User manual
Table Of Contents
- СЪДЪРЖАНИЕ
- 1. ИНФОРМАЦИЯ ЗА СИГУРНОСТ
- 2. ИНСТРУКЦИИ ЗА СИГУРНОСТ
- 3. ОПИСАНИЕ НА УРЕДА
- 4. KОМАНДНО ТАБЛО
- 5. ПРОГРАМИ
- 6. НАСТРОЙКИ
- 7. OПЦИИ
- 8. ПРЕДИ ПЪРВАТА УПОТРЕБА
- 9. ВСЕКИДНЕВНА УПОТРЕБА
- 10. ПРЕПОРЪКИ И СЪВЕТИ
- 11. ГРИЖИ И ПОЧИСТВАНЕ
- 12. ОТСТРАНЯВАНЕ НА НЕИЗПРАВНОСТИ
- 13. ТЕХНИЧЕСКА ИНФОРМАЦИЯ
- CONTENTS
- 1. SAFETY INFORMATION
- 2. SAFETY INSTRUCTIONS
- 3. PRODUCT DESCRIPTION
- 4. CONTROL PANEL
- 5. PROGRAMMES
- 6. SETTINGS
- 7. OPTIONS
- 8. BEFORE FIRST USE
- 9. DAILY USE
- 10. HINTS AND TIPS
- 11. CARE AND CLEANING
- 12. TROUBLESHOOTING
- 13. TECHNICAL INFORMATION
- TARTALOM
- 1. BIZTONSÁGI INFORMÁCIÓK
- 2. BIZTONSÁGI UTASÍTÁSOK
- 3. TERMÉKLEÍRÁS
- 4. KEZELŐPANEL
- 5. PROGRAMOK
- 6. BEÁLLÍTÁSOK
- 7. KIEGÉSZÍTŐ FUNKCIÓK
- 8. AZ ELSŐ HASZNÁLAT ELŐTT
- 9. NAPI HASZNÁLAT
- 10. HASZNOS TANÁCSOK ÉS JAVASLATOK
- 11. ÁPOLÁS ÉS TISZTÍTÁS
- 12. HIBAELHÁRÍTÁS
- 13. MŰSZAKI INFORMÁCIÓK

12.1 The washing and drying results are not satisfactory
Problem Possible cause and solution
Poor washing results. • Refer to "Daily use", "Hints and tips" and basket
loading leaflet.
• Use more intensive washing programmes.
• Clean spray arm jets and filter. Refer to "Care and
Cleaning".
Poor drying results. • Tableware has been left for too long inside a closed
appliance.
• There is no rinse aid or the dosage of rinse aid is not
enough. Set the rinse aid dispenser to a higher level.
• Plastic items may need to be towel dried.
• For the best drying performance activate the option
XtraDry.
• We recommend to always use rinse aid, even in com-
bination with multi-tablets.
There are whitish streaks or
bluish layers on glasses and
dishes.
• The release quantity of rinse aid is too much. Adjust
the rinse aid level to a lower level.
• The quantity of detergent is too much.
There are stains and dry water
drops on glasses and dishes.
• The released quantity of rinse aid is not sufficient. Ad-
just the rinse aid level to a higher level.
• The quality of the rinse aid can be the cause.
The dishes are wet. • For the best drying performance activate the option
XtraDry.
• The programme does not have a drying phase or has
a drying phase with low temperature.
• The rinse aid dispenser is empty.
• The quality of the rinse aid can be the cause.
• The quality of the multi-tablets can be the cause. Try a
different brand or activate the rinse aid dispenser and
use rinse aid and multi-tablets together.
• Keep the dishwasher door ajar for some time before
removing tableware.
The interior of the appliance is
wet.
• This is not a defect of the appliance. it is caused by
the humidity in the air that condenses on the walls.
Unusual foam during washing. • Use the detergent for dishwashers only.
• There is a leak in the rinse aid dispenser. Contact an
Authorised Service Centre.
Traces of rust on cutlery. • There is too much salt in the water used for washing.
Refer to "The water softener".
• Silver and stainless steel cutlery were placed together.
Avoid to put silver and stainless steel items close to-
gether.
www.aeg.com42










