FAVORIT 44080 i Dishwasher User information
Dear Customer, Please read this user information carefully and keep it to refer to later. Please pass the user information on to any future owner of the appliance. 1 3 2 2 The following symbols are used in the text: Safety instructions Warning! Information that affects your personal safety. Important! Information that prevents damage to the appliance.
Contents Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Diagram of Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Prior to Using for the First Time. . . . . . . .
Operating Instructions 1 Safety Prior to using for the first time • Follow the ”Instructions for installation and connection”. Correct Use • The dishwasher is only intended for washing domestic dishes. • Additions or modifications to the dishwasher are not permitted. • Use only special salt, detergent and rinse aid suitable for domestic dishwashers. • Do not put any solvents in the dishwasher. This could cause an explosion. Child Safety • Keep packaging away from children. There is a risk of suffocation.
Diagram of Appliance Top Spray Nozzle Upper basket spray arm and lower spray arm Water softener unit. Salt Container Detergent Dispenser Rinse aid dispenser Rating plate Filters Control Panel ON/OFF button The ON/OFF button is used to turn the dishwasher on and off.
Programme buttons End of cycle indicator Programme progress display 1 2 3 Set delay timer Function buttons Select 3 in1 function Control indicators The Programme buttons are used to select the desired dishwashing cycle.
Prior to Using for the First Time 3 If you wish to use 3 in 1 detergent: – First read the section “Using 3in1 detergents”. – Do not fill up with special salt or rinse aid. If you do not use 3in1 detergent, before using for the first time 1. Set the water softener 2. Fill up with dishwasher salt 3.
3. Press function button 1. The LED indicator for function button 1 will flash. The LED indicator for the end of the dishwashing cycle will flash simultaneously: – The number of times that the LED indicator for the end of the dishwashing cycle flashes corresponds to the hardness setting. – This sequence of flashes is repeated several times, with a 3 second pause in-between. 4. Pressing function button 1 increases the hardness setting by 1 degree. (Exception: hardness setting 1 follows hardness setting 10).
Adding dishwasher Salt 3 3 To decalcify the water softener, it must be filled up with dishwasher salt. Use only special salt suitable for domestic dishwashers. If you do not use 3 in1 detergent, fill up with dishwasher salt: – Before using the dishwasher for the first time. – When the control indicator for dishwasher salt is illuminated on the control panel. 1. Open the door and remove the lower basket. 2. Unscrew the lid on the salt dispenser by turning it anti-clockwise. 3.
Filling Up with Rinse Aid Rinse aid causes the rinse water to flow easily from the crockery leaving gleaming dishes and glassware. If you do not use 3in1 detergent, fill up with rinse aid: – Before using the dishwasher for the first time. – When the control indicator for rinse aid is illuminated on the control panel. Use only special rinse aid for dishwashers. 1. Open the door. The rinse aid compartment is located on the inside of the dishwasher door. 2.
Setting the Amount of Rinse Aid Required 3 Only change the amount dispensed, if smears, milky spots (reduce the amount) or dried on water spots (increase the amount) can be seen on glasses and dishes. (See section “If dishwashing results are not satisfactory”.) The dosage can be set from 1-6. The dosage is pre-set to “4” in the factory. 1. Open the dishwasher door. 2. Press the release button on the rinse aid compartment. 3. Open the cover. 4. Set the dosage level. 5.
In daily use Loading cutlery and dishes 1 Sponges, cleaning cloths and any other objects that can absorb water must not be washed in the dishwasher. Plastic and Teflon-coated dishes and pans tend to retain water droplets. These dishes and pans therefore do not dry as well as those made of china and stainless steel.
Loading cutlery 1 Warning: Sharp knives and other items of cutlery with sharp edges must be laid in the cutlery rack or in the upper basket to avoid the risk of injury. To ensure that all items of cutlery in the cutlery basket can be reached by the water, you should: 1.Place the grid insert on the cut- 2.Place forks and spoons in the lery basket cutlery basket's grid insert with their handles pointing downwards. For larger utensils, such as whisks, leave off one half of the cutlery grid.
To make it easier to load larger dishes, the two plate racks on the right in the lower basket can be folded down. Cups, Glasses, Coffee Service Load smaller, fragile crockery and long, sharp cutlery in the upper basket. • Arrange items of crockery on and under the folding cup racks so that they are offset from each other and water can reach all items. • The cup racks can be folded up out of the way for tall crockery items. • Lay or hang wine and brandy glasses in the slots in the cup racks.
Adjusting the Height of the Upper Basket Maximum height of dishes in the 3 Upper basket Lower basket with upper basket raised 22 cm 30 cm with upper basket lowered 24 cm 29 cm The height of the baskets can also be adjusted when they are loaded. Raising / Lowering the upper basket 1. Pull out the upper basket completely. 2. Holding the upper basket by the handle, raise it as far as it will go and then lower it vertically. The upper basket will latch into the lower or the upper position.
3 2. Place the detergent in the detergent dispenser. The markings indicate the dosing levels for powder detergents: “20/30” corresponds to approx. 20/30 ml of detergent. Follow the manufacturer’s instructions with regard to dosing and storage. 3. Close the lid and press until it locks into place. In the case of very heavily soiled dishes, fill the adjoining compartment (1) with additional detergent. This detergent comes into use during the pre-wash cycle.
Using 3in1 detergents 3 3 These products are detergents with a combined cleaning, rinsing and salt function. When the 3in1 function is activated, – the addition of special salt and rinse aid from the respective dispenser is prevented. – If the salt and rinse aid dispensers are empty, this is not indicated. – The dishwashing cycles can be up to 30 minutes longer. If you want to use 3in1 detergents, check whether these detergents are suitable for your water hardness.
Selecting the dishwashing cycle (Cycle Table) 22 - 24 Water (litres) • • • • • 9 0,8 30 12 - 24 • 14 - 16 Energy (kWh) • 1,00 - 1,50 - 90 - 110 • 1,80 - 2,00 • Dinner service and cookware, normally soiled temperature-sensitive crockery - 0,95 - 1,05 • Length (minutes) heavily soiled, dried-on food remains, in particular protein and starch Dinner service and cookware • 120 - 130 • • 130 - 160 - Drying Dishes, excluding just used, lightly to saucepans normally soiled Final
Selecting a programme When your dishes look like this, select: an intensive programme. a normal or energy-saving programme. a short programme (e.g. 30 minute programme).
Starting a Dishwashing Cycle 1. Check that the spray arms can turn freely. 2. Turn the water tap on fully. 3. Close the door. 4. Press the ON/OFF button. 5. Select the desired cycle. The programme display lights up. The selected cycle will begin after approximately 3 seconds. Interrupting or Cancelling a dishwashing cycle Interrupt a dishwashing cycle that is in progress if it is absolutely necessary.
3. Select dishwashing cycle. The LED indicator for the programme selected and the indicator next to the number of hours will light up. The dishwashing cycle will start automatically following a countdown of the hours set. To change the time delay: As long as the cycle has not yet started, you can still change the setting by pressing the DELAY TIMER button. Cancelling the delay timer: Press the DELAY TIMER button repeatedly until none of the three time displays is lit.
Care and cleaning 1 Do not use furniture care products or aggressive cleaners. • When necessary, clean the dishwasher’s controls with a soft cloth. • Occasionally check the internal dispensers, door seal and water inlet filter (if fitted) for dirt and clean them, if necessary. Cleaning the filters 3 The filters must be regularly checked and cleaned. Dirty filters will spoil the wash results. 1. Open the door and remove the lower basket. 2.
5. Remove the flat filter (3) from the base of the washing compartment and clean both surfaces thoroughly. 6. Re-insert the flat filter. 7. Place the fine filter in the micro-filter and fit the two together. 8. Insert the filter system in place and lock it by turning the handle clockwise as far as it will go. Ensure that the flat filter does not protrude above the base of the washing compartment. 1 Under no circumstances may the dishwasher be used without its filters.
3. Place cleaned upper basket spray arm back in position against the connecting piece: press the two together firmly, until you feel them snap into place. Bottom spray arm 1. To remove bottom spray arm, pull it upwards out of its catch. 2. Clean spray arm jets. 3. Place bottom spray arm back in position against connecting piece and press down firmly, until you feel it snap into place.
What to do if... Remedying small malfunctions If while the appliance is operating indicators on the control panel flash or are lit up as described in the following table, please consult this to find out how to remedy the fault. After remedying the fault that is flashing in the first or second rhythm in the programme progress display, press the button for the dishwashing cycle that had already started. The cycle will continue. In the case of other fault messages: – Cancel the dishwashing cycle.
Malfunction Possible cause the indicator for the end of the dishwashing cycle is The anti-flood system has flashing in sequence 3 short been triggered. light signals one after another. The mains plug is not plugged in. The cycle is not starting. Remedy Turn off the tap and contact the Service Force Centre. Plug in mains plug. A fuse in the house’s wiring Replace fuse. system is defective.
If the Dishwashing Results are not Satisfactory The dishes are still dirty. • The wrong dishwashing cycle was selected. • The dishes were loaded is such a way that the dishwashing water did not reach all items. The baskets for the dishes must not be overloaded. • The filters in the base of the washing compartment are dirty or incorrectly positioned. • Good quality detergent was not used, or too little was used.
Disposal 2 Packaging material The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<, >PS<, etc. Please dispose of the packaging materials in the appropriate container at your local waste disposal facilities. 2 Old appliance W 1 28 on the product or on its packaging indicates that this The symbol product may not be treated as household waste.
Technical Data Capacity: 12 place settings including serving dishes Permitted water pressure: 1-10 bar (=10-100 N/cm2 = 0.1-1.0 MPa) Electrical connection: 230 V, 13 A, also see the rating plate on the right-hand side of the dishwasher’s interior door . Total output 2250 W Dishwashers that can be integrated and built-in 5 Dimensions: 820 - 880 x 596 x 570 (H x W x D in mm) Max. weight: 50 kg This appliance conforms with the following EU Directives: – 73/23/EEC dated 19.02.
Notes for Test Institutes Testing in accordance with EN 60704 must be carried out with the appliance fully loaded and using the test cycle (see “Cycle Table”). Tests in accordance with EN 50242 must be carried out when the salt dispenser in the water softener and the rinse aid dispenser have been filled with salt and rinse aid respectively, and using the test cycle (see “Cycle Table”).
Lower basket with cutlery basket *) Cutlery basket *) If there are cup racks in place on the lefthand side or if beer glass holders are in place, remove them.
Installation and connection instructions 1 Safety Information for the Installation • Only transport the dishwasher in an upright position, otherwise salt water may run out. • Before using the dishwasher for the first time, check for any damage caused in transport. Do not under any circumstances connect an appliance that is damaged. In the case of damage, please contact your supplier.
Installing the Dishwasher • The dishwasher must be installed on a firm floor and adjusted to ensure that it is stable and level in all directions. • To compensate for unevenness in the floor and to match the height of the appliance to that of surrounding units, extend the threaded feet using a screwdriver. • Adjust the rear feet of the appliance using a screwdriver from the front of the appliance. (See installation instructions.
Connecting the dishwasher Connecting to the water supply • The dishwasher can be connected to cold and hot water supplies up to max. 60°C. • The dishwasher must not be connected to open hot water appliances or instantaneous water heaters. Permitted water pressure Lowest permitted water pressure: 1 bar (=10 N/cm2 =100 kPa) Consult your plumber if the water pressure is less than 1 bar.
Water drainage 1 Drain hose The drain hose must not be kinked, crushed or entangled. Connecting the drain hose: – Maximum permitted height: 1 metre. – Minimum required height: 40 cm above the bottom edge of the appliance. Extension hoses • Extension hoses are available from your local Service Force Centre. To ensure that the function of the appliance is not impeded, the internal diameter of extension hoses must be 19 mm.
Electrical Connection 1 Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. WARNING - This appliance must be earthed. The manufacturer declines any responsibility should these safety measures not be observed. Before switching on make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. To isolate the dishwasher from the mains, remove the mains plug.
Connecting systems The water inlet hose, drain hose and the mains cable must all be connected to the side of the dishwasher as there is no space for them behind the appliance.
Warranty conditions Great Britain Standard guarantee conditions We, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our discretion repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: • The appliance has been correctly installed and used only on the electricity or gas supply stated on the rating plate.
Service and Spare Parts If the event of your appliance requiring service, or if you wish to purchase spare parts, please contact Service Force by telephoning: 0870 5 929 929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www. serviceforce.co.
From the Electrolux Group. The world´s No.1 choice. The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world. AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg-electrolux.
