FFE62800PM USER MANUAL EN User Manual Dishwasher
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 2 2. SAFETY INSTRUCTIONS.............................................................................................4 3. PRODUCT DESCRIPTION...........................................................................................6 4. CONTROL PANEL....................................................................................................... 7 5. PROGRAMMES...
ENGLISH 3 manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • • • If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. Put the cutlery in the cutlery basket with the sharp ends pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down. Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it.
ENGLISH • Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. • This appliance complies with the E.E.C. Directives. • UK and Ireland only. This appliance is fitted with a 13 A mains plug. If it is necessary to change the mains plug fuse, use only a 13 A ASTA (BS 1362) fuse. 2.3 Water connection • Do not cause damage to the water hoses.
www.aeg.com 3. PRODUCT DESCRIPTION 1 2 3 14 13 12 11 10 9 8 1 2 3 4 5 6 7 8 7 6 Top spray arm Upper spray arm Lower spray arm Filters Rating plate Salt container Air vent Rinse aid dispenser 3.1 Beam-on-Floor The Beam-on-Floor is a light that is displayed on the floor below the appliance door. • When the programme starts, a red light comes on and stays on for the duration of the programme. • When the programme is completed, a green light comes on.
ENGLISH 4. CONTROL PANEL 2 1 1 2 3 4 5 On/off button Display Program button Delay button MyFavourite button 3 6 7 8 9 4 5 6 7 8 9 TimeSaver button XtraDry button ExtraHygiene button Indicators 4.1 Indicators Indicator Description Rinse aid indicator. It is always off while the programme operates. Salt indicator. It is always off while the programme operates. 5. PROGRAMMES The numbering of the programmes in the table (P1, P2, etc.) reflects their sequence on the control panel.
www.aeg.
ENGLISH 9 5.1 Consumption values Water (l) Energy (kWh) Duration (min) P1 11 0.921 235 P2 8 - 15 0.7 - 1.7 46 - 170 P5 14 - 16 1.2 - 1.5 160 - 180 P3 12.5 - 14.5 1.4 - 1.7 170 - 190 P6 12 - 14 0.8 - 1.0 82 - 92 P4 10 0.9 30 P8 4 0.1 14 P7 12 - 13 1.1 - 1.3 230 - 250 Programme 1) 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 5.
www.aeg.com How to set the programme selection mode indicators , , , and and the display is blank. The appliance is in programme selection mode when the display shows the programme number P1. 6.2 The water softener After activation, the appliance is in programme selection mode by default. If not, set the programme selection mode the following way: Press and hold simultaneously and until the appliance is in programme selection mode.
ENGLISH • The indicators are off. , , and • The indicator still flashes. • The display shows the current setting: e.g. = level 5. repeatedly to change the 2. Press setting. 3. Press the on/off button to confirm the setting. 6.3 The rinse aid empty notification The rinse aid helps to dry the dishes without streaks and stains. It is automatically released during the hot rinse phase. When the rinse aid chamber is empty, the rinse aid indicator is turned on notifying to refill rinse aid.
www.aeg.com 6.6 AirDry How to deactivate AirDry AirDry improves the drying results with less energy consumption. Make sure the appliance is in user mode. 1. Press . • The indicators are off. , , and • The indicator still flashes. • The display shows the current setting. – = AirDry is deactivated. – = AirDry is activated. 2. Press to change the setting. 3. Press on/off to confirm the setting. 6.7 MyFavourite During the drying phase, the door opens automatically and remains ajar.
ENGLISH Not all options are compatible with each other. If you select non compatible options, the appliance automatically deactivates one or more of them. Only the indicators of the still active options are on. If an option is not applicable to a programme, the related indicator is off or it flashes quickly for a few seconds and then goes out. Activating options can affect the water and energy consumption as well as the programme duration. 7.
www.aeg.com 4. Open the water tap. 5. Start a programme to remove any processing residuals that can still be inside the appliance. Do not use detergent and do not load the baskets. After starting a programme, it may take up to 5 minutes for the appliance to recharge the resin in the water softener. It seems that the appliance is not working. The washing phase starts only after this procedure is completed. The procedure is repeated periodically. 8.
ENGLISH 15 Fill the rinse aid dispenser when the indicator (A) is clear. 9. DAILY USE 1. Open the water tap. 2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. • If the salt indicator is on, fill the salt container. • If the rinse aid indicator is on, fill the rinse aid dispenser. 3. Load the baskets. 4. Add the detergent. 5. Set and start a programme suitable for the type of load and the degree of soil. 9.
www.aeg.com 9.2 Using the detergent A B 5. Close the appliance door to start the programme. Starting a programme with delay start 1. Set a programme. C CAUTION! Only use detergent specifically designed for dishwashers. 1. Press the release button (A) to open the lid (C). 2. Put the detergent, in powder or tablets, in the compartment (B). 3. If the programme has a prewash phase, put a small quantity of detergent on the inner part of the appliance door. 4. Close the lid.
ENGLISH Make sure that there is detergent in the detergent dispenser before you start a new programme. End of the programme When the programme is completed the display shows 0:00. All buttons are inactive except for the on/off button. 1. Press the on/off button or wait for the Auto Off function to automatically deactivate the appliance. If you open the door before the activation of Auto Off, the appliance is automatically deactivated. 17 2. Close the water tap.
www.aeg.com 4. When the programme is completed, adjust the water softener according to the water hardness in your area. 5. Adjust the released quantity of rinse aid. 6. Activate the rinse aid empty notification. 10.4 Loading the baskets • Use the appliance to wash dishwasher-safe items only. • Do not wash in the appliance items made of wood, horn, aluminium, pewter and copper. • Do not wash in the appliance items that can absorb water (sponges, household cloths).
ENGLISH 19 1. Turn the filter (B) counterclockwise and remove it. 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. 2. Remove the filter (C) out of filter (B). 3. Remove the flat filter (A). 4. Wash the filters. CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 11.
www.aeg.com 11.3 External cleaning • Clean the appliance with a moist soft cloth. • Only use neutral detergents. • Do not use abrasive products, abrasive cleaning pads or solvents. 11.4 Internal cleaning 3. Wash the spray arm under running water. Use a thin pointed tool, e.g. a toothpick, to remove particles of soil from the holes. 4. To install the spray arm back, press the spray arm upwards and simultaneously turn it counterclockwise until it locks into place.
ENGLISH 21 12. TROUBLESHOOTING WARNING! Improper repair of the appliance may pose a danger to the safety of the user. Any repairs must be performed by qualified personnel. to contact an Authorised Service Centre. Refer to the below table for information on possible problems. With some problems, the display shows an alarm code. The majority of problems that may occur can be solved without the need Problem and alarm code Possible cause and solution You cannot activate the appliance.
www.aeg.com Problem and alarm code Possible cause and solution The programme lasts too long. • If the delay start option is set, cancel the delay setting or wait for the end of the countdown. • Activate the TimeSaver option to reduce the programme duration. • Activating options can increase the programme duration. The remaining time in the display increases and skips nearly to the end of the programme duration. • This is not a defect. The appliance is working correctly.
ENGLISH 23 Problem Possible cause and solution Poor drying results. • Tableware has been left for too long inside the closed appliance. • There is no rinse aid or the dosage of rinse aid is not sufficient. Adjust the rinse aid level to a higher level. • Plastic items may need to be towel dried. • For the best drying performance, activate XtraDry and AirDry. • We recommend to always use rinse aid, even in combination with multi-tablets. There are whitish streaks or bluish layers on glasses and dishes.
www.aeg.com Problem Possible cause and solution Limescale deposits on the tableware, on the tub and on the inside of the door. • • • • Dull, discoloured or chipped tableware. • Make sure that only dishwasher-safe items are washed in the appliance. • Load and unload the basket carefully. Refer to basket loading leaflet. • Place delicate items in the upper basket. • For washing delicate items and glassware, select the dedicated programme. Refer to "Programmes". The level of salt is low.
ENGLISH 25 14. ENVIRONMENTAL CONCERNS Recycle materials with the symbol . Put the packaging in relevant containers to recycle it. Help protect the environment and human health by recycling waste of electrical and electronic appliances. Do not dispose of appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.
X X X Softener & inner components Hydraulic circuit (including tanks)* Wiring harnesses * Hg Cd Cr6+ Hazardous substances PBBs PBDEs Note: 1. This table is compiled according to SJ/T11364-2014. means that this kind of hazardous substance content in all of the homogenous materials of this part is under the limitations 2. regulated in GB/T26572-2011. 3.
ENGLISH 27
117876252-A-122018 www.aeg.
