touchpad ExtraHygiene touchpad Indicators 5.
www.aeg.
ENGLISH Programme 1) Water (l) Energy (kWh) Duration (min) P5 14 - 16 1.2 - 1.5 160 - 180 P3 12.5 - 14.5 1.4 - 1.7 170 - 190 P6 12 - 14 0.7 - 0.9 82 - 92 P4 10.5 0.7 38 P8 4 0.01 14 P7 9.0 - 10.0 1.1 - 1.3 230 - 250 9 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 5.
www.aeg.com To enter user mode, press and hold simultaneously and until the indicators , , , and and the display is blank. flash Factory setting: level 4. 6.2 The rinse aid empty notification The rinse aid helps to dry the dishes without streaks and stains. The rinse aid is automatically released during the hot rinse phase. When rinse aid chamber is empty, the rinse aid indicator is turned on notifying to refill rinse aid.
ENGLISH 3. Press the on/off button to confirm the setting. 6.5 How to set the colour of the TimeBeam The appliance must be in programme selection mode. It is possible to change the colour of the TimeBeam to match the colour of the kitchen floor. There are several colours available. The TimeBeam can also be deactivated. Make sure the appliance is in user mode. 1. Press , , and still flashes. • The indicator • The display shows a number and letter C. Each number refers to a different colour.
www.aeg.com How to set the MyFavourite programme • If options are saved together with the programme, the indicators related to the options are on. . Press • The MyFavourite indicator is on. • The display shows the number and the duration of the programme. 7. OPTIONS Desired options must be activated every time before you start a programme. It is not possible to activate or deactivate options while a programme is running. Not all options are compatible with each other.
ENGLISH °C for at least 10 minutes during the last rinsing phase. How to activate ExtraHygiene Press , the related indicator comes on 13 If the option is not applicable to the programme, the related indicator does not come on or it flashes quickly for a few seconds and then goes out. The display shows the updated programme duration. 8. BEFORE FIRST USE 1. Fill the rinse aid dispenser. 2. Open the water tap. 3. Start a program to remove any processing residuals that can still be inside the appliance.
www.aeg.com 9.1 Comfort Lift CAUTION! Do not sit on the rack. Do not put excessive pressure on the locked basket. CAUTION! Do not exceed the max load capacity of 18 kg. CAUTION! Use only a detergent specifically designed for dishwashers. To ensure correct unlocking, lift the release handle completely and the basket slightly until the basket is disengaged on both sides.
ENGLISH 15 9.3 Setting and starting a programme When the countdown is completed, the programme starts. The Auto Off function Opening the door while the appliance operates This function decreases energy consumption by deactivating automatically the appliance when it is not operating. The function comes into operation: • 5 minutes after the completion of the programme. • After 5 minutes if the programme has not started. Starting a programme 1. Keep the appliance door ajar. 2.
www.aeg.com End of programme Close the water tap. When the programme is completed and you open the door, the appliance is automatically deactivated. 10. HINTS AND TIPS 10.1 General 10.3 Loading the baskets The following hints will ensure optimal cleaning and drying results in daily use and also help to protect the environment. • Only use the appliance to wash items that are dishwasher-safe. • Do not put in the appliance items made of wood, horn, aluminium, pewter and copper.
ENGLISH 10.5 Unloading the baskets 1. For improved drying results with the most efficient use of energy select the AirDry option, otherwise open the door by approximately 10cm at the end of the program. 2. Allow the tableware to cool for 30 40 minutes. 3. Hot items can be easily damaged, allow them to cool down before removing from appliance. 17 4. First remove items from the lower basket then the upper basket.
www.aeg.com 11.2 Cleaning the upper spray arm We recommend to clean regularly the upper spray arm to avoid soil to clog the holes. Clogged holes can cause unsatisfactory washing results. 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 1. Pull out the upper basket. 2.
ENGLISH 11.3 External cleaning • Clean the appliance with a moist soft cloth. • Only use neutral detergents. • Do not use abrasive products, abrasive cleaning pads or solvents. 19 • Do not use abrasive products, abrasive cleaning pads, sharp tools, strong chemicals, scourer or solvents. • If you use short duration programmes regularly, these can leave deposits of grease and limescale inside the appliance. To prevent this, we recommend running long duration programmes at least twice a month.
www.aeg.com Problem and alarm code Possible solution The appliance does not fill with water. • Make sure that the water tap is open. • Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. • Make sure that the water tap is not clogged. • Make sure that the filter in the inlet hose is not clogged. • Make sure that the inlet hose has no kinks or bends. The display shows or . The appliance does not drain the water.
ENGLISH Refer to "Before first use", "Daily use", or "Hints and tips" for other possible causes. Once you have checked the appliance, deactivate and activate the appliance. If 21 the problem occurs again, contact an Authorised Service Centre. For alarm codes not described in the table, contact an Authorised Service Centre. 12.1 The washing and drying results are not satisfactory Problem Possible cause and solution Poor washing results.
www.aeg.com Problem Possible cause and solution Traces of rust on cutlery. • Silver and stainless steel cutlery were placed together. Avoid to put silver and stainless steel items close together. There are residues of detergent in the dispenser at the end of the programme. • The detergent tablet got stuck in the dispenser and therefore was not completely washed away by water. • Water cannot wash away the detergent from the dispenser. Make sure that the spray arm is not blocked or clogged.
ENGLISH 23 14. INSTALLATION There should be a minimum 2mm gap between the top of the dishwasher and underside of bench top Remove entire plastic membrane from sink trap spigot & fit drain hose to spigot with clamp The hose should not be extended by more than 2 metres or water pumpout problems may occur SINK Secure dishwasher with brackets or screws provided DISHWASHER Gap on both sides should be equal, & no greater than 5 mm per side.
www.aeg.com The water pressure must be in the limits indicated in the chapter ''TECHNICAL INFORMATION''. Make sure that the local water authority gives you the average mains pressure in your area. In order to pass the safety valve through the kitchen cabinets, an opening of at least 45 mm x 90 mm is needed. Parts. The extension length must not exceed 2 metres. The drain hose must be free of obstructions.
ENGLISH 2. 3. 4. 5.
www.aeg.com 9. To the extent permitted by law and subject to your non-excludable statutory rights and warranties, AEG excludes all warranties and liabilities (other than as contained in this document) including liability for any loss or damage whether direct or indirect arising from your purchase, use or non use of the Appliance. 10. For AEG Appliances and services in Australia, the Appliances come with a guarantee that cannot be excluded under the ACL.
ENGLISH 27 FOR SERVICE or to find the address of your nearest authorised service centre in New Zealand FREE CALL 0800 10 66 10 OR EMAIL customercare@electrolux.co.nz (New Zealand only) FOR SPARE PARTS or to find the address of your nearest state spare parts centre in New Zealand FREE CALL 0800 10 66 20 OR EMAIL customercare@electrolux.co.nz (New Zealand only) 16. ENVIRONMENTAL CONCERNS Recycle materials with the symbol . Put the packaging in relevant containers to recycle it.
117881890-A-172017 www.aeg.
